SearcharxivSearch

arXiv subjects

L. Frunzio

Publications and source records attributed to L. Frunzio.

At least 19 recordsLinked to original sources

Characterization of drive-induced unwanted state transitions in superconducting circuits

Microwave drives are essential for implementing control and readout operations in superconducting quantum circuits. However, increasing the drive strength eventually leads to unwanted state transitions which limit the speed and fidelity of such operations. In this work, we systematically investigate such transitions in a fixed-frequency qubit subjected to microwave drives spanning a 9 GHz frequency range. We identify the physical origins of these transitions and classify them into three categories. (1) Resonant energy exchange with parasitic two-level systems, activated by drive-induced ac-Stark shifts, (2) multi-photon transitions to non-computational states, intrinsic to the circuit Hamiltonian, and (3) inelastic scattering processes in which the drive causes a state transition in the superconducting circuit, while transferring excess energy to a spurious electromagnetic mode or two-level system (TLS) material defect. We show that the Floquet steady-state simulation, complemented by an electromagnetic simulation of the physical device, accurately predicts the observed transitions that do not involve TLS. Our results provide a comprehensive classification of these transitions and offer mitigation strategies through informed choices of drive frequency as well as improved circuit design.

quant-ph

Lumped-element broadband SNAIL parametric amplifier with on-chip pump filter for multiplexed readout

We present a SNAIL-based parametric amplifier that integrates a lumped-element impedance matching network for increased bandwidth and an on-chip pump-port filter for efficient pump delivery. The amplifier is fabricated using a single-layer optical lithography step, followed by a single-layer electron beam lithography step. We measure a flat 20 dB gain profile with less than 1 dB ripple across a bandwidth of up to 250 MHz on multiple devices, demonstrating robust performance against variations arising from fabrication and packaging. We characterize the amplifier's linearity by analyzing gain compression and intermodulation distortion under simultaneous multi-tone excitation. We show that the intermodulation products remain suppressed by more than 23 dB relative to the signal tones, even at the 1 dB gain compression point. We further validate its utility by performing simultaneous high-fidelity readout of two transmon qubits, achieving state assignment fidelities of 99.51% and 98.55%. The combination of compact design, fabrication simplicity, and performance robustness makes this amplifier a practical device for quantum experiments with superconducting circuits.

quant-ph

Benchmarking the readout of a superconducting qubit for repeated measurements

Readout of superconducting qubits faces a trade-off between measurement speed and unwanted back-action on the qubit caused by the readout drive, such as $T_1$ degradation and leakage out of the computational subspace. The readout is typically benchmarked by integrating the readout signal and choosing a binary threshold to extract the "readout fidelity". We show that readout fidelity may significantly overlook readout-induced leakage errors. Such errors are detrimental for applications that rely on continuously repeated measurements, e.g., quantum error correction. We introduce a method to measure the readout-induced leakage rate by repeatedly executing a composite operation - a readout preceded by a randomized qubit-flip. We apply this technique to characterize the readout of a superconducting qubit, optimized for fidelity across four different readout durations. Our technique highlights the importance of an independent leakage characterization by showing that the leakage rates vary from $0.12\%$ to $7.76\%$ across these readouts even though the fidelity exceeds $99.5\%$ in all four cases.

quant-ph

Hamiltonian Extrema of an Arbitrary Flux-Biased Josephson Circuit

Flux-biased loops including one or more Josephson junctions are ubiquitous elements in quantum information experiments based on superconducting circuits. These quantum circuits can be tuned to implement a variety of Hamiltonians, with applications ranging from decoherence-protected qubits to quantum limited converters and amplifiers. The extrema of the Hamiltonian of these circuits are of special interest because they govern their low-energy dynamics. However, the theory of superconducting quantum circuits so far lacks a systematic method to find these extrema and compute the series expansion of the Hamiltonian in their vicinity for an arbitrary nonlinear superconducting circuit. We present such a method, which can aid the synthesis of new functionalities in quantum devices.

