arXiv subjects

Linbin Huang

Publications and source records attributed to Linbin Huang.

36 records · Page 2Linked to original sources

arXiv2024

Quantitative Stability Conditions for Grid-Forming Converters With Complex Droop Control

In this paper, we analytically study the transient stability of grid-connected converters with grid-forming complex droop control, also known as dispatchable virtual oscillator control. We prove theoretically that complex droop control, as a state-of-the-art grid-forming control, always possesses steady-state equilibria whereas classical droop control does not. We provide quantitative conditions for complex droop control maintaining transient stability (global asymptotic stability) under grid disturbances, which is beyond the well-established local (non-global) stability for classical droop control. For the transient instability of complex droop control, we reveal that the unstable trajectories are bounded, manifesting as limit cycle oscillations. Moreover, we extend our stability results from second-order grid-forming control dynamics to full-order system dynamics that additionally encompass both circuit electromagnetic transients and inner-loop dynamics. Our theoretical results contribute an insightful understanding of the transient stability and instability of complex droop control and offer practical guidelines for parameter tuning and stability guarantees.

eess.SY↗

arXiv2024

How Many Grid-Forming Converters Do We Need? A Perspective From Small Signal Stability and Power Grid Strength

Grid-forming (GFM) control has been considered a promising solution for accommodating large-scale power electronics converters into modern power grids thanks to its grid-friendly dynamics, in particular, voltage source behavior on the AC side. The voltage source behavior of GFM converters can provide voltage support for the power grid, and therefore enhance the power grid (voltage) strength. However, grid-following (GFL) converters can also perform constant AC voltage magnitude control by properly regulating their reactive current, which may also behave like a voltage source. Currently, it still remains unclear what are the essential differences between the voltage source behaviors of GFL and GFM converters, and which type of voltage source behavior can enhance the power grid strength. In this paper, we will demonstrate that only GFM converters can provide effective voltage source behavior and enhance the power grid strength in terms of small signal dynamics. Based on our analysis, we further study the problem of how to configure GFM converters in the grid and how many GFM converters we will need. We investigate how the capacity ratio between GFM and GFL converters affects the equivalent power grid strength and thus the small signal stability of the system. We give guidelines on how to choose this ratio to achieve a desired stability margin. We validate our analysis using high-fidelity simulations.

eess.SY↗

arXiv2024

Ensuring Disturbance Rejection Performance by Synthesizing Grid-Following and Grid-Forming Inverters in Power Systems

To satisfy dynamic requirements of power systems, it is imperative for grid-tied inverters to ensure good disturbance rejection performance (DRP) under variable grid conditions. This letter discovers and theoretically proves that for general networks, synthesizing grid-following (GFL) inverters and grid-forming (GFM) inverters can always more effectively ensure the DRP of multiple inverters, as compared to homogeneous inverter-based systems that solely utilize either GFL or GFM inverters. The synthesis of GFL inverters and GFM inverters can concurrently increase the smallest eigenvalue and decrease the largest eigenvalue of the network grounded Laplacian matrix. This can be equivalent to rematching the proper short-circuit ratio (SCR) for GFL and GFM inverters, thereby ensuring the DRP of inverters both in weak and strong grids. The results reveal the necessity of synthesizing diverse inverter control schemes from the network-based perspective. Sensitivity function-based tests and real-time simulations validate our results.

eess.SY↗

arXiv2024

Characterizing the Role of Complex Power in Small-Signal Synchronization Stability of Multi-Converter Power Systems

