arXiv subjects

Lukas Grünhaupt

Publications and source records attributed to Lukas Grünhaupt.

At least 19 recordsLinked to original sources

arXiv2025

An rf-SQUID-based traveling-wave parametric amplifier with -84 dBm input saturation power across more than one octave bandwidth

Traveling-wave parametric amplifiers (TWPAs) have become an essential tool for the readout of quantum circuits and the search for dark matter. We report on the implementation of an rf-SQUID-based Josephson TWPA with an average saturation power of -84 dBm, while providing an average power gain of 20 dB from 3.5 to 8.5 GHz. This wide bandwidth is enabled by reducing the curvature of the dispersion in the signal band while suppressing detrimental mixing processes. With 2393 rf-SQUIDs our device has a comparable number of nonlinear elements, but achieves ten times higher saturation power than previous works, showing that using rf-SQUIDs results in a more favorable trade-off between device length and saturation power. Harnessing wideband characterization techniques we determine the TWPA's excess noise above the quantum limit to be 0.8 to 1.5 photons. In addition, we validate signal-to-noise ratio improvement as a practical measure for tuning the TWPA to minimize the total system noise, and demonstrate that its optimum does not coincide with the highest gain.

quant-ph↗

arXiv2024

Demonstration of dual Shapiro steps in small Josephson junctions

Bloch oscillations in small Josephson junctions were predicted theoretically as the quantum dual to Josephson oscillations. A significant consequence of this prediction is the emergence of quantized current steps, so-called dual Shapiro steps, when synchronizing Bloch oscillations to an external microwave signal. These steps potentially enable a fundamental standard of current $I$, defined via the frequency $f$ of the external signal and the elementary charge $e$, $I=\pm n \times 2ef$, where $n$ is a natural number. Here, we realize this fundamental relation by synchronizing the Bloch oscillations in small Al/AlO$_\mathrm{x}$/Al Josephson junctions to sinusoidal drives with frequencies varying from $1$ to $6\:\mathrm{GHz}$ and observe dual Shapiro steps up to $I\approx 3 \: \mathrm{nA}$. Inspired by today's voltage standards and to further confirm the duality relation, we investigate a pulsed drive regime, which is dual to the single flux quantum mode of Josephson oscillations, and observe a similar asymmetric pattern of dual Shapiro steps. This work confirms quantum duality effects in Josephson junctions and paves the way towards a range of applications in quantum metrology based on well-established fabrication techniques and straightforward circuit design.

cond-mat.mes-hall↗

arXiv2023

Non-degenerate parametric amplifiers based on dispersion engineered Josephson junction arrays

Determining the state of a qubit on a timescale much shorter than its relaxation time is an essential requirement for quantum information processing. With the aid of a new type of non-degenerate parametric amplifier, we demonstrate the continuous detection of quantum jumps of a transmon qubit with 90% fidelity in state discrimination. Entirely fabricated with standard two-step optical lithography techniques, this type of parametric amplifier consists of a dispersion engineered Josephson junction (JJ) array. By using long arrays, containing $10^3$ JJs, we can obtain amplification at multiple eigenmodes with frequencies below $10~\mathrm{GHz}$, which is the typical range for qubit readout. Moreover, by introducing a moderate flux tunability of each mode, employing superconducting quantum interference device (SQUID) junctions, a single amplifier device could potentially cover the entire frequency band between 1 and $10~\mathrm{GHz}$.

quant-ph↗

arXiv2023

Implementation of a transmon qubit using superconducting granular aluminum

The high kinetic inductance offered by granular aluminum (grAl) has recently been employed for linear inductors in superconducting high-impedance qubits and kinetic inductance detectors. Due to its large critical current density compared to typical Josephson junctions, its resilience to external magnetic fields, and its low dissipation, grAl may also provide a robust source of non-linearity for strongly driven quantum circuits, topological superconductivity, and hybrid systems. Having said that, can the grAl non-linearity be sufficient to build a qubit? Here we show that a small grAl volume ($10 \times 200 \times 500 \,\mathrm{nm^3}$) shunted by a thin film aluminum capacitor results in a microwave oscillator with anharmonicity $α$ two orders of magnitude larger than its spectral linewidth $Γ_{01}$, effectively forming a transmon qubit. With increasing drive power, we observe several multi-photon transitions starting from the ground state, from which we extract $α= 2 π\times 4.48\,\mathrm{MHz}$. Resonance fluorescence measurements of the $|0> \rightarrow |1>$ transition yield an intrinsic qubit linewidth $γ= 2 π\times 10\,\mathrm{kHz}$, corresponding to a lifetime of $16\,\mathrm{μs}$. This linewidth remains below $2 π\times 150\,\mathrm{kHz}$ for in-plane magnetic fields up to $\sim70\,\mathrm{mT}$.

