arXiv subjects

Kimberly A. Dick

Publications and source records attributed to Kimberly A. Dick.

At least 19 recordsLinked to original sources

arXiv2026

Near-Unity Charge Readout in a Nonlinear Resonator without Matching

Dissipative sensors typically use linear resonators with impedance matching to achieve maximal signal and fast operation. The impedance matching, however, sets an upper limit to the bandwidth of the readout. In this paper, we present a nonlinear resonator performing the readout of a double quantum dot charge state via a charge-sensing quantum dot. We show that by driving the resonator in the nonlinear regime, we achieve a near-unity signal for a dissipative sensor. This despite not satisfying the sensor impedance matching requirements necessary for such large signals in the linear regime. Our experiments, supported by numerical calculations, demonstrate that the signal increase stems from the sensor dissipation shifting the onset of the nonlinear resonator response. By lifting the matching requirement, we open up an avenue to ultrafast charge detectors as the resonator input-output coupling - setting the detector bandwidth - does not have to match to the typically much slower sensor dissipation rate.

cond-mat.mes-hall↗

arXiv2026

Self-selective growth of GaAs1-xBix on GaAs zinc blende/wurtzite nanowire heterostructures

Site-selective nanostructure growth and material incorporation at the atomic scale offer a promising pathway for engineering quantum materials and nanodevices. Here, GaAs nanowires (NWs) with an axial heterostructure of alternating zinc blende (Zb) and wurtzite (Wz) crystal phases are employed as templates for site-selective Ga and Bi overgrowth. Using X-ray photoemission electron microscopy (XPEEM) with nanoscale spatial resolution, we map elemental distribution and local chemical bonding to reveal the incorporation behavior of Bi atoms in {110} Zb and {11-20} Wz facets. Bi incorporation proceeds through an anion-exchange process, where Bi atoms replace As, forming local Ga-Bi bonds and producing a thin GaAs1-xBix shell. We observe crystal-phase-dependent Bi incorporation, with higher Bi concentration in the Zb segments than in the neighboring Wz segments within the same NW. Furthermore, the Zb segment with higher Bi content exhibits reduced susceptibility to oxidation compared with the Wz segment, resulting in increased Ga-oxide in the Wz surfaces. This study highlights GaAs NW Zb/Wz heterostructures as a template for controlled growth of GaBi and GaAs1-xBix nanostructures with tailored functionalities for quantum applications

cond-mat.mtrl-sci↗

arXiv2026

Unravelling the Role of Stacking Disorder on the Optoelectronic Properties of Zn3P2

Zinc phosphide (Zn3P2) is a promising photovoltaic absorber for thin-film and flexible solar cells due to its earth-abundant composition and favourable optoelectronic properties. Recent advances in epitaxy have enabled the growth of high-quality Zn3P2 thin films despite the challenges posed by its incompatible lattice parameter and thermal expansion coefficient. However, Zn3P2 remains prone to intrinsic extended defects, such as rotated domains, that can limit device performance. Here, using (scanning) transmission electron microscopy, we identify a previously unreported class of extended defects that appear as planar faults described by displacement vectors lying in the (001) plane. Within a pseudo-cubic description of Zn3P2, we establish a direct correspondence between planar faults and rotated domains, showing that both arise from the flexible ordering of vacant sites in the Zn sublattice. First-principles calculations reveal an extremely low planar-defect formation energy of 2.5 mJ m-2, demonstrating that these defects form at essentially negligible energetic cost, in excellent agreement with their high experimentally observed occurrence. Additional density functional theory (DFT) calculations show that intrinsic planar defects neither introduce mid-gap electronic states nor significantly perturb the local electrostatic potential, indicating that they are electronically benign. Instead, we propose that planar defects indirectly degrade device performance by acting as preferential segregation sites for optically active point defects.

cond-mat.mtrl-sci↗

arXiv2026

Cathodoluminescence Analysis of Defects and Grain Boundaries in Zn3P2 Thin Films Grown on Graphene by MOVPE and MBE

Zn3P2 is a promising earth-abundant absorber for thin-film photovoltaics, yet its development is hindered by the lack of lattice-matched substrates, its incompatible thermal expansion coefficient, and a complex defect landscape. Here, we demonstrate the quasi-van der Waals epitaxy of Zn3P2 on graphene by metal-organic vapour phase epitaxy (MOVPE) and directly link the density of antiphase boundaries to optical emission modulation using correlative electron microscopy and cathodoluminescence (CL). Moreover, it is observed through CL that grain boundaries act as non-radiative sinks for excited charge carriers. The effect extends several micrometres into the grains, making grain boundaries detrimental to the applicability of Zn3P2 in read devices. Further comparison with molecular beam epitaxy grown films reveals the suppression of strain-related sub-bandgap emission in MOVPE-grown material. Overall, quasi-van der Waals epitaxy of Zn3P2 by MOVPE resulted in larger grains and improved material quality. In addition, these results directly link extended defects to recombination pathways in Zn3P2 and highlight grain-size control as a key strategy for improving earth-abundant photovoltaic absorbers.