cond-mat.supr-con

Real-time quantum error correction beyond break-even

The ambition of harnessing the quantum for computation is at odds with the fundamental phenomenon of decoherence. The purpose of quantum error correction (QEC) is to counteract the natural tendency of a complex system to decohere. This cooperative process, which requires participation of multiple quantum and classical components, creates a special type of dissipation that removes the entropy caused by the errors faster than the rate at which these errors corrupt the stored quantum information. Previous experimental attempts to engineer such a process faced an excessive generation of errors that overwhelmed the error-correcting capability of the process itself. Whether it is practically possible to utilize QEC for extending quantum coherence thus remains an open question. We answer it by demonstrating a fully stabilized and error-corrected logical qubit whose quantum coherence is significantly longer than that of all the imperfect quantum components involved in the QEC process, beating the best of them with a coherence gain of $G = 2.27 \pm 0.07$. We achieve this performance by combining innovations in several domains including the fabrication of superconducting quantum circuits and model-free reinforcement learning.

quant-ph

Frequency-tunable Kerr-free three-wave mixing with a gradiometric SNAIL

Three-wave mixing is a key process in superconducting quantum information processing, being involved in quantum-limited amplification and parametric coupling between superconducting cavities. These operations can be implemented by SNAIL-based devices that present a Kerr-free flux-bias point where unwanted parasitic effects such as Stark shift are suppressed. However, with a single flux-bias parameter, these circuits can only host one Kerr-free point, limiting the range of their applications. In this Letter, we demonstrate how to overcome this constraint with a gradiometric SNAIL, a doubly-flux biased superconducting circuit for which both effective inductance and Kerr coefficient can be independently tuned. Experimental data show the capability of the gradiometric SNAIL to suppress Kerr effect in a three-wave mixing parametric amplifier over a continuum of flux bias points corresponding to a 1.7 GHz range of operating frequencies.

cond-mat.supr-con

Ac losses in field-cooled type I superconducting cavities

As superconductors are cooled below their critical temperature, stray magnetic flux can become trapped in regions that remain normal. The presence of trapped flux facilitates dissipation of ac current in a superconductor, leading to losses in superconducting elements of microwave devices. In type II superconductors, dissipation is well-understood in terms of the dynamics of vortices hosting a single flux quantum. In contrast, the ac response of type I superconductors with trapped flux has not received much attention. Building on Andreev's early work [Sov. Phys. JETP 24, 1019 (1967)], here we show theoretically that the dominant dissipation mechanism is the absorption of the ac field at the exposed surfaces of the normal regions, while the deformation of the superconducting/normal interfaces is unimportant. We use the developed theory to estimate the degradation of the quality factors in field-cooled cavities, and we satisfactorily compare these theoretical estimates to the measured field dependence of the quality factors of two aluminum cavities.

cond-mat.supr-con

Free-standing silicon shadow masks for transmon qubit fabrication

Nanofabrication techniques for superconducting qubits rely on resist-based masks patterned by electron-beam or optical lithography. We have developed an alternative nanofabrication technique based on free-standing silicon shadow masks fabricated from silicon-on-insulator wafers. These silicon shadow masks not only eliminate organic residues associated with resist-based lithography, but also provide a pathway to better understand and control surface-dielectric losses in superconducting qubits by decoupling mask fabrication from substrate preparation. We have successfully fabricated aluminum 3D transmon superconducting qubits with these shadow masks and found coherence quality factors comparable to those fabricated with standard techniques.

physics.app-ph

Quantum error correction of a qubit encoded in grid states of an oscillator

Quantum bits are more robust to noise when they are encoded non-locally. In such an encoding, errors affecting the underlying physical system can then be detected and corrected before they corrupt the encoded information. In 2001, Gottesman, Kitaev and Preskill (GKP) proposed a hardware-efficient instance of such a qubit, which is delocalised in the phase-space of a single oscillator. However, implementing measurements that reveal error syndromes of the oscillator while preserving the encoded information has proved experimentally challenging: the only realisation so far relied on post-selection, which is incompatible with quantum error correction (QEC). The novelty of our experiment is precisely that it implements these non-destructive error-syndrome measurements for a superconducting microwave cavity. We design and implement an original feedback protocol that incorporates such measurements to prepare square and hexagonal GKP code states. We then demonstrate QEC of an encoded qubit with unprecedented suppression of all logical errors, in quantitative agreement with a theoretical estimate based on the measured imperfections of the experiment. Our protocol is applicable to other continuous variable systems and, in contrast with previous implementations of QEC, can mitigate all logical errors generated by a wide variety of noise processes, and open a way towards fault-tolerant quantum computation.

