arXiv subjects

Laurent Pinard

Publications and source records attributed to Laurent Pinard.

At least 19 recordsLinked to original sources

arXiv2026

The MICADO first-light imager for the ELT: first steps of the SCAO system MAIT

MICADO is the ELT first light instrument, an imager working at the diffraction limit of the telescope thanks to two adaptive optics (AO) modes: a single conjugate one (SCAO), available at the instrument first light and developed by the MICADO consortium, and a multi conjugate one (MCAO), developed by the MORFEO consortium. Although the project final design review process is about to be completed, the review board and ESO acknowledged that "the review of the final design can be considered complete for the majority of the MICADO sub-systems" and agreed that MICADO can start manufacturing. For the MICADO SCAO module, we have started the manufacturing of several parts: the majority of the SCAO optics and of the SCAO mechanics, the real-time computer software and the instrument control software. This manufacturing is ordered in several steps to allow the progressive integration of a first full AO close loop with the final SCAO parts. In this contribution, we will focus on the first two steps: on our AO S\'esame bench and the so-called "beta flat configuration". We will present the status of this manufacturing and the first results obtained.

astro-ph.IM↗

arXiv2026

The MICADO first light imager for the ELT: the SCAO module AIT in France, from the beta flat configuration towards the flat and final configurations

MICADO is the designated ELT first light instrument, a near-infrared imager working at the diffraction limit of the telescope thanks to a SCAO and an MCAO mode. Since summer 2024, MICADO is in its AIT phase and all MICADO partners are currently integrating their subsystems. The MICADO SCAO module will follow three successive AIT phases in France: the beta flat configuration, the flat configuration and the final configuration. In this contribution I will first present the progress made in the AIT of the beta flat configuration and its closed loop results. I will then present the performed and on-going tasks for the flat and final configurations (manufacturing, delivery and integration of several SCAO subsystems and pieces of software) and the results obtained so far in the flat configuration. I will then conclude with the expected following steps of the SCAO module AIT in Garching.

astro-ph.IM↗

arXiv2026

MORFEO: Advancing Towards Final Design

The Multiconjugate adaptive Optics Relay For ELT Observations (MORFEO) is a first-generation adaptive optics module for the Extremely Large Telescope (ELT), designed to deliver a diffraction-limited, highly uniform 53x53 arcsec field of view to the MICADO near-infrared camera. As the project advances toward its Final Design Review (FDR), significant consolidations have been achieved across all subsystems. This paper presents an updated overview of the MORFEO system, highlighting its dual operational modes (MCAO and SCAO) and recent developments in its opto-mechanical architecture. We dedicate specific focus to the core adaptive hardware, detailing the fifth-generation post-focal deformable mirrors, the highly complex Laser Guide Star (LGS) objective zoom system required to track sodium layer variations, and the Natural Guide Star (NGS) low-order and reference sensing strategies. Furthermore, we detail the advanced pseudo-open-loop control strategy managed by a split Hard and Soft Real-Time Computer architecture. Finally, we report the latest end-to-end performance estimations obtained via the SPECULA simulation framework, demonstrating compliance with the stringent Strehl Ratio and sky coverage requirements under median atmospheric conditions.

astro-ph.IM↗

arXiv2026

Widefield Spectroscopic Telescope (WST): coating strategy to achieve high optical throughput

The Wide-field Spectroscopic Telescope (WST) is a 12-m class facility designed for simultaneous wide-field multi-object and integral-field spectroscopy across 370-1600 nm, targeting a throughput above 83% its wide-field focus and 76% at its integral field one. Its 13 mirrors and 5 lenses require optimized coatings balancing feasibility, operational needs, and long-term durability. Large mirrors (>2 m) may use enhanced metallic coatings, such as the protected-silver solution from the Vera C. Rubin Observatory, achieving over 90% reflectivity in UV and above 99% in NIR. Smaller mirrors would use Nb2O5/SiO2 dielectric stacks, offering 99% reflectivity, tunable spectral response, and excellent stability. Coating the large lenses (up to 1.6 m) is challenging due to the ultra-broadband range, traditional multilayer antireflective coatings show limitations from manufacturing and incidence-angle effects. Graded-index AR coatings are being explored for superior performance across broad wavelengths and angles.

astro-ph.IM↗

arXiv2024

Comparison of arm cavity optical losses for the two wavelengths of the Einstein Telescope gravitational wave detector