cond-mat.mtrl-sci↗

arXiv2025

Information Thermodynamics in a Quantum Dot Szilard Engine - Experimentally Investigating Fluctuation Theorems and Thermodynamic Uncertainty Relations

In Szilard's engine, measurement and feedback allows to extract work from an equilibrium environment, a process otherwise forbidden by the laws of thermodynamics. Recent theoretical developments have established fluctuation theorems and thermodynamic uncertainty relations that constrain the fluctuations in Szilard's engine. These relations rely on auxiliary experimental protocols known as backward experiments. Here, we experimentally investigate the thermodynamics of Szilard's engine by implementing two distinct types of backward experiments. We verify and compare the corresponding fluctuation theorems and thermodynamic uncertainty relations associated with each protocol. Our results reveal that the entropy production inferable from measurement may serve as a more relevant quantifier of information than the widely used mutual information.

cond-mat.mes-hall↗

arXiv2025

Unconventional cross sections in zinc phosphide nanowires grown using exclusively earth-abundant components

To enable lightweight and flexible solar cell applications it is imperative to develop direct bandgap absorber materials. Moreover, to enhance the potential sustainability impact of the technologies there is a drive to base the devices on earth-abundant and readily available elements. Herein, we report on the epitaxial growth of Zn3P2 nanowires using exclusively earth-abundant components, using Sn as the nanowire catalyst and Si (111) as the substrate. We observe that the nanowires exhibit a triangular cross section at lower temperatures, a pseudo-pentagonal cross section at intermediate temperatures, and a hexagonal cross section in a twin plane superlattice configuration at high temperatures and high V/II ratios. At low temperatures, the surface facets are constricted into a metastable configuration, yielding the triangular morphology due to the symmetry of the substrate, while intermediate temperatures facilitate the formation of a pseudo-pentagonal morphology with lower surface to volume ratio. The twin plane superlattice structure can only be observed at conditions that facilitate the incorporation of Sn into Zn3P2, which is needed to form heterotwins in the tetragonal structure, namely at high temperatures and high phosphine partial pressures. These findings show a clear pathway to use Zn3P2 nanowires in sustainable solar energy harvesting using exclusively earth-abundant components, as well as opening up a novel route of fabricating quantum wells inside nanowires using heterotwins.

cond-mat.mtrl-sci↗

arXiv2025

High-efficiency microwave photodetection by cavity coupled double dots with single cavity-photon sensitivity

We present a superconducting cavity-coupled double quantum dot (DQD) photodiode that achieves a maximum photon-to-electron conversion efficiency of 25% in the microwave domain. With a higher-quality-factor cavity and improved device design to prevent photon leakages through unwanted pathways, our device measures microwave signals down to 100 aW power level and achieves sensitivity to probe microwave signals with one photon at a time in the cavity. We analyze the photodiode operation using Jaynes-Cummings input-output theory, identifying the key improvements of stronger cavity-DQD coupling needed to achieve near-unity photodetection efficiency. The results presented in this work represent a crucial advancement toward near unity microwave photodetection efficiency with single cavity-photon sensitivity for studies of photon statistics in the microwave range and applications related to quantum information processing.

cond-mat.mes-hall↗

arXiv2025

Interfaces in epitaxially grown Zn3P2 nanowires and their composition dependent optoelectronic properties for photovoltaic applications

Epitaxially grown nanowires have shown promise for photovoltaic applications due to their nanophotonic properties. Moreover, the mechanical properties of nanowires can reduce crystallographic defect formation at interfaces to help enable new material combinations for photovoltaics. One material that stands to benefit from the nanowire morphology is zinc phosphide (Zn3P2), which despite promising optoelectronic properties has experienced limited applicability due to challenges achieving heteroepitaxy, stemming from its large lattice parameter and coefficient of thermal expansion. Herein, we identify the requirements for successful epitaxy of Zn3P2 nanowires using metalorganic chemical vapour deposition and the impact on interface structure and defect formation. Furthermore, using high-throughput optical spectroscopy we were able to demonstrate shifts in the photoluminescence intensity and energy by tuning the V/II ratio during growth, highlighting the compositional tunability of the optoelectronic properties of Zn3P2 nanowires.

