arXiv subjects

M. A. Miller

Publications and source records attributed to M. A. Miller.

At least 19 recordsLinked to original sources

arXiv2026

Empirical impact of near-separatrix plasma and neutral transport on the pedestal in the transition between EDA and ELMy H-modes on Alcator C-Mod

The transition between the ELMy H-mode and the EDA H-mode is studied on Alcator C-Mod using an experimental database and predictive pedestal models. High-resolution Thomson scattering measurements are used to compare the pedestal density, $n_{e}^\mathrm{ped}$, and the separatrix density, $n_{e}^\mathrm{sep}$ with main chamber neutral measurements. $n_{e}^\mathrm{ped}$ is sensitive to neutral sources only in the ELMy H-mode regime and not in the EDA H-mode regime. Density fluctuation spectra reveal that quasi-coherent structures become stronger at higher densities and more coherent in the EDA relative to the inter-ELM phases of ELMy H-modes, before weakening again at the highest values of $n_{e}^\mathrm{ped}$. The Saarelma-Connor pedestal density prediction model is validated for ELMy H-modes up to $n_{e}^\mathrm{ped} = 2.0 \times 10^{20}$ m$^{-3}$. An additional transport channel driven by resistive ballooning modes (RBM), $D_\mathrm{RBM}$, scaling directly with $α_{t}$ and inversely with $k_\mathrm{RBM}^{2}\hat{q}_\mathrm{cyl}$ is shown to improve the prediction for EDA H-modes, finding good model agreement up to $n_{e}^\mathrm{ped} = 3.0 \times 10^{20}$ m$^{-3}$. EPED scans in $n_{e}^\mathrm{ped}$ are then performed at three values of $n_{e}^\mathrm{sep}/n_{e}^\mathrm{ped}$. Increasing this ratio moves the peeling-ballooning branch transition to lower $n_{e}^\mathrm{ped}$, increasing $p^\mathrm{ped}$ in the peeling branch and decreasing it in the ballooning branch. Agreement is found for large ELM H-modes. SPARC pedestal density predictions for an ELMy and an EDA/QCE-like H-mode are performed and found consistent with assumptions used in previous EPED modeling. Inclusion of $D_\mathrm{RBM}$ significantly weakens the density gradient near the separatrix, lowering $n_{e}^\mathrm{ped}$ by approximately 20%.

physics.plasm-ph↗

arXiv2026

Experimental Evidence for Increased Particle Fluxes Due to a Change in Transport at the Separatrix near Density Limits on Alcator C-Mod

Experimental inferences of cross-field particle flux at the separatrix, $Γ_{\perp}^\mathrm{sep}$, show rapid growth near H-mode and L-mode density limits at high magnetic field on Alcator C-Mod. Increases in $Γ_{\perp}^\mathrm{sep}$ correlate well with proximity to high density operational boundaries as proposed by the separatrix operational space model. $Γ_{\perp}^\mathrm{sep}$ grows as the L-mode density limit and the H-L-mode back transition boundaries are approached, consistent with expectations of plasma instability-driven turbulence suggested by theory, confirming the power dependence of density limits. $Γ_{\perp}^\mathrm{sep}$ is well-organized by the characteristic wavenumber for resistive ballooning mode turbulence, $k_\mathrm{RBM}$, from interchange-drift-Alfvén fluid turbulence theory, with additional dependence on the cylindrical safety factor, $\hat{q}_\mathrm{cyl}$, yielding an empirical limit to plasma operation of $k_\mathrm{RBM}^{2}\hat{q}_\mathrm{cyl} = 1$. This limit corresponds to the point where the perpendicular heat flux, $Q_{\perp}$, reaches the level of the parallel heat flux, $Q_{\parallel}$, i.e. $Q_{\perp} \approx Q_{\parallel}$, beyond which point thermal equilibrium is not satisfied, resulting in a fold catastrophe.

physics.plasm-ph↗

arXiv2026

A predictive formula for the H-mode electron separatrix density: Bridging regression and physics-based models across C-Mod, AUG and JET tokamaks