Small-signal synchronization instability (SSI) may be triggered when a grid-connected converter is operated in weak grids. This problem is highly related to the active and reactive power (referred to as complex power) generation or consumption of the converter. Such an instability phenomenon manifests as power oscillations within the bandwidth frequency of phase-locked loop (PLL). However, in a multi-converter power system (MCPS), it is challenging to characterize the role of each converter's complex power in SSI issues due to the high dimension of system dynamics. In this paper, we focus on the impact regularity of complex power on the small-signal synchronization stability of the MCPS. Firstly, we formulate the modeling of the MCPS and develop a systematical stability indicator to explicitly quantify the stability margin under various operating complex power. Then, based on the proposed stability indicator, the "resultant force" of complex power on the stability margin of the MCPS can be analytically characterized into a weighted summation form. Furthermore, we elaborate on the impact of each converter's active power and reactive power, respectively. Notably, we demonstrate the cancellation effect between the active power generation and consumption on the stability margin, which ultimately helps prevent SSI issues in the MCPS. The correctness of theoretical findings is well verified by simulations results.

eess.SY↗

arXiv2024

Gain and Phase: Decentralized Stability Conditions for Power Electronics-Dominated Power Systems

This paper proposes decentralized stability conditions for multi-converter systems based on the combination of the small gain theorem and the small phase theorem. Instead of directly computing the closed-loop dynamics, e.g., eigenvalues of the state-space matrix, or using the generalized Nyquist stability criterion, the proposed stability conditions are more scalable and computationally lighter, which aim at evaluating the closed-loop system stability by comparing the individual converter dynamics with the network dynamics in a decentralized and open-loop manner. Moreover, our approach can handle heterogeneous converters' dynamics and is suitable to analyze large-scale multi-converter power systems that contain grid-following (GFL), grid-forming (GFM) converters, and synchronous generators. Compared with other decentralized stability conditions, e.g., passivity-based stability conditions, the proposed conditions are significantly less conservative and can be generally satisfied in practice across the whole frequency range.

eess.SY↗

arXiv2023

MIMO Grid Impedance Identification of Three-Phase Power Systems: Parametric vs. Nonparametric Approaches

A fast and accurate grid impedance measurement of three-phase power systems is crucial for online assessment of power system stability and adaptive control of grid-connected converters. Existing grid impedance measurement approaches typically rely on pointwise sinusoidal injections or sequential wideband perturbations to identify a nonparametric grid impedance curve via fast Fourier computations in the frequency domain. This is not only time-consuming, but also inaccurate during time-varying grid conditions, while on top of that, the identified nonparametric model cannot be immediately used for stability analysis or control design. To tackle these problems, we propose to use parametric system identification techniques (e.g., prediction error or subspace methods) to obtain a parametric impedance model directly from time-domain current and voltage data. Our approach relies on injecting wideband excitation signals in the converter's controller and allows to accurately identify the grid impedance in closed loop within one injection and measurement cycle. Even though the underlying parametric system identification techniques are well-studied in general, their utilization in a grid impedance identification setup poses specific challenges, is vastly underexplored, and has not gained adequate attention in urgent and timely power systems applications. To this end, we demonstrate in numerical experiments how the proposed parametric approach can accomplish a significant improvement compared to prevalent nonparametric methods.

eess.SY↗

arXiv2023

Robust Adaptive Control of STATCOMs to Mitigate Inverter-Based-Resource (IBR)-Induced Oscillations

The interaction among inverter-based resources (IBRs) and power network may cause small-signal stability issues, especially in low short-circuit-level grids. Besides, integrating static synchronous compensators (STATCOMs) in a multi-IBR system for voltage support can deteriorate small-signal stability. However, it is still challenging to fully understand the impact mechanism of STATCOMs on IBR-induced oscillation issues and to design optimal STATCOMs' control for dampening these oscillation issues in a multi-IBR system due to complex system dynamics and varying operating conditions. To tackle these challenges, this paper proposes a novel method to reveal how STATCOMs influence IBR-induced oscillation issues in a multi-IBR system from the viewpoint of grid strength, which can consider varying operating conditions. Based on this proposed method, critical operating conditions are identified, wherein the system tends to be most unstable. Moreover, we demonstrate that robust small-signal stability issues of the multi-IBR system with STATCOMs can be simplified as that of multiple subsystems under critical operating conditions, which avoids exhaustive studies on many operating conditions with detailed system models. On this basis, an adaptive control-parameter design method is proposed for STATCOMs to ensure system robust stability under varying operating conditions. The proposed methods are validated by a modified IEEE39-node test system.

