Searcharxiv⌕ Search

arXiv subjects

Lucio Isa

Publications and source records attributed to Lucio Isa.

At least 19 recordsLinked to original sources

Model-free stiffness measurement of microscale soft contacts by far-field traction force microscopy

The microscale stiffness of soft materials governs their contact mechanics, adhesion and friction, yet it is surprisingly difficult to measure. Micro or nanoindentation is typically used, but extracting stiffness from these measurements requires using contact mechanics models (e.g. JKR), whose assumptions often break down for soft adhesive contacts. Here, we introduce far-field traction force microscopy (FF-TFM) to extract stiffness without using any contact model. We drag a colloidal probe mounted on an atomic-force microscope across a soft surface, measuring the friction force while imaging the displacements of fluorescent tracers on the substrate. Far from the contact, in the elastic limit, these lateral displacements depend solely on the friction force and the substrate stiffness, and fitting them with the point-force solution thus gives the substrate's Young's modulus directly. We successfully match bulk rheology moduli with FF-TFM for six different silicone elastomers, where JKR fits to indentation data underestimate moduli by as much as 40\% of their bulk values. Our approach also enables tracking how the probe slips across the surface. We find that soft contacts can "pre-slip" with no detectable signature in the force signal, unlike stiffer contacts. FF-TFM thus offers a contact-model-free route to measuring microscale stiffness and slip behavior in soft materials.

cond-mat.soft↗

Delay-induced current reversal in traveling activity waves

Self-propelled particles that regulate their speed based on a response to a local activity source can move with or against a traveling wave of that source depending on their response time. Silica-titania Janus microswimmers, whose UV-controlled speed relaxes with a delay intrinsic to the titania photoconductivity adaptation, carry two independent memory channels: the familiar directional memory dictated by persistent active Brownian motion, and a distinct memory from the speed adaptation. Combining experiments, Langevin simulations, and a moment expansion of the corresponding Fokker-Planck equation, we show that this delayed response to speed adaptation reshapes transport under traveling UV-illumination waves and can even reverse it relative to the direction set by orientational memory alone. In particular, we observe that delay promotes transport in the direction opposite to the traveling activity waves, where, beyond a critical value, the particle current reverses with respect to the wave propagation direction. Crucially, this behavior requires an asymmetric response to the speed adaptation, with an instantaneous rise but a delayed fall upon exposure to time-varying UV light. Theory further shows that this phenomenology is specific to the response asymmetry rather than to the mere presence of a delay, i.e. reversing the asymmetry reverses the effect of the delay on the particle current relative to the wave. We thus establish propulsion-delay asymmetry as a control parameter for directed transport of responsive active particles in traveling activity landscapes.

cond-mat.soft↗

Extracting hydrogel properties by watching hydrogel particles moving through solid ice

Strikingly, when hydrogel particles are embedded in ice in a temperature gradient, they move through the solid ice towards warmer temperatures, while swelling as they warm up. This motion comes from a flow of unfrozen water through the hydrogel mesh, driven by a process known as `cryosuction'. Here, we show how one can use this behavior to measure -- with extremely high resolution -- a range of different hydrogel transport properties, and how these change as a hydrogel deswells. These properties include permeability, compressibility, and poroelastic diffusivity: all of which are challenging to measure, but widely important for phenomena involving swelling, dehydration, transpiration and filtration. We demonstrate the measurement technique using poly(ethylene glycol) diacrylate (PEGDA) hydrogels. The technique uses picoliter-scale hydrogel volumes, and yields measurements of hydrogel properties that are consistent with existing literature data. The high resolution of our measurements also allows us to test commonly-used, classical predictions for hydrogel properties (derived assuming an idealized, homogeneous polymer network in the hydrogel). We show that these classical predictions do not work well, highlighting the need for new models that can accurately describe real hydrogels.