A new generation of gravitational wave detectors is currently being designed with the likely use of a different laser wavelength compared to current instruments. The estimation of the optical losses for this new wavelength is particularly relevant to derive the detector sensitivity and also to anticipate the optical performances of future instruments. In this article, we measured the absorption and angle-resolved scattering of several mirror samples in order to compare optical losses at a wavelength of 1064 and 1550\ nm. In addition, we have carried out simulations of the Einstein Telescope arm cavities at 1064 and 1550\ nm taking into account losses due to surface low-spatial frequency flatness. Our results suggest that optical losses as measured at 1064\ nm are about twice as large as those at 1550\ nm as predicted with a simple model.

physics.optics↗

arXiv2024

The Blue Multi Unit Spectroscopic Explorer (BlueMUSE) on the VLT: characterization of two VPHG prototypes based on dichromated gelatin and photopolymer recording materials

Volume-phase holographic gratings (VPHGs) are widely used in astronomical spectrographs due to their adaptability and high diffraction efficiency. Most VPHGs in operation use dichromated gelatin as a recording material, whose performance is sensitive to the coating and development process, especially in the near-UV. In this letter, we present the characterization of two UV-blue VPHG prototypes for the BlueMUSE integral field spectrograph on the VLT, based on dichromated gelatin and the Bayfol$\circledR$HX photopolymer film as recording materials. Our measurements show that both prototypes meet the required diffraction efficiency and exhibit similar performance with a wavelength-average exceeding 70% in the 350-580 nm range. Deviations from theoretical models increase towards 350 nm, consistently with previous studies on similar gratings. We also report similar performances in terms spatial uniformity and grating-to-grating consistency. Likewise, no significant differences in wavefront error or scattered light are observed between the prototypes.

astro-ph.IM↗

arXiv2023

TiO2 doping effect on reflective coating mechanical loss for gravitational wave detection at low temperature

We measured the mechanical loss of a dielectric multilayer reflective coating (ion-beam-sputtered SiO2 and Ta2O5) with and without TiO2 on sapphire disks between 6 and 77 K. The measured loss angle exhibited a temperature dependence, and the local maximum was found at approximately 20 K. This maximum was 7.0*10^(-4) (with TiO2) and 7.7*10^(-4) (without TiO2), although the previous measurement for the coating on sapphire disks showed almost no temperature dependence (Phys. Rev. D 74 022002 (2006)). We evaluated the coating thermal noise in KAGRA and discussed future investigation strategies.

gr-qc↗

arXiv2023

MORFEO enters final design phase

MORFEO (Multi-conjugate adaptive Optics Relay For ELT Observations, formerly MAORY), the MCAO system for the ELT, will provide diffraction-limited optical quality to the large field camera MICADO. MORFEO has officially passed the Preliminary Design Review and it is entering the final design phase. We present the current status of the project, with a focus on the adaptive optics system aspects and expected milestones during the next project phase.

astro-ph.IM↗

arXiv2022

A Systematic Error in the Internal Friction Measurement of Coatings for Gravitational Waves Detectors

Low internal friction coatings are key components of advanced technologies such as optical atomic clocks and high-finesse optical cavity and often lie at the forefront of the most advanced experiments in Physics. Notably, increasing the sensitivity of gravitational-wave detectors depends in a very large part on developing new coatings, which entails developing more suitable methods and models to investigate their loss angle. In fact, the most sensitive region of the detection band in such detectors is limited by the coating thermal noise, which is related to the loss angle of the coating. Until now, models which describe only ideal physical properties have been adopted, wondering about the use of one or more loss angles to describe the mechanical properties of coatings. Here we show the presence of a systematic error ascribed to inhomogeneity of the sample at its edges in measuring the coating loss angle. We present a model for disk-shaped resonators, largely used in loss angle measurements, and we compare the theory with measurements showing how this systematic error impacts on the accuracy with which the loss model parameters are known.

astro-ph.IM↗

arXiv2022

Effects of mixing and annealing on the optical and mechanical properties of TiO$_{2}$:Ta$_{2}$O$_{5}$ amorphous coatings