The electron density at the separatrix ($n_{e,\mathrm{sep}}$) plays a central role in balancing energy confinement, detachment achievement, and ELM suppression in tokamaks, thereby influencing core-edge integration. To study what determines this key parameter, a database of H-mode separatrix density measurements from Alcator C-Mod, ASDEX Upgrade, and JET tokamaks has been assembled using a consistent analysis method across all devices. This dataset is used to derive a regression scaling expression based solely on engineering parameters, and the results are compared to predictions from the two-point model. The agreement found is remarkable: both the regression and model provide similar parameter dependencies and tokamak-specific multiplicative constants. Building on this agreement, a fully predictive formula that combines the regression dependencies and the two-point model multiplicative constant is proposed. This formula is able to estimate $n_{e,\mathrm{sep}}$ across the three machines within a factor of 1.5, and provides projections to next-step devices (ITER, SPARC, DTT, JT-60SA and COMPASS-U) that are in agreement with available SOLPS simulations.

physics.plasm-ph↗

arXiv2024

Determination of confinement regime boundaries via separatrix parameters on Alcator C-Mod based on a model for interchange-drift-Alfvén turbulence

The separatrix operational space (SepOS) model [Eich \& Manz, \emph{Nuclear Fusion} (2021)] is shown to predict the L-H transition, the L-mode density limit, and the ideal MHD ballooning limit in terms of separatrix parameters for a wide range of Alcator C-Mod plasmas. The model is tested using Thomson scattering measurements across a wide range of operating conditions on C-Mod, spanning $\overline{n}_{e} = 0.3 - 5.5 \times 10^{20}$m$^{-3}$, $B_{t} = 2.5 - 8.0$ T, and $B_{p} = 0.1 - 1.2$ T. An empirical regression for the electron pressure gradient scale length, $λ_{p_{e}}$, against a turbulence control parameter, $α_{t}$, and the poloidal fluid gyroradius, $ρ_{s,p}$, for H-modes is constructed and found to require positive exponents for both regression parameters, indicating turbulence widening of near-SOL widths at high $α_{t}$ and an inverse scaling with $B_{p}$, consistent with results on AUG. The SepOS model is also tested in the unfavorable drift direction and found to apply well to all three boundaries, including the L-H transition as long as a correction to the Reynolds energy transfer term, $α_\mathrm{RS} < 1$ is applied. I-modes typically exist in the unfavorable drift direction for values of $α_{t} \lesssim 0.35$. Finally, an experiment studying the transition between the type-I ELMy and EDA H-mode is analyzed using the same framework. It is found that a recently identified boundary at $α_{t} = 0.55$ excludes most EDA H-modes but that the balance of wavenumbers responsible for the L-mode density limit, namely $k_\mathrm{EM} = k_\mathrm{RBM}$, may better describe the transition on C-Mod. The ensemble of boundaries validated and explored is then applied to project regime access and limit avoidance for the SPARC primary reference discharge parameters.

physics.plasm-ph↗

arXiv2024

Enhanced pedestal transport driven by edge collisionality on Alcator C-Mod and its role in regulating H-mode pedestal gradients

Experimental measurements of plasma and neutral profiles across the pedestal are used in conjunction with 2D edge modeling to examine pedestal stiffness in Alcator C-Mod H-mode plasmas. Experiments on Alcator C-Mod observed pedestal degradation and loss in confinement below a critical value of net power crossing the separatrix, $P_\mathrm{net} = P_\mathrm{net}^\mathrm{crit} \approx 2.3$ MW. New analysis of ionization and particle flux profiles reveal saturation of the pedestal electron density, $n_{e}^\mathrm{ped}$ despite continuous increases in ionization throughout the pedestal, inversely related to $P_\mathrm{net}$. A limit to the pedestal $\nabla n_{e}$ emerges as the particle flux, $Γ_{D}$ continues to grow, implying increases in the effective particle diffusivity, $D_\mathrm{eff}$. This is well-correlated with the separatrix collisionality, $ν^{*}_\mathrm{sep}$ and a turbulence control parameter, $α_{t}$, implying a possible transition in type of turbulence. The transition is well correlated with the experimentally observed value of $P_\mathrm{net}^\mathrm{crit}$. SOLPS-ITER modeling is performed for select discharges from the power scan, constrained with experimental electron and neutral densities, measured at the outer midplane. The modeling confirms general growth in $D_\mathrm{eff}$, consistent with experimental findings, and additionally suggests even larger growth in $χ_{e}$ at the same $P_\mathrm{net}^\mathrm{crit}$.