quant-ph↗

arXiv2023

Vulnerability to Parameter Spread in Josephson Traveling-Wave Parametric Amplifiers

We analyze the effect of circuit parameter variation on the performance of Josephson traveling-wave parametric amplifiers (JTWPAs). Specifically, the JTWPA concept we investigate is using flux-biased nonhysteretic rf-SQUIDs in a transmission line configuration, which harnesses the three-wave mixing (3WM) regime. Dispersion engineering enables phasematching to achieve power gain of $\sim$20 dB, while suppressing the generation of unwanted mixing processes. Two dispersion engineering concepts using a 3WM-JTWPA circuit model, i.e., resonant phase-matching (RPM) and periodic capacitance modulation (PCM), are discussed, with results potentially also applicable to four-wave-mixing (4WM) JTWPAs. We propose suitable circuit parameter sets and evaluate amplifier performance with and without circuit parameter variance using transient circuit simulations. This approach inherently takes into account microwave reflections, unwanted mixing products, imperfect phasematching, pump depletion, etc. In the case of RPM the resonance frequency spread is critical, while PCM is much less sensitive to parameter spread. We discuss degrees of freedom to make the JTWPA circuits more tolerant to parameter spread. Finally, our analysis shows that the flux-bias point where rf-SQUIDs exhibit Kerr-free nonlinearity is close to the sweet spot regarding critical current spread.

cond-mat.supr-con↗

arXiv2022

Gate-tunable kinetic inductance in proximitized nanowires

We report the detection of a gate-tunable kinetic inductance in a hybrid InAs/Al nanowire. For this purpose, we have embedded the nanowire into a quarter-wave coplanar waveguide resonator and measured the resonance frequency of the circuit. We find that the resonance frequency can be changed via the gate voltage that controls the electron density of the proximitized semiconductor and thus the nanowire inductance. Applying Mattis-Bardeen theory, we extract the gate dependence of the normal state conductivity of the nanowire, as well as its superconducting gap. Our measurements complement existing characterization methods for hybrid nanowires and provide a new and useful tool for gate-controlled superconducting electronics.

cond-mat.supr-con↗

arXiv2022

Spectroscopy of spin-split Andreev levels in a quantum dot with superconducting leads

We use a hybrid superconductor-semiconductor transmon device to perform spectroscopy of a quantum dot Josephson junction tuned to be in a spin-1/2 ground state with an unpaired quasiparticle. Due to spin-orbit coupling, we resolve two flux-sensitive branches in the transmon spectrum, depending on the spin of the quasi-particle. A finite magnetic field shifts the two branches in energy, favoring one spin state and resulting in the anomalous Josephson effect. We demonstrate the excitation of the direct spin-flip transition using all-electrical control. Manipulation and control of the spin-flip transition enable the future implementation of charging energy protected Andreev spin qubits.

cond-mat.mes-hall↗

arXiv2022

Direct manipulation of a superconducting spin qubit strongly coupled to a transmon qubit

Spin qubits in semiconductors are currently one of the most promising architectures for quantum computing. However, they face challenges in realizing multi-qubit interactions over extended distances. Superconducting spin qubits provide a promising alternative by encoding a qubit in the spin degree of freedom of an Andreev level. Such an Andreev spin qubit could leverage the advantages of circuit quantum electrodynamic, enabled by an intrinsic spin-supercurrent coupling. The first realization of an Andreev spin qubit encoded the qubit in the excited states of a semiconducting weak-link, leading to frequent decay out of the computational subspace. Additionally, rapid qubit manipulation was hindered by the need for indirect Raman transitions. Here, we exploit a different qubit subspace, using the spin-split doublet ground state of an electrostatically-defined quantum dot Josephson junction with large charging energy. Additionally, we use a magnetic field to enable direct spin manipulation over a frequency range of 10 GHz. Using an all-electric microwave drive we achieve Rabi frequencies exceeding 200 MHz. We furthermore embed the Andreev spin qubit in a superconducting transmon qubit, demonstrating strong coherent qubit-qubit coupling. These results are a crucial step towards a hybrid architecture that combines the beneficial aspects of both superconducting and semiconductor qubits.