quant-ph

Direct Dispersive Monitoring of Charge Parity in Offset-Charge-Sensitive Transmons

A striking characteristic of superconducting circuits is that their eigenspectra and intermode coupling strengths are well predicted by simple Hamiltonians representing combinations of quantum circuit elements. Of particular interest is the Cooper-pair-box Hamiltonian used to describe the eigenspectra of transmon qubits, which can depend strongly on the offset-charge difference across the Josephson element. Notably, this offset-charge dependence can also be observed in the dispersive coupling between an ancillary readout mode and a transmon fabricated in the offset-charge-sensitive (OCS) regime. We utilize this effect to achieve direct, high-fidelity dispersive readout of the joint plasmon and charge-parity state of an OCS transmon, which enables efficient detection of charge fluctuations and nonequilibrium-quasiparticle dynamics. Specifically, we show that additional high-frequency filtering can extend the charge-parity lifetime of our device by two orders of magnitude, resulting in a significantly improved energy relaxation time $T_1\sim200~μ\mathrm{s}$.

cond-mat.mes-hall

Fault-tolerant detection of a quantum error

A critical component of any quantum error-correcting scheme is detection of errors by using an ancilla system. However, errors occurring in the ancilla can propagate onto the logical qubit, irreversibly corrupting the encoded information. We demonstrate a fault-tolerant error-detection scheme that suppresses spreading of ancilla errors by a factor of 5, while maintaining the assignment fidelity. The same method is used to prevent propagation of ancilla excitations, increasing the logical qubit dephasing time by an order of magnitude. Our approach is hardware-efficient, as it uses a single multilevel transmon ancilla and a cavity-encoded logical qubit, whose interaction is engineered in situ by using an off-resonant sideband drive. The results demonstrate that hardware-efficient approaches that exploit system-specific error models can yield advances toward fault-tolerant quantum computation.

quant-ph

Quantum back-action of variable-strength measurement

Measuring a quantum system can randomly perturb its state. The strength and nature of this back-action depends on the quantity which is measured. In a partial measurement performed by an ideal apparatus, quantum physics predicts that the system remains in a pure state whose evolution can be tracked perfectly from the measurement record. We demonstrate this property using a superconducting qubit dispersively coupled to a cavity traversed by a microwave signal. The back-action on the qubit state of a single measurement of both signal quadratures is observed and shown to produce a stochastic operation whose action is determined by the measurement result. This accurate monitoring of a qubit state is an essential prerequisite for measurement-based feedback control of quantum systems.

quant-ph

Hot non-equilibrium quasiparticles in transmon qubits

Non-equilibrium quasiparticle excitations degrade the performance of a variety of superconducting circuits. Understanding the energy distribution of these quasiparticles will yield insight into their generation mechanisms, the limitations they impose on superconducting devices, and how to efficiently mitigate quasiparticle-induced qubit decoherence. To probe this energy distribution, we systematically correlate qubit relaxation and excitation with charge-parity switches in an offset-charge-sensitive transmon qubit, and find that quasiparticle-induced excitation events are the dominant mechanism behind the residual excited-state population in our samples. By itself, the observed quasiparticle distribution would limit $T_1$ to $\approx200~μ\mathrm{s}$, which indicates that quasiparticle loss in our devices is on equal footing with all other loss mechanisms. Furthermore, the measured rate of quasiparticle-induced excitation events is greater than that of relaxation events, which signifies that the quasiparticles are more energetic than would be predicted from a thermal distribution describing their apparent density.