physics.plasm-ph↗

arXiv2024

Power handling in a highly-radiative negative triangularity pilot plant

This work explores power handling solutions for high-field, highly-radiative negative triangularity (NT) reactors based around the MANTA concept \cite{rutherford_manta_2024}. The divertor design is kept as simple as possible, opting for a standard divertor with standard leg length. FreeGS is used to create an equilibrium for the boundary region, prioritizing a short outer leg length of only $\sim$50 cm ($\sim$40\% of the minor radius). The UEDGE code package is used for the boundary plasma solution, to track plasma temperatures and fluxes to the divertor targets. It is found that for $P_\mathrm{SOL}$ = 25 MW and $n_\mathrm{sep} = 0.96 \times 10^{20}$ m$^{-3}$, conditions consistent with initial core transport modeling, little additional power mitigation is necessary. For external impurity injection of just 0.13\% Ne, the peak heat flux density at the more heavily loaded outer targets falls to 7.8 MW/m$^{2}$, while the electron temperature $T_\mathrm{e}$ remains just under 5 eV. Scans around the parameter space reveal that even at densities lower than in the primary operating scenario, $P_\mathrm{SOL}$ can be increased up to 50 MW, so long as a slightly higher fraction of extrinsic radiator is used. With less than 1\% neon (Ne) impurity content, the divertor still experiences less than 10 MW/m$^{2}$ at the outer target. Design of the plasma-facing components includes a close-fitting vacuum vessel with a tungsten inner surface as well as FLiBe-carrying cooling channels fashioned into the VV wall directly behind the divertor targets. For the seeded heat flux profile, Ansys Fluent heat transfer simulations estimate that the outer target temperature remains at just below 1550\degree C. Initial scoping of advanced divertor designs shows that for an X-divertor, detachment of the outer target becomes much simpler, and plasma fluxes to the targets drop considerably with only 0.01\% Ne content.

physics.plasm-ph↗

arXiv2024

Particle control via cryopumping and its impact on the edge plasma profiles of Alcator C-Mod

At the high $n_{e}$ proposed for high-field fusion reactors, it is uncertain whether ionization, as opposed to plasma transport, will be most influential in determining $n_{e}$ at the pedestal and separatrix. A database of Alcator C-Mod discharges is analyzed to evaluate the impact of source modification via cryopumping. The database contains similarly-shaped H-modes at fixed $I_{p} =$ 0.8 MA and $B_{t} =$ 5.4 T, spanning a large range in $P_\mathrm{net}$ and ionization. Measurements from an edge Thomson Scattering system are combined with those from a midplane-viewing Ly$_α$ camera to evaluate changes to $n_{e}$ and $T_{e}$ in response to changes to ionization rates, $S_\mathrm{ion}$. $n_{e}^\mathrm{sep}$ and $T_{e}^\mathrm{ped}$ are found to be most sensitive to changes to $S_\mathrm{ion}^\mathrm{sep}$, as opposed to $n_{e}^\mathrm{ped}$ and $T_{e}^\mathrm{sep}$. Dimensionless quantities, namely $α_\mathrm{MHD}$ and $ν^{*}$, are found to regulate attainable pedestal values. Select discharges at different values of $P_\mathrm{net}$ and in different pumping configurations are analyzed further using SOLPS-ITER. It is determined that changes to plasma transport coefficients are required to self-consistently model both plasma and neutral edge dynamics. Pumping is found to modify the poloidal distribution of atomic neutral density, $n_{0}$, along the separatrix, increasing $n_{0}$ at the active X-point. Opaqueness to neutrals from high $n_{e}$ in the divertor is found to play a role in mediating neutral penetration lengths and hence, the poloidal distribution of neutrals along the separatrix. Pumped discharges thus require a larger particle diffusion coefficient than that inferred purely from 1D experimental profiles at the outer midplane.

