arXiv subjects

M. Ciavarella

Publications and source records attributed to M. Ciavarella.

32 records · Page 2Linked to original sources

arXiv2017

A JKR solution for a ball-in-socket contact geometry as a bi-stable adhesive system

In the present note, we start by observing that in the classical JKR theory of adhesion, using the usual Hertzian approximations, the pull-off load grows unbounded when the clearance goes to zero in a conformal "ball in socket" geometry. To consider the case of the conforming geometry, we use a recent rigorous general extension of the original JKR energetic derivation proposed by the first author which necessitates only of adhesionless solutions, and an approximate adhesionless solution given in the literature. We find that depending on a single governing parameter of the problem, theta=DeltaR/(2 pi w R E*) where E* is the plane strain elastic modulus of the material couple, w the surface energy, DeltaR the clearance and R the radius of the sphere, the system shows the classical bistable behaviour for a single sinusoid or a dimpled surface: pull off is approximately that of the JKR theory for theta>0.82 only if the system is not "pushed" strongly enough and otherwise a "strong adhesion" regime is found. Below this value theta<0.82, a strong spontaneous adhesion regime is found similar to "full contact". From the strong regime, pull-off will require a separate investigation depending on the actual system at hand.

cond-mat.soft↗

arXiv2017

An approximate JKR solution for a general contact, including rough contacts

In the present note, we suggest a simple closed form approximate solution to the adhesive contact problem under the so-called JKR regime. The derivation is based on generalizing the original JKR energetic derivation assuming calculation of the strain energy in adhesiveless contact, and unloading at constant contact area. The underlying assumption is that the contact area distributions are the same as under adhesiveless conditions (for an appropriately increased normal load), so that in general the stress intensity factors will not be exactly equal at all contact edges. The solution is simply that the indentation is D=D1-Sqrt(2w A'/P") where w is surface energy, D1 is the adhesiveless indentation, A' is the first derivative of contact area and P" the second derivative of the load with respect to indentation. The solution only requires macroscopic quantities, and not very elaborate local distributions, and is exact in many configurations like axisymmetric contacts. It permits also an estimate of the full solution for elastic rough solids with Gaussian multiple scales of roughness, which so far was lacking, using known adhesiveless simple results. The solution turns out to depend only on rms amplitude and slopes of the surface, and in the fractal limit, slopes would grow without limit, tends to the adhesiveless result - although in this limit the JKR model is inappropriate. However, a more solid result is that the solution would also go to adhesiveless result for large rms amplitude of roughness h_{rms}, irrespective of the small scale details, and in agreement with common sense and previous models by the author.

cond-mat.soft↗

arXiv2016

A random process asperity model for adhesion

A simple asperity model using random process theory is developed in the presence of adhesion. Using the DMT model for each individual asperity, and asymptotic results at large separations, a new adhesion parameter is found, on which the model depends, namely $θ=\frac{w}{E^{\ast}\sqrt{m_{2}/π} m_{0}^{1/2}}$, where $w,E^{\ast},m_{2},m_{0}$ are respectively surface energy, combined elastic modulus, variance of slopes and of heigths of the asperities. This parameter perhaps improves the previous parameter proposed by Fuller and Tabor which assumed identical asperities. the effects of adhesion are found in practice only for θ>0.15. Some implications are discussed and comparisons with recent results are attempted.

cond-mat.mtrl-sci↗

arXiv2016

An upper bound to multiscale roughness-induced adhesion enhancement

Recently Guduru and coworkers have demonstrated with neat theory and experiments that both increase of strength and of toughness are possible in the contact of a rigid sphere with concentric single scale of waviness, against a very soft material. The present note tries to answer the question of a multiscale enhancement of adhesion, considering a Weierstrass series to represent the multiscale roughness, and analytical results only are used. It is concluded that the enhancement is bounded for low fractal dimensions but it can happen, and possibly to very high values, whereas it is even unbounded for high fractal dimensions, but it is also much less likely to occur, because of separated contacts.

cond-mat.mtrl-sci↗

arXiv2016

On the effect of wear on asperity heigth distributions, and the corresponding effect in the mechanical response

Since the time of the original Greenwood & Williamson paper, it was noticed that abrasion and wear lead to possibly bimodal distribution of asperity height distribution, with the upper tail of asperities following from the characteristics of the process. Using a limit case solution due to Borucki for the wear of an originally Gaussian distribution, it is shown here that the tail is indeed always Gaussian, but with different equivalent parameters. Therefore, if the wear process is light, one obtains a bimodal distribution and both may affect the resulting contact mechanics behaviour. In this short note, we illustrate just the main features of the problem. We conclude that it is an oversimplification to consider surfaces Gaussian.

