arXiv subjects

M. D. Sumption

Publications and source records attributed to M. D. Sumption.

At least 19 recordsLinked to original sources

arXiv2022

White Paper on Leading-Edge technology And Feasibility-directed (LEAF) Program aimed at readiness demonstration for Energy Frontier Circular Colliders by the next decade

In this White Paper for the Snowmass 2021 Process, we propose the establishment of a magnet Leading-Edge technology And Feasibility-directed Program (LEAF Program) to achieve readiness for a future collider decision on the timescale of the next decade. The LEAF Program would rely on, and be synergetic with, generic R&D efforts presently covered - in the US - by the Magnet Development Program (MDP), the Conductor Procurement and R&D (CPRD) Program and other activities in the Office of HEP supported by Early Career Awards (ECA) or Lab Directed R&D (LDRD) funds. Where possible, ties to synergetic efforts in other Offices of DOE or NSF are highlighted and suggested as wider Collaborative efforts on the National scale. International efforts are also mentioned as potential partners in the LEAF Program. We envision the LEAF Program to concentrate on demonstrating the feasibility of magnets for muon colliders as well as next generation high energy hadron colliders, pursuing, where necessary and warranted by the nature of the application, the transition from R&D models to long models/prototypes. The LEAF Program will naturally drive accelerator-quality and experiment-interface design considerations. LEAF will also concentrate, where necessary, on cost reduction and/or industrialization steps.

physics.acc-ph↗

arXiv2014

Enhanced higher temperature (20-30 K) transport properties and irreversibility field in nano-Dy2O3 doped advanced internal Mg infiltration processed MgB2 composites

A series of MgB2 superconducting composite strands co-doped with Dy2O3 and C were prepared via an advanced internal Mg infiltration (AIMI) route.The transport properties and MgB2 layer growth were studied in terms of the Dy2O3 doping level, reaction temperature, and reaction time. Transport studies showed that both critical current densities, Jcs, and irreversibility fields, Birrs, were increased with Dy2O3 doping. The highest layer Jc was 1.35 x 10^5 A/cm2 at 4.2 K, 10 T, 30% higher than that of the best AIMI wires without Dy2O3 doping. The highest "non-barrier" Jc reached 3.6 x 10^4 A/cm2 at 4.2 K, 10 T, which was among the best results reported so far. The improvements were even more pronounced at higher temperatures where the field at which the layer Jc reached 10^4 A/cm2 was pushed out by 0.9 T at 20 K, 1.2 T at 25 K, and 1.4 T at 30 K. While little or no enhancement in Birr was seen at 10 K and 15 K, the increases in Jc at higher temperatures were consistent with observed increases in Birr of 17% at 20 K, 44% at 25 K, and 400% at 30 K. Also, there were some indications that the reaction and layer growth of MgB2 was enhanced by Dy2O3 doping.

cond-mat.supr-con↗

arXiv2012

The critical current density of advanced internal-Mg-diffusion-processed MgB2 wires

Recent advances in MgB2 conductors are leading to a new level of performance. Based on the use of proper powders, proper chemistry, and an architecture which incorporates internal Mg diffusion (IMD), a dense MgB2 structure with not only a high critical current density Jc, but also a high engineering critical current density, Je, can be obtained. In this paper, a series of these advanced (or second - generation, "2G") conductors has been prepared. Scanning electron microscopy and associated energy dispersive X-ray spectroscopy were applied to characterize the microstructures and compositions of the wires, and a dense MgB2 layer structure was observed. The best layer Jc for our sample is 1.07x105 A/cm2 at 10 T, 4.2 K, and our best Je is seen to be 1.67x104 A/cm2 at 10 T, 4.2 K. Optimization of the transport properties of these advanced wires is discussed in terms of B-powder choice, area fraction, and the MgB2 layer growth mechanism.

cond-mat.supr-con↗

arXiv2011

Drawing induced texture and the evolution of superconductive properties with heat treatment time in powder-in-tube in-situ processed MgB2 strands

