Searcharxiv⌕ Search

arXiv subjects

M. Heller

Publications and source records attributed to M. Heller.

At least 55 records · Page 3Linked to original sources
arXiv2019

SENSE: A comparison of photon detection efficiency and optical crosstalk of various SiPM devices

This paper describes a comparison of photon detection efficiency and optical crosstalk measurements performed by three partners: Geneva University, Catania Observatory and Nagoya University. The measurements were compared for three different SiPM devices with different active areas: from 9 $mm^2$ up to 93.6 $mm^2$ produced by Hamamatsu. The objective of this work is to establish the measurements and analysis procedures for calculating the main SiPM parameters and their precision. This work was done in the scope of SENSE project which aims to build roadmap for the last developments in field of sensors for low light level detection.

physics.ins-det↗
arXiv2017

Control Software for the SST-1M Small-Size Telescope prototype for the Cherenkov Telescope Array

The SST-1M is a 4-m Davies--Cotton atmospheric Cherenkov telescope optimized to provide gamma-ray sensitivity above a few TeV. The SST-1M is proposed as part of the Small-Size Telescope array for the Cherenkov Telescope Array (CTA), the first prototype has already been deployed. The SST-1M control software of all subsystems (active mirror control, drive system, safety system, photo-detection plane, DigiCam, CCD cameras) and the whole telescope itself (master controller) uses the standard software design proposed for all CTA telescopes based on the ALMA Common Software (ACS) developed to control the Atacama Large Millimeter Array (ALMA). Each subsystem is represented by a separate ACS component, which handles the communication to and the operation of the subsystem. Interfacing with the actual hardware is performed via the OPC UA communication protocol, supported either natively by dedicated industrial standard servers (PLCs) or separate service applications developed to wrap lower level protocols (e.g. CAN bus, camera slow control) into OPC UA. Early operations of the telescope without the camera were already carried out. The camera is fully assembled and is capable to perform data acquisition using artificial light source.

astro-ph.IM↗
arXiv2017

Performance of a small size telescope (SST-1M) camera for gamma-ray astronomy with the Cherenkov Telescope Array

The foreseen implementations of the Small Size Telescopes (SST) in CTA will provide unique insights into the highest energy gamma rays offering fundamental means to discover and under- stand the sources populating the Galaxy and our local neighborhood. Aiming at such a goal, the SST-1M is one of the three different implementations that are being prototyped and tested for CTA. SST-1M is a Davies-Cotton single mirror telescope equipped with a unique camera technology based on SiPMs with demonstrated advantages over classical photomultipliers in terms of duty-cycle. In this contribution, we describe the telescope components, the camera, and the trigger and readout system. The results of the commissioning of the camera using a dedicated test setup are then presented. The performances of the camera first prototype in terms of expected trigger rates and trigger efficiencies for different night-sky background conditions are presented, and the camera response is compared to end-to-end simulations.

astro-ph.IM↗
arXiv2017

Development of a strategy for calibrating the novel SiPM camera of the SST-1M telescope proposed for the Cherenkov Telescope Array

CTA will comprise a sub-array of up to 70 small size telescopes (SSTs) at the southern array. The SST-1M project, a 4 m-diameter Davies Cotton telescope with 9 degrees FoV and a 1296 pixels SiPM camera, is designed to meet the requirements of the next generation ground based gamma-ray observatory CTA in the energy range above 3 TeV. Silicon photomultipliers (SiPM) cameras of gamma-ray telescopes can achieve good performance even during high night sky background conditions. Defining a fully automated calibration strategy of SiPM cameras is of great importance for large scale production validation and online calibration. The SST-1M sub-consortium developed a software compatible with CTA pipeline software (CTApipe). The calibration of the SST-1M camera is based on the Camera Test Setup (CTS), a set of LED boards mounted in front of the camera. The CTS LEDs are operated in pulsed or continuous mode to emulate signal and night sky background respectively. Continuous and pulsed light data analysis allows us to extract single pixel calibration parameters to be used during CTA operation.

astro-ph.HE↗
arXiv2016

The ALFA Roman Pot Detectors of ATLAS

The ATLAS Roman Pot system is designed to determine the total proton-proton cross-section as well as the luminosity at the Large Hadron Collider (LHC) by measuring elastic proton scattering at very small angles. The system is made of four Roman Pot stations, located in the LHC tunnel in a distance of about 240~m at both sides of the ATLAS interaction point. Each station is equipped with tracking detectors, inserted in Roman Pots which approach the LHC beams vertically. The tracking detectors consist of multi-layer scintillating fibre structures readout by Multi-Anode-Photo-Multipliers.