physics.plasm-ph↗

arXiv2024

MANTA: A Negative-Triangularity NASEM-Compliant Fusion Pilot Plant

The MANTA (Modular Adjustable Negative Triangularity ARC-class) design study investigated how negative-triangularity (NT) may be leveraged in a compact, fusion pilot plant (FPP) to take a ``power-handling first" approach. The result is a pulsed, radiative, ELM-free tokamak that satisfies and exceeds the FPP requirements described in the 2021 National Academies of Sciences, Engineering, and Medicine report ``Bringing Fusion to the U.S. Grid". A self-consistent integrated modeling workflow predicts a fusion power of 450 MW and a plasma gain of 11.5 with only 23.5 MW of power to the scrape-off layer (SOL). This low $P_\text{SOL}$ together with impurity seeding and high density at the separatrix results in a peak heat flux of just 2.8 MW/m$^{2}$. MANTA's high aspect ratio provides space for a large central solenoid (CS), resulting in ${\sim}$15 minute inductive pulses. In spite of the high B fields on the CS and the other REBCO-based magnets, the electromagnetic stresses remain below structural and critical current density limits. Iterative optimization of neutron shielding and tritium breeding blanket yield tritium self-sufficiency with a breeding ratio of 1.15, a blanket power multiplication factor of 1.11, toroidal field coil lifetimes of $3100 \pm 400$ MW-yr, and poloidal field coil lifetimes of at least $890 \pm 40$ MW-yr. Following balance of plant modeling, MANTA is projected to generate 90 MW of net electricity at an electricity gain factor of ${\sim}2.4$. Systems-level economic analysis estimates an overnight cost of US\$3.4 billion, meeting the NASEM FPP requirement that this first-of-a-kind be less than US\$5 billion. The toroidal field coil cost and replacement time are the most critical upfront and lifetime cost drivers, respectively.

physics.plasm-ph↗

arXiv2024

Kinetic-Ballooning-Bifurcation in Tokamak Pedestals Across Shaping and Aspect-Ratio

We use a new gyrokinetic threshold model to predict a bifurcation in tokamak pedestal width-height scalings that depends strongly on plasma shaping and aspect-ratio. The bifurcation arises from the first and second stability properties of kinetic-ballooning-modes that yields wide and narrow pedestal branches, expanding the space of accessible pedestal widths and heights. The wide branch offers potential for edge-localized-mode-free pedestals with high core pressure. For negative triangularity, low-aspect-ratio configurations are predicted to give steeper pedestals than conventional-aspect-ratio. Both wide and narrow branches have been attained in tokamak experiments.

physics.plasm-ph↗

arXiv2022

Deep modelling of plasma and neutral fluctuations from gas puff turbulence imaging

The role of turbulence in setting boundary plasma conditions is presently a key uncertainty in projecting to fusion energy reactors. To robustly diagnose edge turbulence, we develop and demonstrate a technique to translate brightness measurements of HeI line radiation into local plasma fluctuations via a novel integrated deep learning framework that combines neutral transport physics and collisional radiative theory for the $3^3 D - 2^3 P$ transition in atomic helium. The tenets for experimental validity are reviewed, illustrating that this turbulence analysis for ionized gases is transferable to both magnetized and unmagnetized environments with arbitrary geometries. Based upon fast camera data on the Alcator C-Mod tokamak, we present the first 2-dimensional time-dependent experimental measurements of the turbulent electron density, electron temperature, and neutral density revealing shadowing effects in a fusion plasma using a single spectral line.