Monocore powder-in-tube MgB2 strands were cold-drawn and heat-treated at 600C and 700C for times of up to 71 hours and structure-property relationships examined. Drawing-induced elongation of the Mg particles led, after HT, to a textured macrostructure consisting of elongated polycrystalline MgB2 fibers separated by elongated pores. The superconducting Tc, Jc and Fp were correlated with the macrostructure and grain size. Grain size increased with HT time at both 600C and 700C. Jc and hence Fp decreased monotonically but not linearly with grain size. Overall, it was observed that at 700C, the MgB2 reaction was more or less complete after as little as 30 min; at 600C, full reaction completion did not occur until 71 h. into the HT. Transport, Jct(B) was measured in a perpendicular applied field, and the magnetic critical current densities, Jcm\bot(B) and Jcmϕ(B), were measured in perpendicular and parallel (axial) applied fields, respectively. Particularly noticeable was the premature dropoff of Jcm\bot(B) at fields well below the irreversibility field of Jct(B). This effect is attributed to the fibrous macrostructure and its accompanying anisotropic connectivity. Magnetic measurements with the field directed along the strand axis yielded a critical density, Jcm\bot(B), for current flowing transversely to the strand axis that was less than and dropped off more rapidly than Jct(B). In the conventional magnetic measurement, the loop currents that support the magnetization are restricted by the lower of Jct(B) and Jcmϕ (B). In the present case the latter, leading to the premature dropoff of the measured Jcm(B) compared to Jct(B) with increasing field. This result is supported by Kramer plots of the Jcmϕ (B) and Jct(B) data which lead to an irreversibility field for transverse current that is very much less than the usual transport-measured longitudinal one, Birr,t.

cond-mat.supr-con↗

arXiv2011

Influence of Strand Design, Boron Type, and Carbon Doping Method on the Transport Properties of Powder-in-Tube MgB2-XCX Strands

The transport properties of a number of MgB2 strands have been investigated in terms of their response to strand design, starting B powder choice, and the approach to C doping used. The strands had various designs, specifically; (i) several chemical barriers were introduced, viz: Fe and Nb, (ii) the strands were encased in various outer-sheath materials, viz.: monel, Cu+monel, monel+glidcop, Nb+monel, (iii) the filament counts were varied (1, 18, and 36), and (iv) the final strand diameter was varied. In addition, for a subset of the strand designs several B powder and C-dopant types were investigated. Specifically, two types of amorphous B powder were used: (i) Moissan based "Tangshan boron" (ii) "SMI-boron" which is produced in a plasma torch by the reduction-by-hydrogen of BCl3. Two approaches to C doping were taken: (i) "malic-acid treatment" in which C is introduced into the B powder precursor by the moderate temperature drying out a slurry of B mixed in with a malic-acid-toluene solution (during which the malic acid decomposes leaving C as the only solid residue) before the Mg powder is mixed in; (ii) direct C doping of the SMI-produced B by introducing a known percentage of CH4 into the plasma flame. Critical current densities, Jc, were measured on 1.5 m long samples at 4.2 K in fields of up to 14 T; of all the strands measured, that doped with SMI-C at a nominal 4 mol% C (in relation B) yielded the highest Jc values e.g 1.1x105 A/cm2 at 7 T, 4.5x104 at 10 T, and 2.2x104 A/cm2 at 12 T. The n-values are given for all strands at 5 and 10 T, and for a certain set of strands the magnetic field dependencies of the n-values and the influence of C-doping is presented. Finally we demonstrate that, over a wide range of B, log(Jc) decreases linearly with B with a slope -α such that the Jc(B) of any strand can be parameterized in terms of α and its zero-field intercept Jc(B=0).

cond-mat.supr-con↗

arXiv2011

Doping Effect and Flux Pinning Mechanism of Nano-SiC Additions in MgB2 Strands

Superconducting MgB2 strands with nanometer-scale SiC additions have been investigated systematically using transport and magnetic measurements. A comparative study of MgB2 strands with different nano-SiC addition levels has shown C-doping-enhanced critical current density Jc through enhancements in the upper critical field, Hc2, and decreased anisotropy. The critical current density and flux pinning force density obtained from magnetic measurements were found to greatly differ from the values obtained through transport measurements, particularly with regards to magnetic field dependence. The differences in magnetic and transport results are largely attributed to connectivity related effects. On the other hand, based on the scaling behavior of flux pinning force, there may be other effective pinning centers in MgB2 strands in addition to grain boundary pinning.