cond-mat.soft↗

IceCAPA: patterning particles and microorganisms at a freezing front

The ability to precisely pattern micro- and nano-scale objects on surfaces is important for a range of different applications. For example, colloidal patterning has been used to create plasmonic surfaces, light-emitting diodes or authentication marks, while microbial cell patterning can be applied to screening antibiotic response and cellular interactions over larger populations at the single-cell level. However, we still lack versatile techniques that can pattern a wide range of synthetic and biological objects on a spectrum of different substrate types. Here, we present a robust patterning technique based on the directional freezing of a particle or bacterial suspension over a patterned substrate. Growing ice pushes the desired objects into traps in the substrate, while sweeping away non-trapped ones, leaving behind high-fidelity patterns. We show that this method works for a range of different materials (both synthetic particles and microbial cells), and is unaffected by substrate wettability. Furthermore, patterned bacterial cells retain excellent post-assembly viability, highlighting the gentle nature of the assembly technique. Beyond patterning applications, our results also give insights into processes involving the freezing of particulate suspensions. In particular, we demonstrate the importance of the temperature gradient as a key control which determines how particles interact with freezing fronts. Finally, we highlight a tight analogy between particles interacting with a freezing front and with air-water interfaces, suggesting that results from capillarity may shed light on freezing phenomena.

cond-mat.soft↗

Resolving Light-Induced Structural Rearrangements in Responsive Microgels

Optically-responsive microgels offer a versatile platform for designing adaptive soft materials with coupled light and thermal responsiveness. Control over the crosslinking degree is particularly appealing as it can regulate not only particle size but also stiffness, thereby enabling remote tuning of key material functionalities. However, the internal structural changes that couple molecular photoresponsive mechanisms to mesoscopic properties remain poorly resolved. Here, we investigate different light-responsive microgels containing covalently incorporated coumarin moieties, which impart optical sensitivity through UV-induced cycloaddition, by combining dynamic light scattering, small-angle neutron scattering, and molecular dynamics simulations. We show that light irradiation alters not only particle size but also the internal polymer density distribution and subsequent thermal response. Before irradiation, the microgels exhibit a star-like architecture with a dense core and extended polymeric arms. After irradiation, the network evolves toward a markedly more compact structure. This transformation cannot be rationalized simply as an equivalent to an increase in crosslinking density during synthesis, as observed in the thermal response, revealing light as a powerful tool to regulate microgel architecture and multifunctional responsiveness.

cond-mat.soft↗

Universal transport of active colloids with sensory delay in motility landscapes

We experimentally, numerically and analytically explore the diffusive transport of active colloidal particles with sensory delay, navigating motility landscapes in which the self-propulsion speed depends on space. We show how the transport properties can be obtained by replacing the space dependence of the self-propulsion speed by a dynamical stochastic switching process in the absence of delay, and extend the theory for systems with finite delayed responses. We obtain analytical results for the mean square displacement and the effective diffusion coefficient which accurately predict experimental measurements and numerical simulations across multiple scales. We show how, within the regime of validity of the delay-extended theory, density patterns and effective diffusion obey universal scaling forms. Our work provides minimal framework describing the transport properties of active swimmers with internal adaptation dynamics in motility landscapes.

cond-mat.stat-mech↗

Shaping nematic order in bacterial films with single-cell resolution patterning

Bacterial colonies composed of elongated cells form active nematic fluids that spontaneously self-organise into ordered domains of aligned cells and exhibit self-generated chaotic flows powered by cell growth. While their dynamics have attracted significant attention, the role of initial conditions remains largely unexplored due to a lack of precise patterning methods. Here, we harness the precision of capillary assembly to pattern Bacillus subtilis endospores into arrays with controlled positions and orientations at single-cell resolution. Upon germination and growth of cell chains, we quantify the dynamics and morphologies of the resulting bacterial films. While orthogonally seeded spores lead to chaotic dynamics, seeding them with parallel orientations yields films with high nematic order across millimetres, which subsequently synchronously buckle upon further growth. Our observations are captured by numerical simulations and a model that describes the buckling dynamics starting from the mechanical properties of individual filaments. By programming local cell orientation with single-cell precision, we finally harness nematic alignment to create macroscopic bacterial films with local optical anisotropy, via structural colouration and light polarisation. Our findings demonstrate that initial conditions play a key role and offer exciting opportunities to control the spatio-temporal organization of bacterial assemblies towards addressing open biological questions and realizing living materials with tailored properties.