physics.plasm-ph↗

arXiv2021

Experimental Inference of Neutral and Impurity Transport in Alcator C-Mod Using High-Resolution X-Ray and Ultra-Violet Spectra

We present experimental inferences of cross-field impurity transport coefficients for Alcator C-Mod plasmas using a novel forward model for the entire Ca K-alpha spectrum, including satellite lines within the spectral range, to compare to high-resolution X-ray Imaging Crystal Spectroscopy (XICS). These measurements are complemented by Extreme Ultra-Violet (EUV) spectroscopy that constrains transport closer to the edge. Using new atomic data sets for both XICS and EUV analysis has enabled consideration of line ratios across both spectral ranges and has increased the accuracy of inferred transport coefficients. Inclusion of charge exchange between edge thermal neutrals and impurities is shown to be extremely important in C-Mod pedestals. We obtain D atomic neutral densities from experimental D Ly-alpha measurements at the midplane and compare these to SOLPS-ITER simulations, finding good agreement. Bayesian inferences of impurity transport coefficients are presented for L-, EDA H-, and I-mode discharges, making use of the Aurora package for forward modeling and combining our spectroscopic constraints. Experimentally inferred diffusion profiles are found to match turbulent transport models at midradius within uncertainties, using both quasilinear gyro-fluid TGLF SAT-1 and nonlinear ion-scale gyrokinetic CGYRO simulations. Significant discrepancies in convection are observed in some cases, suggesting difficulties in predictions of flat or hollow impurity profiles.

physics.plasm-ph↗

arXiv2020

Encoder-decoder neural network for solving the nonlinear Fokker-Planck-Landau collision operator in XGC

An encoder-decoder neural network has been used to examine the possibility for acceleration of a partial integro-differential equation, the Fokker-Planck-Landau collision operator. This is part of the governing equation in the massively parallel particle-in-cell code, XGC, which is used to study turbulence in fusion energy devices. The neural network emphasizes physics-inspired learning, where it is taught to respect physical conservation constraints of the collision operator by including them in the training loss, along with the L2 loss. In particular, network architectures used for the computer vision task of semantic segmentation have been used for training. A penalization method is used to enforce the "soft" constraints of the system and integrate error in the conservation properties into the loss function. During training, quantities representing the density, momentum, and energy for all species of the system is calculated at each configuration vertex, mirroring the procedure in XGC. This simple training has produced a median relative loss, across configuration space, on the order of 10E-04, which is low enough if the error is of random nature, but not if it is of drift nature in timesteps. The run time for the Picard iterative solver of the operator scales as order n squared, where n is the number of plasma species. As the XGC1 code begins to attack problems including a larger number of species, the collision operator will become expensive computationally, making the neural network solver even more important, since the training only scales as n. A wide enough range of collisionality is considered in the training data to ensure the full domain of collision physics is captured. An advanced technique to decrease the losses further will be discussed, which will be subject of a subsequent report. Eventual work will include expansion of the network to include multiple plasma species.

physics.plasm-ph↗

arXiv2013

Depletion interaction effects on the tunneling conductivity of nanorod suspensions

We study by simulation and theory how the addition of insulating spherical particles affects the conductivity of fluids of conducting rods, modeled by spherocylinders. The electrical connections are implemented as tunneling processes, leading to a more detailed and realistic description than a discontinuous percolation approach. We find that the spheres enhance the tunneling conductivity for a given concentration of rods and that the enhancement increases with rod concentration into the regime where the conducting network is well established. By reformulating the network of rods using a critical path analysis, we quantify the effect of depletion-induced attraction between the rods due to the spheres. Furthermore, we show that our conductivity data are quantitatively reproduced by an effective medium approximation, which explicitly relates the system tunneling conductance to the structure of the rod-sphere fluid.

cond-mat.soft↗

arXiv2013

Measurement of R = sigma_L / sigma_T and the Separated Longitudinal and Transverse Structure Functions in the Nucleon Resonance Region