quant-ph↗

arXiv2022

Mitigation of quasiparticle loss in superconducting qubits by phonon scattering

Quantum error correction will be an essential ingredient in realizing fault-tolerant quantum computing. However, most correction schemes rely on the assumption that errors are sufficiently uncorrelated in space and time. In superconducting qubits this assumption is drastically violated in the presence of ionizing radiation, which creates bursts of high energy phonons in the substrate. These phonons can break Cooper-pairs in the superconductor and, thus, create quasiparticles over large areas, consequently reducing qubit coherence across the quantum device in a correlated fashion. A potential mitigation technique is to place large volumes of normal or superconducting metal on the device, capable of reducing the phonon energy to below the superconducting gap of the qubits. To investigate the effectiveness of this method we fabricate a quantum device with four nominally identical nanowire-based transmon qubits. On the device, half of the niobium-titanium-nitride ground plane is replaced with aluminum (Al), which has a significantly lower superconducting gap. We deterministically inject high energy phonons into the substrate by voltage biasing a galvanically isolated Josephson junction. In the presence of the low gap material, we find a factor of 2-5 less degradation in the injection-dependent qubit lifetimes, and observe that undesired excited qubit state population is mitigated by a similar factor. We furthermore turn the Al normal with a magnetic field, finding no change in the phonon-protection. This suggests that the efficacy of the protection in our device is not limited by the size of the superconducting gap in the Al ground plane. Our results provide a promising foundation for protecting superconducting qubit processors against correlated errors from ionizing radiation.

quant-ph↗

arXiv2022

Singlet-doublet transitions of a quantum dot Josephson junction detected in a transmon circuit

We realize a hybrid superconductor-semiconductor transmon device in which the Josephson effect is controlled by a gate-defined quantum dot in an InAs/Al nanowire. Microwave spectroscopy of the transmon's transition spectrum allows us to probe the ground state parity of the quantum dot as a function of gate voltages, external magnetic flux, and magnetic field applied parallel to the nanowire. The measured parity phase diagram is in agreement with that predicted by a single-impurity Anderson model with superconducting leads. Through continuous time monitoring of the circuit we furthermore resolve the quasiparticle dynamics of the quantum dot Josephson junction across the phase boundaries. Our results can facilitate the realization of semiconductor-based $0-π$ qubits and Andreev qubits.

cond-mat.mes-hall↗

arXiv2020

Quantum non-demolition dispersive readout of a superconducting artificial atom using large photon numbers

Reading out the state of superconducting artificial atoms typically relies on dispersive coupling to a readout resonator. For a given system noise temperature, increasing the circulating photon number $\bar{n}$ in the resonator enables a shorter measurement time and is therefore expected to reduce readout errors caused by spontaneous atom transitions. However, increasing $\bar{n}$ is generally observed to also increase these transition rates. Here we present a fluxonium artificial atom in which we measure an overall flat dependence of the transition rates between its first two states as a function of $\bar{n}$, up to $\bar{n}\approx200$. Despite the fact that we observe the expected decrease of the dispersive shift with increasing readout power, the signal-to-noise ratio continuously improves with increasing $\bar{n}$. Even without the use of a parametric amplifier, at $\bar{n}=74$, we measure fidelities of 99% and 93% for feedback-assisted ground and excited state preparation, respectively.

quant-ph↗

arXiv2020

Minimizing the discrimination time for quantum states of an artificial atom

Fast discrimination between quantum states of superconducting artificial atoms is an important ingredient for quantum information processing. In circuit quantum electrodynamics, increasing the signal field amplitude in the readout resonator, dispersively coupled to the artificial atom, improves the signal-to-noise ratio and increases the measurement strength. Here we employ this effect over two orders of magnitude in readout power, made possible by the unique combination of a dimer Josephson junction array amplifier with a large dynamic range, and the fact that the readout of our granular aluminum fluxonium artificial atom remained quantum-non-demolition (QND) at relatively large photon numbers in the readout resonator, up to $\overline{n} = 110$. Using Bayesian inference, this allows us to detect quantum jumps faster than the readout resonator response time $2/κ$, where $κ$ is the bandwidth of the readout resonator.

quant-ph↗

arXiv2020

Reducing the impact of radioactivity on quantum circuits in a deep-underground facility

As quantum coherence times of superconducting circuits have increased from nanoseconds to hundreds of microseconds, they are currently one of the leading platforms for quantum information processing. However, coherence needs to further improve by orders of magnitude to reduce the prohibitive hardware overhead of current error correction schemes. Reaching this goal hinges on reducing the density of broken Cooper pairs, so-called quasiparticles. Here, we show that environmental radioactivity is a significant source of nonequilibrium quasiparticles. Moreover, ionizing radiation introduces time-correlated quasiparticle bursts in resonators on the same chip, further complicating quantum error correction. Operating in a deep-underground lead-shielded cryostat decreases the quasiparticle burst rate by a factor fifty and reduces dissipation up to a factor four, showcasing the importance of radiation abatement in future solid-state quantum hardware.

cond-mat.supr-con↗

arXiv2019

State preparation of a fluxonium qubit with feedback from a custom FPGA-based platform