Amorphous mixed titania-tantala coatings are key components of Bragg reflectors in the gravitational wave detectors (GWDs). Attaining the lowest possible values of optical absorption and mechanical losses in the coatings is of paramount importance for GWDs, and this requires a complex optimization of the coating deposition and post-deposition annealing. We present here a systematic investigation of the optical properties and internal friction of amorphous mixed titania-tantala coatings grown by ion beam sputtering. We consider coatings with six different cation mixing ratios and we study them both in the as-deposited and annealed state. By exploiting spectroscopic ellipsometry data and modelling, along with ancillary techniques, we retrieved the dielectric function of the coatings in a wide spectral range. When varying the mixing ratio and performing the annealing we find monotonic trends for most of the aforementioned properties. Remakably, the post-annealing Urbach energy displays a definite minimum for a mixing ratio around 20%, very close to the composition of the coatings showing the lowest optical absorption for GWDs applications. We suggest that the observed minimum in the Urbach energy depends not only on the mixing ratio, but also on the annealing parameters. On the other hand, the minimum coating loss angle was found to be weakly dependent on the considered measurement frequency and to lie within a rather broad range of Ti content, suggesting that the search for an absolute minimum following post-deposition annealing should be rather sought in the study of the best annealing parameters for each specific cation ratio considered. This work constitutes a reference for the optical properties of the amorphous mixed titania-tantala coatings, and highlights the relevance of the Urbach energy in the optimization process of materials for high-performing Bragg reflectors.

physics.app-ph↗

arXiv2020

Point defects in IBS coating for very low loss mirrors

High reflective coatings are used in many physics experiments. Despite the high quality of the opticalcoating, the performances of the mirrors is altered by the scattered light induced by micrometers sizedefects in the coating layers. The topic of this paper is the study of the point-like scatterers present in thespecific coating of the mirrors used in state of the art, high sensitivity optical experiments. We studied thebehavior of the materials according to different thicknesses, and how the defects change after annealing.To our knowledge, this is a first insight into the formation of such defects for different materials andthickness and how this is reduced when samples are annealed.

physics.ins-det↗

arXiv2020

Estimation of losses in a 300 m filter cavity and quantum noise reduction in the KAGRA gravitational-wave detector

The sensitivity of the gravitational-wave detector KAGRA, presently under construction, will be limited by quantum noise in a large fraction of its spectrum. The most promising technique to increase the detector sensitivity is the injection of squeezed states of light, where the squeezing angle is dynamically rotated by a Fabry-Pérot filter cavity. One of the main issues in the filter cavity design and realization is the optical losses due to the mirror surface imperfections. In this work we present a study of the specifications for the mirrors to be used in a 300 m filter cavity for the KAGRA detector. A prototype of the cavity will be constructed at the National Astronomical Observatory of Japan, inside the infrastructure of the former TAMA interferometer. We also discuss the potential improvement of the KAGRA sensitivity, based on a model of various realistic sources of losses and their influence on the squeezing amplitude.

astro-ph.IM↗

arXiv2020

Observation of a Correlation Between Internal friction and Urbach Energy in Amorphous Oxides Thin Films

We have investigated by spectroscopic ellipsometry (SE, 190-1700 nm) the optical properties of uniform, amorphous thin films of Ta2O5 and Nb2O5 as deposited and after annealing, and after so-called "doping" with Ti atoms which leads to mixed oxides. Ta2O5 and Ti:Ta2O5 are currently used as high-index components in Bragg reflectors for Gravitational Wave Detectors. Parallel to the optical investigation, we measured the mechanical energy dissipation of the same coatings, through the so-called "loss angle" phi = Q^-1, which quantifies the energy loss in materials. By applying the well-known Cody-Lorentz model in the analysis of SE data we have been able to derive accurate information on the fundamental absorption edge through important parameters related to the electronic density of states, such as the optical gap (E_g) and the energy width of the exponential Urbach tail (the Urbach energy E_U). We have found that E_U is neatly reduced by suitable annealing as is also perceptible from direct inspection of SE data. Ti-doping also points to a minor decrease of E_U. The reduction of E_U parallels a lowering of the mechanical losses quantified by the loss angle phi. The correlation highlights that both the electronic states responsible of Urbach tail and the internal friction are sensitive to a self-correlation of defects on a medium-range scale, which is promoted by annealing and in our case, to a lesser extent, by doping. These observations may contribute to a better understanding of the relationship between structural and mechanical properties in amorphous oxides.

physics.optics↗

arXiv2020

Progress in the measurement and reduction of thermal noise in optical coatings for gravitational-wave detectors