cond-mat.mtrl-sci↗

arXiv2016

On the significance of asperity models predictions of rough contact with respect to recent alternative theories

Recently, it has been shown that while asperity models show correctly qualitative features of rough contact problems (linearity in area-load, negative exponential dependence of load on separation which means also linearity of stiffness with load), the exact value of the coefficients are not precise for the idealized case of Gaussian distribution of heigths. This is due to the intrinsic simplifications, neglecting asperity coalescence and interaction effects. However, the issue of Gaussianity has not been proved or experimentally verified in many cases, and here we show that, for example, assuming a Weibull distribution of asperity heigths, the area-load linear coefficient is not much affected, while the relationships load-separation and therefore also stiffness-load do change largely, particularly when considering bounded distributions of asperity heigths. It is suggested that Gaussianity of surfaces should be further tested in experiments, before applying the most sophisticated rough contact models based on the Gaussian assumption.

cond-mat.mtrl-sci↗

arXiv2016

On roughness-induced adhesion enhancement

While adhesion reduction due to roughness is not surprising, roughness induced adhesion remained a puzzle until recently Guduru and coworkers have shown a very convincing mechanism to explain both the increase of strength and of toughness in a sphere with concentric single scale of waviness. Kesari and coworkers have later shown some very elegant convenient asymptotic expansion of Guduru's solution. This enhancement is very high and indeed, using Kesari's solution, it is here shown to depend uniquely on a Johnson parameter for adhesion of a sinusoidal contact. However, counterintuitively, it leads to unbounded enhancement for conditions of large roughness for which Johnson parameter is very low. Guduru postulated that this enhancement should occur after sufficiently large pressure has been applied to any spherical contact. Also, that although the enhancement is limited to the JKR regime of large soft materials with high adhesion, the DMT limit for the smooth sphere is found otherwise. However, for hard materials, even the DMT limit for the smooth solids is very hard to observe, which suggest that also adhesion reduction is yet not well understood. The limitations of the assumption of simply connected area is here further discussed, and a well known model for hard particles in contact with rough planes due to Rumpf is used to show that in the range where unbounded increase is predicted, orders of magnitude reduction is instead expected for rigid solids. We suggest that Guduru's model may be close to an upper bound to adhesion of rough bodies, while the Rumpf-Rabinovich model may be close to a lower bound.

cond-mat.mtrl-sci↗

arXiv2016

On a recent very simple generalization of DMT theory of adhesion

As the interest in adhesion is shifting towards smaller and smaller scales, the well known Tabor adhesion parameter decreases and the DMT theory is frequently considered to be the appropriate limit. A very attractive much simplified version of DMT has been proposed in a recent investigation of rough contacts by Pastewka & Robbins (PNAS, 111(9), 3298-3303, 2014) which seems to work in very general conditions in numerical experiments. However, when comparing this calculation to the known theories for the sphere, surprisingly large conflicts occur, and the reason for the success of the numerical experiments is obscure.

cond-mat.soft↗

arXiv2016

On Pastewka & Robbins' criterion for macroscopic adhesion of rough surfaces

Pastewka & Robbins (PNAS, 111(9), 3298-3303, 2014) recently have proposed a criterion to distinguish when two surfaces will stick together or not, and suggested it shows a large conflict with asperity theories. It is found that their criterion corresponds very closely to the Fuller and Tabor asperity model one when bandwidth α is small, but otherwise involves a rms ampliture of roughness reduced by a factor Sqrt(α). Therefore, it implies the stickiness of any rough surface is the same as that of the surface where practically all wavelength components of roughness are removed except the very fine ones, which is perhaps counterintuitive. The results are therefore very interesting, if confirmed. Possible sources of approximations are indicated, and a significant error is found in plotting the pull-off data which may improve the fit with Fuller and Tabor. However, still they show finite pull-off values in cases where both their own criterion and an asperity based one seem to suggest non stickiness, and the results are in these respects inconclusive.

cond-mat.soft↗

arXiv2016

A note on the possibility of roughness enhancement of adhesion in Persson's theory

In an attempt to model the observed enhancement of adhesion in some classical experiments in the 1970-1980's, Persson introduced in his theory of adhesion between rough solids a term which corresponds to an area increase due to roughness. In the old experiments, the adhesion enhancement was shown to be up to one order of magnitude, whereas the area increase could not be defined quantitatively because of possibly multiscale roughness. However, in more recent studies by Guduru and collaborators, this enhancement has been further explained with classical Linear Elastic Fracture Mechanics theory, the area enhancement has been shown to be negligible, and therefore the problem of adhesion of rough surfaces remains qualitatively and quantitatively unsolved by Persson's theory.