eess.SY↗

arXiv2022

Efficient Reinforcement Learning Through Trajectory Generation

A key barrier to using reinforcement learning (RL) in many real-world applications is the requirement of a large number of system interactions to learn a good control policy. Off-policy and Offline RL methods have been proposed to reduce the number of interactions with the physical environment by learning control policies from historical data. However, their performances suffer from the lack of exploration and the distributional shifts in trajectories once controllers are updated. Moreover, most RL methods require that all states are directly observed, which is difficult to be attained in many settings. To overcome these challenges, we propose a trajectory generation algorithm, which adaptively generates new trajectories as if the system is being operated and explored under the updated control policies. Motivated by the fundamental lemma for linear systems, assuming sufficient excitation, we generate trajectories from linear combinations of historical trajectories. For linear feedback control, we prove that the algorithm generates trajectories with the exact distribution as if they are sampled from the real system using the updated control policy. In particular, the algorithm extends to systems where the states are not directly observed. Experiments show that the proposed method significantly reduces the number of sampled data needed for RL algorithms.

cs.LG↗

arXiv2022

Robust and Kernelized Data-Enabled Predictive Control for Nonlinear Systems

This paper presents a robust and kernelized data-enabled predictive control (RoKDeePC) algorithm to perform model-free optimal control for nonlinear systems using only input and output data. The algorithm combines robust predictive control and a non-parametric representation of nonlinear systems enabled by regularized kernel methods. The latter is based on implicitly learning the nonlinear behavior of the system via the representer theorem. Instead of seeking a model and then performing control design, our method goes directly from data to control. This allows us to robustify the control inputs against the uncertainties in data by considering a min-max optimization problem to calculate the optimal control sequence. We show that by incorporating a proper uncertainty set, this min-max problem can be reformulated as a nonconvex but structured minimization problem. By exploiting its structure, we present a projected gradient descent algorithm to effectively solve this problem. Finally, we test the RoKDeePC on two nonlinear example systems - one academic case study and a grid-forming converter feeding a nonlinear load - and compare it with some existing nonlinear data-driven predictive control methods.

eess.SY↗

arXiv2021

Decentralized Data-Enabled Predictive Control for Power System Oscillation Damping

We employ a novel data-enabled predictive control (DeePC) algorithm in voltage source converter (VSC) based high-voltage DC (HVDC) stations to perform safe and optimal wide-area control for power system oscillation damping. Conventional optimal wide-area control is model-based. However, in practice detailed and accurate parametric power system models are rarely available. In contrast, the DeePC algorithm uses only input/output data measured from the unknown system to predict the future trajectories and calculate the optimal control policy. We showcase that the DeePC algorithm can effectively attenuate inter-area oscillations even in the presence of measurement noise, communication delays, nonlinear loads and uncertain load fluctuations. We investigate the performance under different matrix structures as data-driven predictors. Furthermore, we derive a novel Min-Max DeePC algorithm to be applied independently in multiple VSC-HVDC stations to mitigate inter-area oscillations, which enables decentralized and robust optimal wide-area control. Further, we discuss how to relieve the computational burden of the Min-Max DeePC by reducing the dimension of prediction uncertainty and how to leverage disturbance feedback to reduce the conservativeness of robustification. We illustrate our results with high-fidelity, nonlinear, and noisy simulations of a four-area test system.

eess.SY↗

arXiv2021

Robust Data-Enabled Predictive Control: Tractable Formulations and Performance Guarantees