physics.bio-ph↗

Label-free quantitative imaging of two-dimensional concentration gradients using Fabry-Pérot interferometry

Concentration gradients at the microscale play a central role in many physical, chemical, and biological systems, yet their quantitative visualization remains challenging due to the limited optical contrast associated with changes in concentration. Here, we present RIO (the Refractive Index Observer), a label-free interferometric tool for quantitative imaging of refractive index, and thus concentration fields in microfluidic systems. Implemented using a Fabry-Pérot microfluidic chip mounted on a standard optical microscope, RIO achieves a per-pixel refractive index precision on the order of $1\times 10^{-5}$ refractive index units (RIU) using a standard CMOS camera, enabling high sensitivity two-dimensional chemical imaging. We Characterize the refractive index resolution and spatiotemporal performance of the instrument and demonstrate its capabilities by measuring concentration gradients of dissolved NaCl in a co-laminar flow. RIO provides an accessible, label-free platform for quantitative studies of microscale concentration fields in systems where molecular labeling is undesirable or impractical, and enables investigations of a broad range of out-of-equilibrium phenomena, from polymerization and enzymatic reactions to cell signaling and electrochemical processes.

physics.optics↗

Controlling polymerization-induced phase separation in the synthesis of porous gels

Porous gels -- gels with solvent-filled pores that are much larger than their mesh size -- are widely used in engineering and biomedical applications due to their tunable mechanics, high water content, and selective permeability. Among various strategies to create porous gels, polymerization-induced phase separation (PIPS) has shown particular promise. However, the conditions that trigger and control PIPS remain poorly understood. Here, we systematically investigate the influence of solvent quality, polymeric precursor molecular weight, and polymer concentration on phase separation in polymerizing poly(ethylene glycol) diacrylate gels. We find that phase separation occurs when the precursor solution concentration is below the overlap concentration. Phase-separated gels have a pore geometry that is controlled by solvent quality: better solvents result in smaller pores, while worse solvents can create superporous, highly-absorbant gels. Motivated by our results, we propose a theory that predicts when phase separation occurs in polymerizing gels, applicable across a wide range of polymer/solvent gel systems. Our results provide a framework for the rational design of porous gels.

cond-mat.soft↗

Segregation and cooperation in active colloidal binary mixtures

The complex interactions underlying collective motion in biological systems give rise to emergent behaviours such as flocking, sorting, and cooperative transport. These dynamics often involve species with different motilities coordinating movement to optimize navigation and survival. Synthetic analogues based on active colloids offer a controlled platform to explore such behaviours, yet most experimental realizations remain limited to monodisperse systems or mixtures of passive and active particles. Here, we investigate dense binary mixtures of active Janus colloids with distinct motilities and independently tunable alignment, actuated by AC electric fields. We demonstrate experimentally and numerically that both species form highly dynamic polar clusters, with alignment emerging independently of propulsion speed. In mixed populations, interspecies interactions lead to effective segregation and cooperative motion, including transient enhancement of slower particle motility. Our results reveal how motility contrast and alignment combine to drive self-organization in active mixtures, offering strategies for designing reconfigurable materials with collective functionalities.

cond-mat.soft↗

Density modulations in active colloidal systems through orthogonal propulsion control and sensory delays

Recent advancements in active colloidal systems aim to mimic key characteristics of biological microswimmers, particularly their adaptive motility in response to environmental changes. While many approaches rely on externally imposing a propulsive force, achieving true autonomous and self-regulating adaptation to the environment remains limited. In this study, we develop and analyze Janus microswimmers driven by electrohydrodynamic flows that autonomously adjust their propulsion dynamics in response to varying illumination conditions. Our Janus particles are silica colloids partially coated with titania, which self-propel via induced-charge electrophoresis (ICEP) under uniform AC electric fields. Since titania is photoconductive, it increases its conductivity under UV illumination, which thereby regulates the propulsion velocity independently of and orthogonally to the applied electric field. Crucially, the velocity adaptation requires a finite time. This sensory delay, which we systematically characterize, leads to enhanced microswimmer localization in response to spatiotemporal light modulations compared to the typical case of instantaneous response considered for synthetic microswimmers. By harnessing these dynamics, akin to those of biological microswimmers, we exert precise control over both local and global particle behavior, presenting novel opportunities for adaptive active matter systems.