We developed a versatile integrated control and readout instrument for experiments with superconducting quantum bits (qubits), based on a field-programmable gate array (FPGA) platform. Using this platform, we perform measurement-based, closed-loop feedback operations with $428 \, \mathrm{ns}$ platform latency. The feedback capability is instrumental in realizing active reset initialization of the qubit into the ground state in a time much shorter than its energy relaxation time $T_1$. We show experimental results demonstrating reset of a fluxonium qubit with $99.4\,\%$ fidelity, using a readout-and-drive pulse sequence approximately $1.5 \, \mathrm{μs}$ long. Compared to passive ground state initialization through thermalization, with the time constant given by $T_1 = ~ 80 \, \mathrm{μs}$, the use of the FPGA-based platform allows us to improve both the fidelity and the time of the qubit initialization by an order of magnitude.

quant-ph↗

arXiv2019

Phonon traps reduce the quasiparticle density in superconducting circuits

Out of equilibrium quasiparticles (QPs) are one of the main sources of decoherence in superconducting quantum circuits, and are particularly detrimental in devices with high kinetic inductance, such as high impedance resonators, qubits, and detectors. Despite significant progress in the understanding of QP dynamics, pinpointing their origin and decreasing their density remain outstanding tasks. The cyclic process of recombination and generation of QPs implies the exchange of phonons between the superconducting thin film and the underlying substrate. Reducing the number of substrate phonons with frequencies exceeding the spectral gap of the superconductor should result in a reduction of QPs. Indeed, we demonstrate that surrounding high impedance resonators made of granular aluminum (grAl) with lower gapped thin film aluminum islands increases the internal quality factors of the resonators in the single photon regime, suppresses the noise, and reduces the rate of observed QP bursts. The aluminum islands are positioned far enough from the resonators to be electromagnetically decoupled, thus not changing the resonator frequency, nor the loading. We therefore attribute the improvements observed in grAl resonators to phonon trapping at frequencies close to the spectral gap of aluminum, well below the grAl gap.

cond-mat.supr-con↗

arXiv2018

Interplay between kinetic inductance, non-linearity and quasiparticle dynamics in granular aluminum MKIDs

Microwave kinetic inductance detectors (MKIDs) are thin film, cryogenic, superconducting resonators. Incident Cooper pair-breaking radiation increases their kinetic inductance, thereby measurably lowering their resonant frequency. For a given resonant frequency, the highest MKID responsivity is obtained by maximizing the kinetic inductance fraction $α$. However, in circuits with $α$ close to unity, the low supercurrent density reduces the maximum number of readout photons before bifurcation due to self-Kerr non-linearity, therefore setting a bound for the maximum $α$ before the noise equivalent power (NEP) starts to increase. By fabricating granular aluminum MKIDs with different resistivities, we effectively sweep their kinetic inductance from tens to several hundreds of pH per square. We find a NEP minimum in the range of $25\; \text{aW}/\sqrt{\text{Hz}}$ at $α\approx 0.9$, which results from a tradeoff between the onset of non-linearity and a non-monotonic dependence of the noise spectral density vs. resistivity.

cond-mat.supr-con↗

arXiv2018

Granular aluminum: A superconducting material for high impedance quantum circuits

Superconducting quantum information processing machines are predominantly based on microwave circuits with relatively low characteristic impedance, of about 100 Ohm, and small anharmonicity, which can limit their coherence and logic gate fidelity. A promising alternative are circuits based on so-called superinductors, with characteristic impedances exceeding the resistance quantum $R_Q = 6.4$ k$Ω$. However, previous implementations of superinductors, consisting of mesoscopic Josephson junction arrays, can introduce unintended nonlinearity or parasitic resonant modes in the qubit vicinity, degrading its coherence. Here we present a fluxonium qubit design using a granular aluminum (grAl) superinductor strip. Granular aluminum is a particularly attractive material, as it self-assembles into an effective junction array with a remarkably high kinetic inductance, and its fabrication can be in-situ integrated with standard aluminum circuit processing. The measured qubit coherence time $T_2^R$ up to 30 $μ$s illustrates the potential of grAl for applications ranging from protected qubit designs to quantum limited amplifiers and detectors.

cond-mat.supr-con↗

arXiv2018

Concentric transmon qubit featuring fast tunability and an anisotropic magnetic dipole moment

We present a planar qubit design based on a superconducting circuit that we call concentric transmon. While employing a straightforward fabrication process using Al evaporation and lift-off lithography, we observe qubit lifetimes and coherence times in the order of 10us. We systematically characterize loss channels such as incoherent dielectric loss, Purcell decay and radiative losses. The implementation of a gradiometric SQUID loop allows for a fast tuning of the qubit transition frequency and therefore for full tomographic control of the quantum circuit. Due to the large loop size, the presented qubit architecture features a strongly increased magnetic dipole moment as compared to conventional transmon designs. This renders the concentric transmon a promising candidate to establish a site-selective passive direct Z coupling between neighboring qubits, being a pending quest in the field of quantum simulation.

quant-ph↗