physics.ins-det↗
arXiv2016

The Single Mirror Small Sized Telescope For The Cherenkov Telescope Array

The Small Size Telescope with Single Mirror (SST-1M) is one of the proposed types of Small Size Telescopes (SST) for the Cherenkov Telescope Array (CTA). About 70 SST telescopes will be part the CTA southern array which will also include Medium Sized Telescopes (MST) in its threshold configuration. Optimized for the detection of gamma rays in the energy range from 5 TeV to 300 TeV, the SST-1M uses a Davies-Cotton optics with a 4 m dish diameter with a field of view of 9 degrees. The Cherenkov light resulting from the interaction of the gamma-rays in the atmosphere is focused onto a 88 cm side-to-side hexagonal photo-detection plane. The latter is composed of 1296 hollow light guides coupled to large area hexagonal silicon photomultipliers (SiPM). The SiPM readout is fully digital readout as for the trigger system. The compact and lightweight design of the SST-1M camera offers very high performance ideal for gamma-ray observation requirement. In this contribution, the concept, design, performance and status of the first telescope prototype are presented.

astro-ph.IM↗
arXiv2016

Creation of Matter in a Noncommutative Universe

The dark matter and dark energy problem, that is now dominating the research in cosmology, makes the question of the origin of mass-energy content of the universe more urgent than ever. There are two philosophies regarding this question: according to Mach's principle it is matter that generates geometry of space-time, and according to Wheeler's geometrodynamics some configurations of space-time geometry are to be interpreted as its material content. Neither of these philosophies has led to success. In the present paper, we show that there exists an algebraic generalisation of geometry that reconciles, in a sense, these two seemingly opposite standpoints. The geometry is constructed with the help of a noncommutative algebra of smooth functions on a groupoid and its derivations. The groupoid in question has a nice physical interpretation: it can be regarded as a space of Lorentz rotations. In this way, Lorentz symmetries are inherent to the generalised geometry of space-time. We define the action for this geometry and, by varying it, obtain generalised vacuum Einstein equations (for a simplified model). It turns out that these equations contain additional terms (with respect to the standard vacuum Einstein equations) which are naturally interpreted as the components of the energy-momentum tensor. Matter is thus created out of purely geometric degrees of freedom. We find two exact solutions (for even more simplified case). We argue that the creation of matter, being a global effect, makes the contrast between Mach and Wheeler philosophies ineffective.

gr-qc↗
arXiv2015

Prototype of the SST-1M Telescope Structure for the Cherenkov Telescope Array

A single-mirror small-size (SST-1M) Davies-Cotton telescope with a dish diameter of 4 m has been built by a consortium of Polish and Swiss institutions as a prototype for one of the proposed small-size telescopes for the southern observatory of the Cherenkov Telescope Array (CTA). The design represents a very simple, reliable, and cheap solution. The mechanical structure prototype with its drive system is now being tested at the Institute of Nuclear Physics PAS in Krakow. Here we present the design of the prototype and results of the performance tests of the structure and the drive and control system.

astro-ph.IM↗
arXiv2015

Using muon rings for the optical throughput calibration of the SST-1M prototype for the Cherenkov Telescope Array

Imaging Atmospheric Cherenkov Telescopes (IACTs) are ground-based instruments devoted to the study of very high energy gamma-rays coming from space. The detection technique consists of observing images created by the Cherenkov light emitted when gamma rays, or more generally cosmic rays, propagate through the atmosphere. While in the case of protons or gamma-rays the images present a filled and more or less elongated shape, energetic muons penetrating the atmosphere are visualised as characteristic circular rings or arcs. A relatively simple analysis of the ring images allows the reconstruction of all the relevant parameters of the detected muons, such as the energy, the impact parameter, and the incoming direction, with the final aim to use them to calibrate the total optical throughput of the given IACT telescope. We present the results of preliminary studies on the use of images created by muons as optical throughput calibrators of the single mirror small size telescope prototype SST-1M proposed for the Cherenkov Telescope Array.

astro-ph.IM↗
arXiv2015

Software design for the control system for Small-Size Telescopes with single-mirror of the Cherenkov Telescope Array