cond-mat.mtrl-sci↗

arXiv2015

Fracture Mechanics implications for apparent static friction coefficient in contact problems involving slip-weakening laws

We consider the effect of differing coefficients of static and dynamic friction coefficients on the behaviour of contacts involving microslip. The classic solutions of Cattaneo and Mindlin are unchanged if the transition in coefficients is abrupt, but if it occurs over some small slip distance, the solution has some mathematical similarities with those governing the normal tractions in adhesive contact problems. In particular, if the transition to dynamic slip occurs over a sufficiently small area, we can identify a `JKR' approximation, where the transition region is condensed to a line. A local singularity in shear traction is then predicted, with a stress-intensity factor that is proportional to the the square root of the local contact pressure and to a certain integral of the friction coefficient-slip distance relation. We can also define an equivalent of the `small-scale yielding' criterion, which enables us to assess when the singular solution provides a good approximation. One consequence of the results is that the static coefficient of friction determined from force measurements in experiments is significantly smaller than the value that holds at the microscale.

cond-mat.soft↗

arXiv2015

Adhesive rough contacts near complete contact

Recently, there has been some debate over the effect of adhesion on the contact of rough surfaces. Classical asperity theories predict, in agreement with experimental observations, that adhesion is always destroyed by roughness except if the amplitude of the same is extremely small, and the materials are particularly soft. This happens for all fractal dimensions. However, these theories are limited due to the geometrical simplification, which may be particularly strong in conditions near full contact. We introduce therefore a simple model for adhesion, which aims at being rigorous near full contact, where we postulate there are only small isolated gaps between the two bodies. The gaps can be considered as "pressurized cracks" by using Ken Johnson's idea of searching a corrective solution to the full contact solution. The solution is an extension of the adhesive-less solution proposed recently by Xu, Jackson, and Marghitu (XJM model) (2014). This process seems to confirm recent theories using the JKR theory, namely that the effect of adhesion depends critically on the fractal dimension. For D<2.5, the case which includes the vast majority of natural surfaces, there is an expected strong effect of adhesion. Only for large fractal dimensions, D>2.5, seems for large enough magnifications that a full fractal roughness completely destroys adhesion. These results are partly paradoxical since strong adhesion is not observed in nature except in special cases. A possible way out of the paradox may be that the conclusion is relevant for the near full contact regime, where the strong role of flaws at the interfaces, and of gaps full of contaminant, trapped air or liquid in pressure, needs to be further explored. If conditions near full contact are not achieved on loading, probably the conclusions of classical asperity theories may be confirmed.

cond-mat.mtrl-sci↗

arXiv2013

JKR solution for an anisotropic half space

In this paper, the classical JKR theory of the adhesive contact of isotropic elastic spheres is extended to consider the effect of anisotropic elasticity. The contact area will then generally be non-circular, but in many cases it can reasonably be approximated by an ellipse whose dimensions are determined by imposing the energy release rate criterion at the ends of the major and minor axes. Analytical expressions are obtained for the relations between the contact force, the normal displacement and the ellipse semi-axes. It is found that the eccentricity of the contact area decreases during tensile loading and for cases when the point load solution can be accurately described by only one Fourier term, it is almost circular at pull-off, permitting an exact closed form solution for this case. As in the isotropic JKR solution, the pull-off force is independent of the mean elastic modulus, but we find that anisotropy increases the pull-off force and this effect can be quite significant.

cond-mat.mtrl-sci↗

arXiv2013

A critical assessment on Kassapoglou's statistical model for composites fatigue

Kassapoglou recently proposed a model for fatigue of composite materials which seems to suggest that fatigue SN curve can be entirely predicted on the basis of the statistical distribution of static strengths. The original abstract writes "Expressions for the cycles to failure as a function of R ratio are derived. These expressions do not require any curve fitting and do not involve any experimentally determined parameters. The fatigue predictions do not require any fatigue tests for calibration". These surprisingly ambitious claims and attractive results deserve careful scrutiny. We contend that the results seem to be due to a number of approximations and incorrect derivations, and one particular misleading assumption, which make the model not conform to a fatigue testing in a given specimen with resulting SN curve distribution. The quantitative agreement of some predictions (the scatter of distribution of fatigue lives being close to the mode value found in typical composites of aeronautical interest in the large Navy database) should not motivate any enthusiasm. It is believed that a proper statistical treatment of the fatigue process should not make wear-out constants disappear, and hence the SN curves would depend on them, and not just on scatter of static data. These serious concerns explain the large discrepancies found by 3 independent studies which tried to apply Kassapoglou's model to composite fatigue data, and to other well known results.

cond-mat.mtrl-sci↗