cond-mat.mtrl-sci↗

arXiv2024

Coherence of an Electronic Two-Level System under Continuous Charge Sensing by a Quantum Dot Detector

We investigate experimentally the quantum coherence of an electronic two-level system in a double quantum dot under continuous charge detection. The charge-state of the two-level system is monitored by a capacitively coupled single quantum dot detector that imposes a back-action effect to the system. The measured back-action is well described by an additional decoherence rate, approximately linearly proportional to the detector electron tunneling rate. We provide a model for the decoherence rate arising due to level detuning fluctuations induced by detector charge fluctuations. The theory predicts a factor of two lower decoherence rate than observed in the experiment, suggesting the need for a more elaborate theory accounting for additional sources of decoherence.

cond-mat.mes-hall↗

arXiv2024

Microwave power harvesting using resonator-coupled double quantum dot photodiode

We demonstrate a microwave power-to-electrical energy conversion in a resonator-coupled double quantum dot. The system, operated as a photodiode, converts individual microwave photons to electrons tunneling through the double dot, resulting in an electrical current flowing against the applied voltage bias at input powers down to 1 femto-watt. The device attains a maximum power harvesting efficiency of 2%, with the photon-to-electron conversion efficiency reaching 12% in the single photon absorption regime. We find that the power conversion depends on thermal effects showing that thermodynamics plays a crucial role in the single photon energy conversion.

cond-mat.mes-hall↗

arXiv2024

Continuous microwave photon counting by semiconductor-superconductor hybrids

The growing interest in quantum information has enabled the manipulation and readout of microwave photon states with high fidelities. The presently available microwave photon counters, based on superconducting circuits, are limited to non-continuous pulsed mode operation, requiring additional steps for qubit state preparation before an actual measurement. Here, we present a continuous microwave photon counter based on superconducting cavity-coupled semiconductor quantum dots. The device utilizes photon-assisted tunneling in a double quantum dot with tunneling events being probed by a third dot. Our device detects both single and multiple-photon absorption events independently, thanks to the energy tunability of a two-level double-dot absorber. We show that the photon-assisted tunnel rates serve as the measure of the cavity photon state in line with the P(E) theory - a theoretical framework delineating the mediation of the cavity photon field via a two-level environment. We further describe the single photon detection using the Jaynes-Cummings input-output theory and show that it agrees with the P(E) theory predictions.

cond-mat.mes-hall↗

arXiv2023

Strong coupling between a microwave photon and a singlet-triplet qubit

Tremendous progress in few-qubit quantum processing has been achieved lately using superconducting resonators coupled to gate voltage defined quantum dots. While the strong coupling regime has been demonstrated recently for odd charge parity flopping mode spin qubits, first attempts towards coupling a resonator to even charge parity singlet-triplet spin qubits have resulted only in weak spin-photon coupling strengths. Here, we integrate a zincblende InAs nanowire double quantum dot with strong spin-orbit interaction in a magnetic-field resilient, high-quality resonator. In contrast to conventional strategies, the quantum confinement is achieved using deterministically grown wurtzite tunnel barriers without resorting to electrical gating. Our experiments on even charge parity states and at large magnetic fields, allow to identify the relevant spin states and to measure the spin decoherence rates and spin-photon coupling strengths. Most importantly, we find an anti-crossing between the resonator mode in the single photon limit and a singlet-triplet qubit with an electron spin-photon coupling strength of $g/2π=139\pm4$ MHz. Combined with the resonator decay rate $κ/2π=19.8\pm0.2$ MHz and the qubit dephasing rate $γ/2π=116\pm7$ MHz, our system achieves the strong coupling regime in which the coherent coupling exceeds qubit and resonator linewidth. These results pave the way towards large-scale quantum system based on singlet-triplet qubits.

cond-mat.mes-hall↗

arXiv2023

Dephasing in a crystal-phase defined double quantum dot charge qubit strongly coupled to a high-impedance resonator

Dephasing of a charge qubit is usually credited to charge noise in the environment. Here we show that charge noise may not be the limiting factor for the qubit coherence. To this end, we study coherence properties of a crystal-phase defined semiconductor nanowire double quantum dot (DQD) charge qubit strongly coupled to a high-impedance resonator using radio-frequency (RF) reflectometry. Response of this hybrid system is measured both at a charge noise sensitive operation point (with finite DQD detuning) and at an insensitive point (so-called sweet spot with zero detuning). A theoretical model based on Jaynes-Cummings Hamiltonian matches the experimental results well and yields only a 10 % difference in dephasing rates between the two cases, despite that the sensitivity to detuning charge noise differs by a factor of 5. Therefore the charge noise is not the limiting factor for the coherence in this type of semiconducting nanowire qubits.

