arXiv subjects

Ludvig Edman

Publications and source records attributed to Ludvig Edman.

5 recordsLinked to original sources

arXiv2026

Modifying Electrochemical Doping in Light-Emitting Electrochemical Cells with Gold Nanoparticles

Electrochemical doping offers dynamic control of the electronic properties of organic semiconductors, and it is the enabling feature of a range of technologies, including electrochemical transistors, energy-storage devices, light-emitting electrochemical cells (LECs), and bioelectronics. Electrochemical doping is commonly controlled by the selection of the constituents in the active material of the device or the applied voltage bias, but herein we report that the incorporation of Au nanoparticles (Au-NPs) at an electrode interface can constitute an alternative control parameter. The LEC features balanced p- and n-type electrochemical doping that forms a p-n junction doping structure in its active material, and we find that it is possible to reshape this doping profile by incorporating Au-NPs at an electrode interface. Specifically, we establish that the inclusion of neat non-capped Au-NPs at the anodic interface shifts the p-n junction (i.e., the emission zone) away from the anode. In contrast, the inclusion of Au-NPs capped with sodium citrate is found to reverse this behavior, so that the emission zone is instead moved towards the anode. We utilize this control parameter to shift the emission zone towards a position of constructive (destructive) interference, as manifested in a strong increase (decrease) of the LEC emission efficiency. Our findings establish an interfacial strategy for modulating the spatial profile of electrochemical doping and tuning device performance without altering the chemistry of the active material, relying instead on the surface modification of one electrode. This approach is important because it provides a versatile and minimally invasive route to optimize electrochemical devices while preserving the intrinsic properties and formulation of the active material.

cond-mat.mtrl-sci↗

arXiv2026

Round-Robin Test of a Light-Emitting Electrochemical Cell: Establishing a Reference Protocol for Quality Research

Emerging technologies benefit from a jointly established reference protocol, which can lower the bar of entry for new researchers while serving as a calibration standard for established actors. The light-emitting electrochemical cell (LEC) combines electrochemistry and optoelectronics in an intricate manner, and it can by that enable sustainable and commercially relevant printing fabrication of emissive thin-film devices. However, LEC performance is sensitive to a range of material and processing parameters, which frequently results in inadequate, or even erroneous, device evaluation. With this in mind, we present herein a LEC reference protocol, which details the sourcing of materials and the procedures and parameters for robust device fabrication and operation. The protocol has been tested across nine international research groups, and the collected results from this interlaboratory round-robin test confirm that good LEC performance can be reproducibly obtained following our protocol. We also identify common pitfalls that can arise during LEC development, and present practical steps for attaining optimum LEC performance. We hope this reference protocol will improve the quality of future LEC research and serve as a guide for future researchers entering this vibrant field.

cond-mat.soft↗

arXiv2025

In-operando dipole orientation for bipolar injection from air-stable electrodes into organic semiconductors

Efficient charge-carrier injection from air-stable electrodes into organic semiconductors (OSCs) is essential for fabricating solution-processed organic optoelectronic devices under ambient conditions. Today, this is typically achieved by incorporating doped OSC interlayers, introducing self-assembled dipole monolayers, or adding mobile ions to the active material (AM). Here, we demonstrate an alternative approach that eliminates the need for additional injection layers or ionic additives. We achieve this by blending the dipolar compound TMPE-OH into the electroluminescent polymer Super Yellow (SY) and depositing this sole AM between two air-stable electrodes, forming a single-layer, dipole-doped OLED (D-OLED). By tracking its transient voltage-luminance response, performing impedance spectroscopy, and comparing these characteristics with two other single-layer device concepts, i.e. a neat-SY OLED without a dipolar compound and a light-emitting electrochemical cell (LEC) containing mobile ions, we can establish that the auxiliary dipoles in the D-OLED reorient under the applied driving voltage, enabling immediate luminance turn-on and lowering the injection barriers at both electrodes. Finally, we demonstrate that the D-OLED achieves current efficacies comparable to those of SY OLEDs incorporating dedicated injection layers or LECs. Our study establishes dipolar doping as a practical strategy for efficient bipolar charge injection from air-stable electrodes in solution-processed organic semiconductor devices.

cond-mat.mtrl-sci↗

arXiv2024

Impact of the electrode material on the performance of light-emitting electrochemical cells

Light-emitting electrochemical cells (LECs) are promising candidates for fully solution-processed lighting applications because they can comprise a single active-material layer and air-stable electrodes. While their performance is often claimed to be independent of the electrode material selection due to the in-situ formation of electric double layers (EDLs), we demonstrate conceptually and experimentally that this understanding needs to be modified. Specifically, the exciton generation zone is observed to be affected by the electrode work function. We rationalize this finding by proposing that the ion concentration in the injection-facilitating EDLs depends on the offset between the electrode work function and the respective semiconductor orbital, which in turn influences the number of ions available for electrochemical doping and hence shifts the exciton generation zone. Further, we investigate the effects of the electrode selection on exciton losses to surface plasmon polaritons and discuss the impact of cavity effects on the exciton density. We conclude by showing that the measured electrode-dependent LEC luminance transients can be replicated by an optical model that considers these electrode-dependent effects to calculate the attained light outcoupling of the LEC stack. As such, our findings provide rational design criteria considering the electrode materials, the active-material thickness, and its composition in concert to achieve optimum LEC performance.

physics.optics↗

arXiv2021

Magnetically collected platinum/nickel alloy nanoparticles -- insight into low noble metal content catalysts for hydrogen evolution reaction

The hydrogen evolution reaction (HER) is a key process in electrochemical water splitting. To lower the cost and environmental impact of this process, it is highly motivated to develop electrocatalysts with low or no content of noble metals. Here we report on a novel and ingenious synthesis of hybrid PtxNi1-x electrocatalysts in the form of a nanoparticle-necklace structure named nanotrusses, with very low noble metal content. The nanotruss structure possesses important features, such as good conductivity, high surface area, strong interlinking and substrate adhesion, which renders for an excellent HER activity. Specifically, the best performing Pt0.05Ni0.95 sample, demonstrates a Tafel slope of 30 mV dec-1 in 0.5 M H2SO4, and an overpotential of 20 mV at a current density of 10 mA cm-2 with high stability. The impressive catalytic performance is further rationalized in a theoretical study, which provides insight into the mechanism for how such small platinum content can allow for close-to-optimal adsorption energies for hydrogen.

cond-mat.mtrl-sci↗