cond-mat.soft↗

Gating and tunable confinement of active colloids within patterned environments

Active colloidal particles typically exhibit a pronounced affinity for accumulating and being captured at boundaries. Here, we engineer long-range repulsive interactions between colloids that self-propel under an electric field and patterned obstacles. As a result of these interactions, particles turn away from obstacles and avoid accumulation. We show that by tuning the applied field frequency, we precisely and rapidly control the effective size of the obstacles and therefore modulate the particle approach distance. This feature allows us to achieve gating and tunable confinement of our active particles whereby they can access regions between obstacles depending on the applied field. Our work provides a versatile means to directly control confinement and organization, paving the way towards applications such as sorting particles based on motility or localizing active particles on demand.

cond-mat.soft↗

Self-reconfiguring colloidal active matter

Cells and microorganisms employ dynamic shape changes to enable steering and avoidance for efficient spatial exploration and collective organization. In contrast, active colloids, their synthetic counterparts, currently lack similar abilities and strategies. Through physical interactions alone, here we create active colloidal molecules that spontaneously reconfigure their structure, unlike traditional active particles. We find that self-reconfiguration decouples reorientational dynamics from rotational diffusivity and bestows our active molecules additional reorientation capabilities. During encounters with neighbors, rapid conformational changes lead to self-steering and avoidance. At higher area fractions, reconfiguration-induced avoidance fully inhibits characteristic dynamic clustering, motility-induced phase separation and flocking; instead, the system retains a homogeneous structure comprising well-separated active units. Self-reconfiguring systems therefore present an exciting path towards autonomous motion beyond that of classical synthetic active matter.

cond-mat.soft↗

Tunable Assembly of Confined Janus Microswimmers in Sub-kHz Electic Fields under Gravity

Active systems comprising micron-sized self-propelling units, also termed microswimmers, are promising candidates for the bottom-up assembly of small structures and reconfigurable materials. Here we leverage field-driven colloidal assembly to induce structural transformations in dense layers of microswimmers driven by an alternating current (AC) electric field and confined in a microfabricated trap under the influence of gravity. By varying the electric field frequency, we realize significant structural transformations, from a gas-like state at high frequencies to dynamically rearranging dense crystalline clusters at lower frequencies, characterized by vorticity in their dynamics. We demonstrate the ability to switch between these states on-demand, showing that the clustering mechanism differs from motility-induced phase separation. Our results offer a valuable framework for designing high-density active matter systems with controllable structural properties, envisioned to advance the development of artificial materials with self-healing and reconfiguration capabilities.

cond-mat.soft↗

Sliding or Rolling? Characterizing single-particle contacts

Contacts between particles in dense, sheared suspensions are believed to underpin much of their rheology. Roughness and adhesion are known to constrain the relative motion of particles, and thus globally affect the shear response, but an experimental description of how they microscopically influence the transmission of forces and relative displacements within contacts is lacking. Here we show that an innovative colloidal-probe atomic force microscopy technique allows the simultaneous measurement of normal and tangential forces exchanged between tailored surfaces and microparticles while tracking their relative sliding and rolling, unlocking the direct measurement of coefficients of rolling friction, as well as of sliding friction. We demonstrate that, in the presence of sufficient traction, particles spontaneously roll, reducing dissipation and promoting longer-lasting contacts. Conversely, when rolling is prevented, friction is greatly enhanced for rough and adhesive surfaces, while smooth particles coated by polymer brushes maintain well-lubricated contacts. We find that surface roughness induces rolling due to load-dependent asperity interlocking, leading to large off-axis particle rotations. In contrast, smooth, adhesive surfaces promote rolling along the principal axis of motion. Our results offer direct values of friction coefficients for numerical studies and an interpretation of the onset of discontinuous shear thickening based on them, opening up new ways to tailor rheology via contact engineering.