cond-mat.mes-hall

Gated conditional displacement readout of superconducting qubits

We have realized a new interaction between superconducting qubits and a readout cavity that results in the displacement of a coherent state in the cavity, conditioned on the state of the qubit. This conditional state, when it reaches the cavity-following, phase-sensitive amplifier, matches its measured observable, namely the in-phase quadrature. In a setup where several qubits are coupled to the same readout resonator, we show it is possible to measure the state of a target qubit with minimal dephasing of the other qubits. Our results suggest novel directions for faster readout of superconducting qubits and implementations of bosonic quantum error-correcting codes.

quant-ph

Driving forbidden transitions in the fluxonium artificial atom

Atomic systems display a rich variety of quantum dynamics due to the different possible symmetries obeyed by the atoms. These symmetries result in selection rules that have been essential for the quantum control of atomic systems. Superconducting artificial atoms are mainly governed by parity symmetry. Its corresponding selection rule limits the types of quantum systems that can be built using electromagnetic circuits at their optimal coherence operation points ("sweet spots"). Here, we use third-order nonlinear coupling between the artificial atom and its readout resonator to drive transitions forbidden by the parity selection rule for linear coupling to microwave radiation. A Lambda-type system emerges from these newly accessible transitions, implemented here in the fluxonium artificial atom coupled to its "antenna" resonator. We demonstrate coherent manipulation of the fluxonium artificial atom at its sweet spot by stimulated Raman transitions. This type of transition enables the creation of new quantum operations, such as the control and readout of physically protected artificial atoms.

quant-ph

Programmable interference between two microwave quantum memories

Interference experiments provide a simple yet powerful tool to unravel fundamental features of quantum physics. Here we engineer an RF-driven, time-dependent bilinear coupling that can be tuned to implement a robust 50:50 beamsplitter between stationary states stored in two superconducting cavities in a three-dimensional architecture. With this, we realize high contrast Hong-Ou- Mandel (HOM) interference between two spectrally-detuned stationary modes. We demonstrate that this coupling provides an efficient method for measuring the quantum state overlap between arbitrary states of the two cavities. Finally, we showcase concatenated beamsplitters and differential phase shifters to implement cascaded Mach-Zehnder interferometers, which can control the signature of the two-photon interference on-demand. Our results pave the way toward implementation of scalable boson sampling, the application of linear optical quantum computing (LOQC) protocols in the microwave domain, and quantum algorithms between long-lived bosonic memories.

quant-ph

Deterministic teleportation of a quantum gate between two logical qubits

A quantum computer has the potential to effciently solve problems that are intractable for classical computers. Constructing a large-scale quantum processor, however, is challenging due to errors and noise inherent in real-world quantum systems. One approach to this challenge is to utilize modularity--a pervasive strategy found throughout nature and engineering--to build complex systems robustly. Such an approach manages complexity and uncertainty by assembling small, specialized components into a larger architecture. These considerations motivate the development of a quantum modular architecture, where separate quantum systems are combined via communication channels into a quantum network. In this architecture, an essential tool for universal quantum computation is the teleportation of an entangling quantum gate, a technique originally proposed in 1999 which, until now, has not been realized deterministically. Here, we experimentally demonstrate a teleported controlled-NOT (CNOT) operation made deterministic by utilizing real-time adaptive control. Additionally, we take a crucial step towards implementing robust, error-correctable modules by enacting the gate between logical qubits, encoding quantum information redundantly in the states of superconducting cavities. Such teleported operations have significant implications for fault-tolerant quantum computation, and when realized within a network can have broad applications in quantum communication, metrology, and simulations. Our results illustrate a compelling approach for implementing multi-qubit operations on logical qubits within an error-protected quantum modular architecture.

quant-ph

Deterministic remote entanglement of superconducting circuits through microwave two-photon transitions

Large-scale quantum information processing networks will most probably require the entanglement of distant systems that do not interact directly. This can be done by performing entangling gates between standing information carriers, used as memories or local computational resources, and flying ones, acting as quantum buses. We report the deterministic entanglement of two remote transmon qubits by Raman stimulated emission and absorption of a traveling photon wavepacket. We achieve a Bell state fidelity of 73 %, well explained by losses in the transmission line and decoherence of each qubit.

quant-ph