cond-mat.mes-hall↗

arXiv2023

Quantum Dot Source-Drain Transport Response at Microwave Frequencies

Quantum dots are frequently used as charge sensitive devices in low temperature experiments to probe electric charge in mesoscopic conductors where the current running through the quantum dot is modulated by the nearby charge environment. Recent experiments have been operating these detectors using reflectometry measurements up to GHz frequencies rather than probing the low frequency current through the dot. In this work, we use an on-chip coplanar waveguide resonator to measure the source-drain transport response of two quantum dots at a frequency of 6 GHz, further increasing the bandwidth limit for charge detection. Similar to the low frequency domain, the response is here predominantly dissipative. For large tunnel coupling, the response is still governed by the low frequency conductance, in line with Landauer-Büttiker theory. For smaller couplings, our devices showcase two regimes where the high frequency response deviates from the low frequency limit and Landauer-Büttiker theory: When the photon energy exceeds the quantum dot resonance linewidth, degeneracy dependent plateaus emerge. These are reproduced by sequential tunneling calculations. In the other case with large asymmetry in the tunnel couplings, the high frequency response is two orders of magnitude larger than the low frequency conductance G, favoring the high frequency readout.

cond-mat.mes-hall↗

arXiv2023

Minimally dissipative information erasure in a quantum dot via thermodynamic length

In this work we explore the use of thermodynamic length to improve the performance of experimental protocols. In particular, we implement Landauer erasure on a driven electron level in a semiconductor quantum dot, and compare the standard protocol in which the energy is increased linearly in time with the one coming from geometric optimisation. The latter is obtained by choosing a suitable metric structure, whose geodesics correspond to optimal finite-time thermodynamic protocols in the slow driving regime. We show experimentally that geodesic drivings minimise dissipation for slow protocols, with a bigger improvement as one approaches perfect erasure. Moreover, the geometric approach also leads to smaller dissipation even when the time of the protocol becomes comparable with the equilibration timescale of the system, i.e., away from the slow driving regime. Our results also illustrate, in a single-electron device, a fundamental principle of thermodynamic geometry: optimal finite-time thermodynamic protocols are those with constant dissipation rate along the process.

cond-mat.mes-hall↗

arXiv2022

Energetics of microwaves probed by double quantum dot absorption

We explore the energetics of microwaves interacting with a double quantum dot photodiode and show wave-particle aspects in photon-assisted tunneling. The experiments show that the single photon energy sets the relevant absorption energy in a weak-drive limit, which contrasts the strong drive limit where the wave amplitude determines the relevant-energy scale and opens up microwave induced bias triangles. The threshold condition between these two regimes is set by the fine-structure constant of the system. The energetics are determined here with the detuning conditions of the double dot system and stopping-potential measurements that constitute a microwave version of the photoelectric effect.

cond-mat.mes-hall↗

arXiv2022

Efficient and Continuous Microwave Photodetection in Hybrid Cavity-Semiconductor Nanowire Double Quantum Dot Diodes

Single photon detectors are key for time-correlated photon counting applications [1] and enable a host of emerging optical quantum information technologies [2]. So far, the leading approach for continuous and efficient single-photon detection in the optical domain has been based on semiconductor photodiodes [3]. However, there is a paucity of efficient and continuous single-photon detectors in the microwave regime, because photon energies are four to five orders of magnitude lower therein and conventional photodiodes do not have that sensitivity. Here we tackle this gap and demonstrate how itinerant microwave photons can be efficiently and continuously converted to electrical current in a high-quality, semiconducting nanowire double quantum dot that is resonantly coupled to a cavity. In particular, in our detection scheme, an absorbed photon gives rise to a single electron tunneling event through the double dot, with a conversion efficiency reaching 6 %. Our results pave the way for photodiodes with single-shot microwave photon detection, at the theoretically predicted unit efficiency [4].

cond-mat.mes-hall↗

arXiv2021

Experimental verification of the work fluctuation-dissipation relation for information-to-work conversion

We study experimentally work fluctuations in a Szilard engine that extracts work from information encoded as the occupancy of an electron level in a semiconductor quantum dot. We show that as the average work extracted per bit of information increases towards the Landauer limit $k_BT \ln 2$, the work fluctuations decrease in accordance with the work fluctuation-dissipation relation. We compare the results to a protocol without measurement and feedback and show that when no information is used, the work output and fluctuations vanish simultaneously contrasting the information-to-energy conversion case where increasing amount of work is produced with decreasing fluctuations. Our work highlights the importance of fluctuations in the design of information-to-work conversion processes.

cond-mat.mes-hall↗