Coating thermal noise is a fundamental limit for precision experiments based on optical and quantum transducers. In this review, after a brief overview of the techniques for coating thermal noise measurements, we present the latest world-wide research activity on low-noise coatings, with a focus on the results obtained at the Laboratoire des Matériaux Avancés. We report new updated values for the Ta$_2$O$_5$, Ta$_2$O$_5$-TiO$_2$ and SiO$_2$ coatings of the Advanced LIGO, Advanced Virgo and KAGRA detectors, and new results from sputtered Nb$_2$O$_5$, TiO$_2$-Nb$_2$O$_5$, Ta$_2$O$_5$-ZrO$_2$, MgF$_2$, AlF$_3$ and silicon nitride coatings. Amorphous silicon, crystalline coatings, high-temperature deposition, multi-material coatings and composite layers are also briefly discussed, together with the latest developments of structural analyses and models.

physics.ins-det↗

arXiv2019

Amorphous optical coatings of present gravitational-wave interferometers

We report on the results of an extensive campaign of optical and mechanical characterization of the ion-beam sputtered oxide layers (Ta$_2$O$_5$, TiO$_2$, Ta$_2$O$_5$-TiO$_2$, SiO$_2$) within the high-reflection coatings of the Advanced LIGO, Advanced Virgo and KAGRA gravitational-wave detectors: refractive index, thickness, optical absorption, composition, density, internal friction and elastic constants have been measured; the impact of deposition rate and post-deposition annealing on coating internal friction has been assessed. For Ta$_2$O$_5$ and SiO$_2$ layers, coating internal friction increases with the deposition rate, whereas the annealing treatment either erases or largely reduces the gap between samples with different deposition history. For Ta$_2$O$_5$-TiO$_2$ layers, the reduction of internal friction due to TiO$_2$ doping becomes effective only if coupled with annealing. All measured samples showed a weak dependence of internal friction on frequency ($ϕ_c(f) = af^{b}$, with $-0.208 < b < 0.140$ depending on the coating material considered). SiO$_2$ films showed a mode-dependent loss branching, likely due to spurious losses at the coated edge of the samples. The reference loss values of the Advanced LIGO and Advanced Virgo input (ITM) and end (ETM) mirror HR coatings have been updated by using our estimated value of Young's modulus of Ta$_2$O$_5$-TiO$_2$ layers (120 GPa) and are about 10\% higher than previous estimations.

physics.ins-det↗

arXiv2018

Measurement of optical losses in a high-finesse 300 m filter cavity for broadband quantum noise reduction in gravitational-wave detectors

Earth-based gravitational-wave detectors will be limited by quantum noise in a large part of their spectrum. The most promising technique to achieve a broadband reduction of such noise is the injection of a frequency dependent squeezed vacuum state from the output port of the detector, whit the squeeze angle rotated by the reflection off a Fabry-Perot filter cavity. One of the most important parameters limiting the squeezing performance is represented by the optical losses of the filter cavity. We report here the operation of a 300 m filter cavity prototype installed at the National Astronomical Observatory of Japan (NAOJ). The cavity is designed to obtain a rotation of the squeeze angle below 100 Hz. After achieving the resonance of the cavity with a multi-wavelength technique, the round trip losses have been measured to be between 50 ppm and 90 ppm. This result demonstrates that with realistic assumption on the input squeeze factor and on the other optical losses, a quantum noise reduction of at least 4 dB in the frequency region dominated by radiation pressure can be achieved.

astro-ph.IM↗

arXiv2017

High-Reflection Coatings for Gravitational-Wave Detectors: State of The Art and Future Developments

We report on the optical, mechanical and structural characterization of the sputtered coating materials of Advanced LIGO, Advanced Virgo and KAGRA gravitational-waves detectors. We present the latest results of our research program aiming at decreasing coating thermal noise through doping, optimization of deposition parameters and post-deposition annealing. Finally, we propose sputtered Si3N4 as a candidate material for the mirrors of future detectors.

physics.ins-det↗

arXiv2017

Correlated evolution of structure and mechanical loss of a sputtered silica film

Energy dissipation in amorphous coatings severely affects high-precision optical and quantum transducers. In order to isolate the source of coating loss, we performed an extensive study of Raman scattering and mechanical loss of a thermally-treated sputtered silica coating. Our results show that loss is correlated with the population of three-membered rings of Si-O$_4$ tetrahedral units, and support the evidence that thermal treatment reduces the density of metastable states separated by a characteristic energy of about 0.5 eV, in favour of an increase of the states separated by smaller activation energies. Finally, we conclude that three-fold rings are involved in the relaxation mechanisms only if they belong to more complex chain-like structures of 10 to 100 tetrahedra.

cond-mat.mtrl-sci↗