arXiv subjects

Klara Lünser

Publications and source records attributed to Klara Lünser.

6 recordsLinked to original sources

arXiv2026

Anomalous thermal and elastic properties of an epitaxial NiTi film exhibiting R-phase

Shape memory alloys like NiTi are at the core of emerging thermal management applications, including elastocaloric refrigeration, thermoelastic harvesting, and latent heat storage. Most of these applications benefit from a small scale due to the accelerated heat exchange, but obtaining precise functional properties of films is challenging. Here we demonstrate that transient grating spectroscopy (TGS) enables characterization of elastic coefficients and thermal diffusivity of a 3 $μ$m thick epitaxial NiTi film during a thermally induced phase transformation. The in-situ measurement of a complete austenite$\rightarrow$R-phase$\rightarrow$martensite$\rightarrow$austenite temperature cycle reveals that the elastic properties exhibit a crossover of the shear moduli (from $c^\prime < c_{44}$ in austenite to $c^\prime > c_{44}$ in martensite) and that the thermal diffusivity changes by 450 $\%$ between the R-phase and austenite. This dramatic change, together with the absence of hysteresis between the R-phase and austenite, makes NiTi a promising material candidate for thermal switches. The results indicate that the change in thermal diffusivity originates from an anomalous heat capacity of the R-phase. Furthermore, our TGS study provides temperature-dependent thermal and elastic properties required for simulating thermal management microsystems using this material.

cond-mat.mtrl-sci↗

arXiv2026

Impact of hydrogen incorporation on electronic and magnetic structure of X2CrNi18-9 stainless steel

Hydrogen absorption significantly alters the mechanical properties of steel. However, absorbed hydrogen also influences its electronic and magneto-structural properties, helping to interpret how hydrogen is incorporated. This study therefore investigates the influence of hydrogen incorporation on the electronic and magneto-structural properties of X2CrNi18-9 stainless steel in different microstructural states. Microstructural characterization included analytic electron microscopy mapping, X-ray diffraction and thermodynamic stability maps to evaluate grain size, dislocation density and chemical homogeneity. The electronic properties were characterized using the Seebeck coefficient, while the magneto-structural properties were investigated using diffuse neutron scattering and small-angle neutron scattering (SANS). Hydrogen incorporation showed clear changes in the Seebeck coefficients. Magnetic SANS in conjunction with diffuse neutron scattering indicates the existence of nanoscale inhomogeneities with the same fcc structure as the bulk, but with correlation lengths of a few nanometres. The size of these inhomogeneities increased with hydrogen incorporation, suggesting that hydrogen preferentially accumulates in their vicinity. However, no direct correlation between the electronic and magneto-structural properties and the dislocation density could be demonstrated. We suggest that studies such as these will lead in the medium term to the development of guidelines for material design to make steels more resistant to hydrogen.

cond-mat.mtrl-sci↗

arXiv2026

Influence of Charge Density Waves on the Hall coefficient in NiTi

We present a mean-field charge density wave theory for NiTi using density functional theory bandstructure as a starting point. We calculate the Hall coefficient as a function of temperature and compare with recent experimental results. We analyze the contributions to the Hall coefficient from different parts of the Fermi surface and find that the Hall coefficient is dominated by certain ``hot spots''. The analysis shows that these hot spots are mostly dominated by Ni d-orbitals. We demonstrate that the Hall coefficient is not well reproduced by Boltzmann transport theory within the constant relaxation time approximation without charge density waves. We consider both uniaxial and biaxial charge density waves and show that biaxial charge density waves can account well for the Hall coefficient, while uniaxial cannot. We also investigate the temperature dependence of the resistivity and the specific heat.

cond-mat.mtrl-sci↗

arXiv2025

Sub-nanosecond structural dynamics of the martensitic transformation in Ni-Mn-Ga

Martensitic transformations drive a multitude of emerging applications, which range from high stroke actuation and, mechanocaloric refrigeration, to thermoelastic energy harvesting. All these applications benefit from faster transformations, as a high cycle frequency is essential for achieving high power density. However, systematic investigations of the fast dynamics and fundamental speed limits of martensitic transformations are scarce. Especially for ultrashort time transformations, the temperature evolution throughout the transformation is not measured, which is a substantial shortcoming as temperature is the intrinsic force driving the transformation. Here, we present a synchrotron-based time-resolved X-ray diffraction study of a 270 fs laser-induced martensitic transformation in a Ni-Mn-Ga-based epitaxial thin film. We observe the transformation from martensite to austenite within about 100 ps, just limited by the synchrotron probe pulse duration. Furthermore, a full transformation cycle from martensite to austenite and back to martensite can almost be finished within 5 ns, which is the fastest martensitic transformation reported so far. Measurements and calculations of the temperature evolution allow us to analyse the influence of temperature on transformation time. By time-resolved strain measurements we demonstrate that in addition to temperature, thermal film stress must be considered as a competing influence on the martensitic transformation. Our experimental findings are supported by molecular dynamics simulations with machine learned force fields adapted to density functional theory calculations. These reveal that the huge distortion during a martensitic transformation requires the collective movement of many atoms within the microstructure, which delays the transformation.

cond-mat.mtrl-sci↗

arXiv2024

Formation of martensitic microstructure in epitaxial Ni-Mn-Ga films after fast cooling

Shape memory alloys have a wide range of applications, including high stroke actuation, energy-efficient ferroic cooling, and energy harvesting. These applications are based on a reversible martensitic transformation, which results in a complex microstructure in the martensitic state. Understanding the formation of this microstructure after fast heating and cooling is crucial, as a high cycle frequency is essential for achieving high power density in the mentioned applications. This article uses an epitaxial Ni-Mn-Ga film as a model system to study the formation of the martensitic microstructure, since the high surface-to-volume ratio of thin films enables rapid heating and cooling, and since the formation of a multi-level hierarchical microstructure during slow cooling of this material system is already well understood. We apply a millisecond flash lamp pulse of varying energy density on the Ni-Mn-Ga film and analyse the hierarchical martensitic microstructure afterwards. Substantial differences compared to slow cooling occur, which we attribute to the limited time available for the microstructure to form and to the thermal stress between film and substrate during rapid temperature changes.

cond-mat.mtrl-sci↗

arXiv2022

What is the speed limit of martensitic transformations?

Structural martensitic transformations enable various applications, which range from high stroke actuation and sensing to energy efficient magnetocaloric refrigeration and thermomagnetic energy harvesting. All these emerging applications benefit from a fast transformation, but up to now the speed limit of martensitic transformations has not been explored. Here, we demonstrate that a martensite to austenite transformation can be completed in under ten nanoseconds. We heat an epitaxial Ni-Mn-Ga film with a laser pulse and use synchrotron diffraction to probe the influence of initial sample temperature and overheating on transformation rate and ratio. We demonstrate that an increase of thermal energy drives this transformation faster. Though the observed speed limit of 2.5 x 10^{27} (Js)^{-1} per unit cell leaves plenty of room for a further acceleration of applications, our analysis reveals that the practical limit will be the energy required for switching. Our experiments unveil that martensitic transformations obey similar speed limits as in microelectronics, which are expressed by the Margolus-Levitin theorem.

cond-mat.mtrl-sci↗