cond-mat.soft↗

The 2024 Motile Active Matter Roadmap

Activity and autonomous motion are fundamental aspects of many living and engineering systems. Here, the scale of biological agents covers a wide range, from nanomotors, cytoskeleton, and cells, to insects, fish, birds, and people. Inspired by biological active systems, various types of autonomous synthetic nano- and micromachines have been designed, which provide the basis for multifunctional, highly responsive, intelligent active materials. A major challenge for understanding and designing active matter is their inherent non-equilibrium nature due to persistent energy consumption, which invalidates equilibrium concepts such as free energy, detailed balance, and time-reversal symmetry. Furthermore, interactions in ensembles of active agents are often non-additive and non-reciprocal. An important aspect of biological agents is their ability to sense the environment, process this information, and adjust their motion accordingly. It is an important goal for the engineering of micro-robotic systems to achieve similar functionality. With many fundamental properties of motile active matter now reasonably well understood and under control, the ground is prepared for the study of physical aspects and mechanisms of motion in complex environments, of the behavior of systems with new physical features like chirality, of the development of novel micromachines and microbots, of the emergent collective behavior and swarming of intelligent self-propelled particles, and of particular features of microbial systems. The vast complexity of phenomena and mechanisms involved in the self-organization and dynamics of motile active matter poses major challenges, which can only be addressed by a truly interdisciplinary effort involving scientists from biology, chemistry, ecology, engineering, mathematics, and physics.

cond-mat.soft↗

Characterizing hydrogel behavior under compression with gel-freezing osmometry

Hydrogels are particularly versatile materials that are widely found in both Nature and industry. One key reason for this versatility is their high water content, which lets them dramatically change their volume and many of their mechanical properties -- often by orders of magnitude -- as they swell and dry out. Currently, we lack techniques that can precisely characterize how these properties change with water content. To overcome this challenge, here we develop Gel-Freezing Osmometry (GelFrO): an extension of freezing-point osmometry. We show how GelFrO can measure a hydrogel's mechanical response to compression and osmotic pressure, while only using small, $O(100μ$L$)$ samples. Because the technique allows measurement of properties over an unusually wide range of water contents, it allows us to accurately test theoretical predictions. We find simple, power-law behavior for both mechanical response to compression, and osmotic pressure, while these are not well-captured by classical Flory-Huggins theory. We interpret this power-law behavior as a hallmark of a microscopic fractal structure of the gel's polymer network, and propose a simple way to connect the gel's fractal dimension to its mechanical and osmotic properties. This connection is supported by observations of hydrogel microstructures using small-angle x-ray scattering. Finally, our results motivate us to propose an updated constitutive model describing hydrogel swelling, and mechanical response.

cond-mat.soft↗

Simulation and time series analysis of responsive active Brownian particles (rABPs) with memory

To realise the goals of active matter at the micro- and nano-scale, the next generation of microrobots must be capable of autonomously sensing and responding to their environment to carry out pre-programmed tasks. Memory effects are proposed to have a significant effect on the dynamics of responsive robotic systems, drawing parallels to strategies used in nature across all length-scales. Inspired by the integral feedback control mechanism by which E.coli are proposed to sense their environment, we develop a numerical responsive active Brownian particle (rABP) model in which the rABPs continuously react to changes in the physical parameters dictated by their local environment. The resulting generated time series are then used to classify and characterise their response, leading to the identification of conditional heteroscedasticity in their physics. We then train recurrent neural networks (RNNs) capable of quantitatively describing the responsiveness of rABPs using their 2-D trajectories. We believe that our proposed strategy to determine the parameters governing the dynamics of rABPs can be applied to guide the design of microrobots with physical intelligence encoded during their fabrication.

cond-mat.soft↗