cond-mat.supr-con↗

arXiv2010

Carbon Doping of MgB2 by Toluene and Malic-Acid-in-Toluene

The decomposition of malic acid in the presence of Mg and B was studied using Differential Scanning Calorimetry (DSC) and Thermogravimetric Analysis (TGA) which revealed that malic acid reacted with Mg but not B. Also, the addition of toluene to dissolve malic acid followed by subsequent drying resulted in no reaction with Mg, indicating that the malic acid had decomposed during the dissolution/drying stage. The total carbon contributed by toluene versus a toluene/5 wt% malic acid mixture was measured using a LECO CS600 carbon analyzer. The toluene sample contained ~0.4 wt% C while the toluene/malic acid mixture had ~1.5 wt% C, demonstrating that the toluene contributed a significant amount of carbon to the final product. Resistivity measurements on powder-in-tube MgB2 monofilamentary wires established that the toluene/malic acid doped sample had the highest Bc2. However, the toluene-only sample had the highest transport Jc over most of the magnetic field range (0-9 T), equaled only by that of toluene/malic acid sample in fields above 9 T.

cond-mat.supr-con↗

arXiv2010

Enhanced superconducting properties of pre-doped B powder type MgB2 strands

Conventional doping methods that directly add C or a C-bearing species to Mg+B powder have the disadvantage of adding C inhomogeneously, yielding either under-reacted regions or blocking phases. Pre-doped B powder provides a more homogeneous distribution of the C dopant in MgB2. Powders containing varying amounts of C were used to produce in-situ MgB2 strands which showed high values of transport Jc (104 A/cm2 at 13.3T). Compared to SiC-added and malic acid-treated strands the pre-doped MgB2 showed both higher values of Birr and transport Jc, indicating that the pre-doping of B leads to more efficient C substitution into the B-sublattice.

cond-mat.supr-con↗

arXiv2010

Thermal Diffusion and Quench Propagation in YBCO Pancake Coils Wound with ZnO-and Mylar Insulations

The thermal diffusion properties of several different kinds of YBCO insulations and the quench properties of pancake coils made using these insulations were studied. Insulations investigated include Nomex, Kapton, and Mylar, as well as insulations based on ZnO, Zn2GeO4, and ZnO-Cu. Initially, short stacks of YBCO conductors with interlayer insulation, epoxy, and a central heater strip were made and later measured for thermal conductivity in liquid nitrogen. Subsequently, three different pancake coils were made. The first two were smaller, each using one meter total of YBCO tape present as four turns around a G-10 former. One of these smaller coils used Mylar insulation co-wound with the YBCO tape, the other used YBCO tape onto which ZnO based insulation had been deposited. One larger coil was made which used 12 total meters of ZnO-insulated tape and had 45 turns. The results for all short sample and coil thermal conductivities were ~1-3 Wm-1K-1. Finally, quench propagation velocity measurements were performed on the coils (77 K, self field) by applying a DC current and then using a heater pulse to initiate a quench. Normal zone propagation velocity (NZP) values were obtained for the coils both in the radial direction and in the azimuthal direction. Radial NZP values (0.05-0.7 mm/s) were two orders of magnitude lower than axial values (~14-17 mm/s). Nevertheless, the quenches were generally seen to propagate radially within the coils, in the sense that any given layer in the coil is driven normal by the layer underneath it.

cond-mat.supr-con↗

arXiv2010

Anisotropic Connectivity and its Influence on Critical Current Densities, Irreversibility Fields, and Flux Creep in In-Situ-Processed MgB2 Strands

The anisotropy of the critical current density (Jc) and its influence on measurement of irreversibility field (Birr) has been investigated for high quality, in-situ MgB2 strands. Comparison of transport and magnetization measurements has revealed the onset of a regime where large differences exist between transport and magnetically measured values of the critical current density and Birr. These effects, initially unexpected due to the lack of crystalline texture in these in-situ processed strands, appear to be due to a fibrous microstructure, connected with the details of the wire fabrication and MgB2 formation reactions. Scanning electron micrographs of in-situ-processed MgB2 monocore strands have revealed a fibrous microstructure. Grains (~100 nm) are randomly oriented, and there is no apparent local texture of the grains. However, this randomly oriented polycrystalline material has a fibrous texture at a larger length scale, with stringers of MgB2 (~ 60 μm long and ~5 μm in diameter) partially separated by elongated pores -- the spaces previously occupied by stringers of elemental Mg. This leads to an interpretation of the differences observed in transport and magnetically determined critical currents, in particular a large deviation between the two at higher fields, in terms of different transverse and longitudinal connectivities within the strand. The different values of connectivity also lead to different resistive transition widths, and thus irreversibility field values, as measured by transport and magnetic techniques. Finally, these considerations are seen to influence estimated pinning potentials for the strands.