We report on a detailed study of longitudinal strength in the nucleon resonance region, presenting new results from inclusive electron-proton cross sections measured at Jefferson Lab Hall C in the four-momentum transfer range 0.2 < Q^2 < 5.5 GeV^2. The data have been used to accurately perform 167 Rosenbluth-type longitudinal / transverse separations. The precision R = sigma_L / sigma_T data are presented here, along with the first separate values of the inelastic structure functions F_1 and F_L in this regime. The resonance longitudinal component is found to be significant, both in magnitude and in the existence of defined mass peaks. Additionally, quark-hadron duality is here observed above Q^2 = 1 GeV^2 in the separated structure functions independently.

nucl-ex↗

arXiv2012

Tunneling conductivity in composites of attractive colloids

In conductor-insulator nanocomposites in which conducting fillers are dispersed in an insulating matrix the electrical connectedness is established by interparticle tunneling or hopping processes. These systems are intrinsically non-percolative and a coherent description of the functional dependence of the conductivity $σ$ on the filler properties, and in particular of the conductor-insulator transition, requires going beyond the usual continuum percolation approach by relaxing the constraint of a fixed connectivity distance. In this article we consider dispersions of conducting spherical particles which are connected to all others by tunneling conductances and which are subjected to an effective attractive square well potential. We show that the conductor-insulator transition at low contents $ϕ$ of the conducting fillers does not determine the behavior of $σ$ at larger concentrations, in striking contrast to what is predicted by percolation theory. In particular, we find that at low $ϕ$ the conductivity is governed almost entirely by the stickiness of the attraction, while at larger $ϕ$ values $σ$ depends mainly on the depth of the potential well. As a consequence, by varying the range and depth of the potential while keeping the stickiness fixed, composites with similar conductor-insulator transitions may display conductivity variations of several orders of magnitude at intermediate and large $ϕ$ values. By using a recently developed effective medium theory and the critical path approximation we explain this behavior in terms of dominant tunneling processes which involve interparticle distances spanning different regions of the square-well fluid structure as $ϕ$ is varied. Our predictions could be tested in experiments by changing the potential profile with different depletants in polymer nanocomposites.

cond-mat.dis-nn↗

arXiv2007

The vanishing limit of the square-well fluid: the adhesive hard sphere model as a reference system

We report a simulation study of the gas-liquid critical point for the square-well potential, for values of well width delta as small as 0.005 times the particle diameter sigma. For small delta, the reduced second virial coefficient at the critical point B_2*c is found to depend linearly on delta. The observed weak linear dependence is not sufficient to produce any significant observable effect if the critical temperature T_c is estimated via a constant B_2*c assumption, due to the highly non linear transformation between B_2*c and T_c. This explains the previously observed validity of the law of corresponding states. The critical density rho_c is also found to be constant when measured in units of the cubed average distance between two bonded particles (1+0.5 delta)/sigma. The possibility of describing the delta -> 0 dependence with precise functional forms provides improved acccurate estimates of the critical parameters of the adhesive hard-sphere AHS model.

cond-mat.soft↗

arXiv2004

Phase diagram of the adhesive hard sphere fluid

The phase behavior of the Baxter adhesive hard sphere fluid has been determined using specialized Monte Carlo simulations. We give a detailed account of the techniques used and present data for the fluid-fluid coexistence curve as well as parametrized fits for the supercritical equation of state and the percolation threshold. These properties are compared with the existing results of Percus-Yevick theory for this system.

cond-mat.soft↗

arXiv2000

Evidence for a three-nucleon-force effect in proton-deuteron elastic scattering

Developments in spin-polarized internal targets for storage rings have permitted measurements of 197 MeV polarized protons scattering from vector polarized deuterons. This work presents measurements of the polarization observables A_y, iT_11, and C_y,y in proton-deuteron elastic scattering. When compared to calculations with and without three-nucleon forces, the measurements indicate that three-nucleon forces make a significant contribution to the observables. This work indicates that three-body forces derived from static nuclear properties appear to be crucial to the description of dynamical properties.

nucl-ex↗