We introduce a general framework for robust data-enabled predictive control (DeePC) for linear time-invariant (LTI) systems. The proposed framework enables us to obtain model-free optimal control for LTI systems based on noisy input/output data. More specifically, robust DeePC solves a min-max optimization problem to compute the optimal control sequence that is resilient to all possible realizations of the uncertainties in the input/output data within a prescribed uncertainty set. We present computationally tractable reformulations of the min-max problem with various uncertainty sets. Furthermore, we show that even though an accurate prediction of the future behavior is unattainable in practice due to inaccessibility of the perfect input/output data, the obtained robust optimal control sequence provides performance guarantees for the actually realized input/output cost. We further show that the robust DeePC generalizes and robustifies the regularized DeePC (with quadratic regularization or 1-norm regularization) proposed in the literature. Finally, we demonstrate the performance of the proposed robust DeePC algorithm on high-fidelity, nonlinear, and noisy simulations of a grid-connected power converter system.

eess.SY↗

arXiv2021

Quadratic Regularization of Data-Enabled Predictive Control: Theory and Application to Power Converter Experiments

Data-driven control that circumvents the process of system identification by providing optimal control inputs directly from system data has attracted renewed attention in recent years. In this paper, we focus on understanding the effects of the regularization on the data-enabled predictive control (DeePC) algorithm. We provide theoretical motivation and interpretation for including a quadratic regularization term. Our analysis shows that the quadratic regularization term leads to robust and optimal solutions with regards to disturbances affecting the data. Moreover, when the input/output constraints are inactive, the quadratic regularization leads to a closed-form solution of the DeePC algorithm and thus enables fast calculations. On this basis, we propose a framework for data-driven synchronization and power regulations of power converters, which is tested by high-fidelity simulations and experiments.

eess.SY↗

arXiv2021

Nodal Frequency Performance of Power Networks

This paper investigates how a disturbance in the power network affects the nodal frequencies of certain network buses. To begin with, we show that the inertia of a single generator is in inverse proportion to the initial rate of change of frequency (RoCoF) under disturbances. Then, we present how the initial RoCoF of the nodal frequencies are related to the inertia constants of multiple generators in a power network, which leads to a performance metric to analyze nodal frequency performance. To be specific, the proposed metric evaluates the impact of disturbances on the nodal frequency performance. The validity and effectiveness of the proposed metric are illustrated via simulations on a multi-machine power system.

eess.SY↗

arXiv2021

Placing Grid-Forming Converters to Enhance Small Signal Stability of PLL-Integrated Power Systems

The modern power grid features the high penetration of power converters, which widely employ a phase-locked loop (PLL) for grid synchronization. However, it has been pointed out that PLL can give rise to small-signal instabilities under weak grid conditions. This problem can be potentially resolved by operating the converters in grid-forming mode, namely, without using a PLL. Nonetheless, it has not been theoretically revealed how the placement of grid-forming converters enhances the small-signal stability of power systems integrated with large-scale PLL-based converters. This paper aims at filling this gap. Based on matrix perturbation theory, we explicitly demonstrate that the placement of grid-forming converters is equivalent to increasing the power grid strength and thus improving the small-signal stability of PLL-based converters. Furthermore, we investigate the optimal locations to place grid-forming converters by increasing the smallest eigenvalue of the weighted and Kron-reduced Laplacian matrix of the power network. The analysis in this paper is validated through high-fidelity simulation studies on a modified two-area test system and a modified 39-bus test system. This paper potentially lays the foundation for understanding the interaction between PLL-based (i.e., grid-following) converters and grid-forming converters, and coordinating their placements in future converter-dominated power systems.

eess.SY↗

arXiv2020

Generalized Short Circuit Ratio for Grid Strength Assessment in Inhomogeneous Multi-infeed LCC-HVDC Systems