cond-mat.supr-con↗

arXiv2008

Prospects for Improving the Intrinsic and Extrinsic Properties of Magnesium Diboride Superconducting Strands

The magnetic and transport properties of magnesium diboride films represent performance goals yet to be attained by powder-processed bulk samples and conductors. Such performance limits are still out of the reach of even the best magnesium diboride magnet wire. In discussing the present status and prospects for improving the performance of powder-based wire we focus attention on (1) the intrinsic (intragrain) superconducting properties of magnesium diboride, Hc2 and flux pinning, (2) factors that control the efficiency with which current is transported from grain-to-grain in the conductor, an extrinsic (intergrain) property. With regard to Item-(1), the role of dopants in Hc2 enhancement is discussed and examples presented. On the other hand their roles in increasing Jc, both via Hc2 enhancement as well as direct fluxoid/pining-center interaction, are discussed and a comprehensive survey of Hc2 dopants and flux-pinning additives is presented. Current transport through the powder-processed wire (an extrinsic property) is partially blocked by the inherent granularity of the material itself and the chemical or other properties of the intergrain surfaces. These and other such results indicate that in many cases less than 15% of the conductor's cross sectional area is able to carry transport current. It is pointed out that densification in association with the elimination of grain-boundary blocking phases would yield five-to ten-fold increases in Jc in relevant regimes, enabling the performance of magnesium diboride in selected applications to compete with that of Nb-Sn.

cond-mat.supr-con↗

arXiv2005

Increases in the Irreversibility Field and the Upper Critical Field of Bulk MgB2 by ZrB2 Addition

In a study of the influence of ZrB2 additions on the irreversibility field, Birr and the upper critical field Bc2, bulk samples with 7.5 at. % ZrB2 additions were made by a powder milling and compaction technique. These samples were then heated to 700-900C for 0.5 hours. Resistive transitions were measured at 4.2 K and Birr and Bc2 values were determined. An increase in Bc2 from 20.5 T to 28.6 T and enhancement of Birr from 16 T to 24 T were observed in the ZrB2 doped sample as compared to the binary sample at 4.2 K. Critical field increases similar to those found with SiC doping were seen at 4.2 K. At higher temperatures, increases in Birr were also determined by M-H loop extrapolation and closure. Values of Birr which were enhanced with ZrB2 doping (as compared to the binary) were seen at temperatures up to 34 K, with Birr values larger than those for SiC doped samples at higher temperatures. The transition temperature, Tc, was then measured using DC susceptibility and a 2.5 K drop of the midpoint of Tc was observed. The critical current density was determined using magnetic measurements and was found to increase at all temperatures between 4.2 K and 35 K with ZrB2 doping.

cond-mat.supr-con↗

arXiv2005

Solenoidal Coils Made from Monofilamentary and Multifilamentary MgB2 strands

Three solenoids have been wound and with MgB2 strand and tested for transport properties. One of the coils was wound with Cu-sheathed monofilamentary strand and the other two with a seven filament strand with Nb-reaction barriers, Cu stabilization, and an outer monel sheath. The wires were first S-glass insulated, then wound onto an OFHC Cu former. The coils were then heat treated at 675C/30 min (monofilamentary strand) and 700C/20 min (multifilamentary strand). Smaller (1 m) segments of representative strand were also wound into barrel-form samples and HT along with the coils. After HT the coils were epoxy impregnated. Transport Jc measurements were performed at various taps along the coil lengths. Measurements were made initially in liquid helium, and then as a function of temperature up to 30 K. Homogeneity of response along the coils was investigated and a comparison to the short sample results was made. Each coil contained more than 100 m of 0.84-1.01 mm OD strand. One of the 7 strand coils reached 222 A at 4.2 K, self field, with a Jc of 300 kA/cm2 in the SC and a winding pack Je of 23 kA/cm2. At 20 K these values were 175 kA/cm2 and 13.4 kA/cm2. Magnet bore fields of 1.5 T and 0.87 T were achieved at 4.2 K and 20 K, respectively. The other multifilamentary coil gave similar results.