Generalized short circuit ratio (gSCR) for gird strength assessment of multi-infeed high voltage direct current (MIDC) systems is a rigorous theoretical extension of traditional short circuit ratio (SCR), which allows the considerable experience of using SCR to be extended to MIDC systems. However, gSCR was originally derived based on the assumption of homogeneous MIDC systems, where all HVDC converters have an identical control configuration, which poses challenges to the applications of gSCR to inhomogeneous MIDC systems. To weaken this assumption, this letter applies modal perturbation theory to explore the possibility of applying gSCR in inhomogeneous MIDC systems. Results of numerical experiments show that, in inhomogeneous MIDC systems, the previously proposed gSCR can still be used without modification, but critical gSCR (CgSCR) needs to be redefined by considering the characteristics of HVDC converter control configurations. Accordingly, the difference between gSCR and redefined CgSCR can effectively quantify the pertinent ac grid strength in terms of static voltage stability margin. The performance of our proposed method is demonstrated in a triple-infeed inhomogeneous LCC-HVDC system.

eess.SY↗

arXiv2020

$H_{\infty}$-Control of Grid-Connected Converters: Design, Objectives and Decentralized Stability Certificates

The modern power system features high penetration of power converters due to the development of renewables, HVDC, etc. Currently, the controller design and parameter tuning of power converters heavily rely on rich engineering experience and extrapolation from a single converter system, which may lead to inferior performance or even instabilities under variable grid conditions. In this paper, we propose an $H_{\infty}$-control design framework to provide a systematic way for the robust and optimal control design of power converters. We discuss how to choose weighting functions to achieve anticipated and robust performance with regards to multiple control objectives. Further, we show that by a proper choice of the weighting functions, the converter can be conveniently specified as grid-forming or grid-following in terms of small-signal dynamics. Moreover, this paper first proposes a decentralized stability criterion based on the small gain theorem, which enables us to guarantee the global small-signal stability of a multi-converter system through local control design of the power converters. We provide high-fidelity nonlinear simulations and hardware-in-the-loop (HIL) real-time simulations to illustrate the effectiveness of our method.

eess.SY↗

arXiv2019

Impacts of Grid Structure on PLL-Synchronization Stability of Converter-Integrated Power Systems

Small-signal instability of grid-connected power converters may arise when the converters use a phase-locked loop (PLL) to synchronize with a weak grid. Commonly, this stability problem (referred as PLL-synchronization stability in this paper) was studied by employing a single-converter system connected to an infinite bus, which however, omits the impacts of power grid structure and the interactions among multiple converters. Motivated by this, we investigate how the grid structure affects PLL-synchronization stability of multi-converter systems. By using Kron reduction to eliminate the interior nodes, an equivalent reduced network is obtained which contains only the converter nodes. We explicitly show how the Kron-reduced multi-converter system can be decoupled into its modes. This modal representation allows us to demonstrate that the smallest eigenvalue of the grounded Laplacian matrix of the Kron-reduced network dominates the stability margin. We also carry out a sensitivity analysis of this smallest eigenvalue to explore how a perturbation in the original network affects the stability margin. On this basis, we provide guidelines on how to improve the PLL-synchronization stability of multi-converter systems by PLL-retuning, proper placement of converters or enhancing some weak connection in the network. Finally, we validate our findings with simulation results based on a 39-bus test system.

eess.SY↗

arXiv2019

Data-Enabled Predictive Control for Grid-Connected Power Converters

We apply a novel data-enabled predictive control (DeePC) algorithm in grid-connected power converters to perform safe and optimal control. Rather than a model, the DeePC algorithm solely needs input/output data measured from the unknown system to predict future trajectories. We show that the DeePC can eliminate undesired oscillations in a grid-connected power converter and stabilize an unstable system. However, the DeePC algorithm may suffer from poor scalability when applied in high-order systems. To this end, we present a finite-horizon output-based model predictive control (MPC) for grid-connected power converters, which uses an N-step auto-regressive-moving-average (ARMA) model for system representation. The ARMA model is identified via an N-step prediction error method (PEM) in a recursive way. We investigate the connection between the DeePC and the concatenated PEM-MPC method, and then analytically and numerically compare their closed-loop performance. Moreover, the PEM-MPC is applied in a voltage source converter based HVDC station which is connected to a two-area power system so as to eliminate low-frequency oscillations. All of our results are illustrated with high-fidelity, nonlinear, and noisy simulations.

eess.SY↗