cond-mat.supr-con↗

arXiv2004

MgB2/Cu Racetrack Coil: Winding and Transport Testing

A racetrack coil using MgB2/Cu strand has been fabricated and tested for transport current density at 4.2 K in self field. The monofilamentary strand was 1.0 mm OD and insulated with S-glass braid. Eighty turns of strand (42 m) were wound onto a stainless steel former with outer dimensions 25 cm x 10 cm x 0.86 cm. The resulting racetrack coil was heat treated at 675C for 30 minutes in flowing Ar. The strand, with a superconducting fraction of 26%, occupied 49% of the total coil pack cross sectional area. The coil Ic at 4.2 K and self field was 120 A (using a 1 microvolt/cm criterion). This led to a Jc,sc (across the whole coil) of 6.12 x 10^4 A/cm2, a Je in the wire of 1.59 x 10^4 A/cm2, and an overall winding Je of 7.9 x 10^3 A/cm2 at 4.2 K in self field. The n-values ranged from 17 to 56.

cond-mat.supr-con↗

arXiv2004

Large Upper Critical Field and Irreversibility Field in MgB2 wires with SiC additions

Resistive transition measurements are reported for Magnesium diboride strands with SiC dopants. The SiC was added as 10 mol of SiC to 90 mol of binary magnesium diboride. Three different SiC powders were used, the average particle sizes were 200 nm, 30 nm, and 15 nm. The strands were heat treated for times ranging from 5 to 30 minutes at temperatures from 675 to 900. Strands with 200 nm size SiC additions had Hirr and Bc2 which maximized at 25.4 T and 29.7 T after heating at 800C for 30 minutes. The highest values were seen for a strand with 15 nm SiC heated at 725C for 30 minutes which had a Hirr of 29 T and a Bc2 higher than 33 T

cond-mat.supr-con↗

arXiv2004

Irreversibility Field and Flux Pinning in MgB2 with and Without SiC Additions

Critical current density was measured at 4.2 K for MgB2 strands with and without SiC additions. In some cases measurements were performed on longer (1 m) samples wound on barrels, and these were compared to magnetic measurements. Most measurements were performed on short samples at higher fields (up to 18 T). It was found that in-situ processed strands with 10% SiC additions HT at 700-800C show improved Hr and Fp values as compared to control samples, with Hr increasing by 1.5 T. At 900C even larger improvements are seen, with Hr reaching 18 T and Fp values maximizing at 20 GN/m3.

cond-mat.supr-con↗

arXiv2004

AC Loss in Striped (Filamentary) YBCO Coated Conductors Leading to Designs for High Frequencies and Field-Sweep Amplitudes

AC losses of YBCO coated conductors are investigated by calculation and experiment for the higher frequency regime. Previous research using YBCO film deposited onto single crystal substrates demonstrated the effectiveness of filamentary subdivision as a technique for AC loss reduction. As a result of these studies the idea of subdividing YBCO coated conductors (both YBCO, overlayer, and even underlayer) into such stripes suggested itself. The suggestion was implemented by burning grooves into samples of coated conductor using laser micromachining. Various machining parameters were investigated, and the striping and slicing characteristics are presented. Loss measurements were performed on unstriped as well as striped samples by the pick-up coil technique at frequencies of from 50-200 Hz at field sweep amplitudes of up to 150 mT. The effect of soft ferromagnetic Fe shielding was also investigated. The results of the experiments form a starting point for a more general study of reduced loss coated conductor design (including hysteretic, coupling, normal eddy current, and transport losses) projected into higher ranges of frequency and field sweep amplitude with transformer and all cryogenic motor/generator applications in mind.

cond-mat.supr-con↗

arXiv2004

Transport and magnetic Jc of MgB2 strands and small helical coils

The critical current densities of MgB2 monofilamentary strands with and without SiC additions were measured at 4.2 K. Additionally, magnetic Jc at B = 1 T was measured from 4.2 K to 40 K. Various heat treatment times and temperatures were investigated for both short samples and small helical coils. SiC additions were seen to improve high field transport Jc at 4.2 K, but improvements were not evident at 1 T at any temperature. Transport results were relatively insensitive to heat treatment times and temperatures for both short samples and coils in the 700C to 900C range.

cond-mat.supr-con↗