The Small-Size Telescope with single-mirror (SST-1M) is a 4 m Davies-Cotton telescope and is among the proposed telescope designs for the Cherenkov Telescope Array (CTA). It is conceived to provide the high-energy ($>$ few TeV) coverage. The SST-1M contains proven technology for the telescope structure and innovative electronics and photosensors for the camera. Its design is meant to be simple, low-budget and easy-to-build industrially. Each device subsystem of an SST-1M telescope is made visible to CTA through a dedicated industrial standard server. The software is being developed in collaboration with the CTA Medium-Size Telescopes to ensure compatibility and uniformity of the array control. Early operations of the SST-1M prototype will be performed with a subset of the CTA central array control system based on the Alma Common Software (ACS). The triggered event data are time stamped, formatted and finally transmitted to the CTA data acquisition. The software system developed to control the devices of an SST-1M telescope is described, as well as the interface between the telescope abstraction to the CTA central control and the data acquisition system.

astro-ph.IM↗
arXiv2015

Development of the optical system for the SST-1M telescope of the Cherenkov Telescope Array observatory

The prototype of a Davies-Cotton small size telescope (SST-1M) has been designed and developed by a consortium of Polish and Swiss institutions and proposed for the Cherenkov Telescope Array (CTA) observatory. The main purpose of the optical system is to focus the Cherenkov light emitted by extensive air showers in the atmosphere onto the focal plane detectors. The main component of the system is a dish consisting of 18 hexagonal mirrors with a total effective collection area of 6.47 m2 (including the shadowing and estimated mirror reflectivity). Such a solution was chosen taking into account the analysis of the Cherenkov light propagation and based on optical simulations. The proper curvature and stability of the dish is ensured by the mirror alignment system and the isostatic interface to the telescope structure. Here we present the design of the optical subsystem together with the performance measurements of its components.

astro-ph.IM↗
arXiv2015

Camera calibration strategy of the SST-1M prototype of the Cherenokov Telescope Array

The SST-1M telescope is one of the prototypes under construction proposed to be part of the future Cherenkov Telescope Array. It uses a standard Davis-Cotton design for the optics and telescope structure, with a dish diameter of 4 meters and a large field-of-view of 9 degrees. The innovative camera design is composed of a photo-detection plane with 1296 pixels including entrance window, light concentrators, Silicon Photomultipliers (SiPMs), and pre-amplifier stages together with a fully digital readout and trigger electronics, DigiCam. In this contribution we give a general description of the analysis chain designed for the SST-1M prototype. In particular we focus on the calibration strategy used to convert the SiPM signals registered by DigiCam to the quantities needed for Cherenkov image analysis. The calibration is based on an online feedback system to stabilize the gain of the SiPMs, as well as dedicated events (dark count, pedestal, and light flasher events) to be taken during the normal operation of the prototype.

astro-ph.IM↗
arXiv2015

The SST-1M camera for the Cherenkov Telescope Array

The prototype camera of the single-mirror Small Size Telescopes (SST-1M) proposed for the Cherenkov Telescope Array (CTA) project has been designed to be very compact and to deliver high performance over thirty years of operation. The camera is composed of an hexagonal photo-detection plane made of custom designed large area hexagonal silicon photomultipliers and a high throughput, highly configurable, fully digital readout and trigger system (DigiCam). The camera will be installed on the telescope structure at the H. Niewodnicza{ń}ski institute of Nuclear Physics in Krakow in fall 2015. In this contribution, we review the steps that led to the development of the innovative photo-detection plane and readout electronics, and we describe the test and calibration strategy adopted.

astro-ph.IM↗
arXiv2015

Performance of the SST-1M telescope for the Cherenkov Telescope Array observatory

The single mirror small-size telescope (SST-1M) is one of the telescope projects being proposed for the Cherenkov Telescope Array observatory by a sub-consortium of Polish and Swiss institutions. The SST-1M prototype structure is currently being constructed at the Institute of Nuclear Physics in Cracow, Poland, while the camera will be assembled at the University of Geneva, Switzerland. This prototype enables measurements of parameters having a decisive influence on the telescope performance. We present results of numerical simulations of the SST-1M performance based on such measurements. The telescope effective area, the expected trigger rates and the optical point spread function are calculated.

astro-ph.IM↗
arXiv2015

DigiCam - Fully Digital Compact Read-out and Trigger Electronics for the SST-1M Telescope proposed for the Cherenkov Telescope Array

The SST-1M is one of three prototype small-sized telescope designs proposed for the Cherenkov Telescope Array, and is built by a consortium of Polish and Swiss institutions. The SST-1M will operate with DigiCam - an innovative, compact camera with fully digital read-out and trigger electronics. A high level of integration will be achieved by massively deploying state-of-the-art multi-gigabit transmission channels, beginning from the ADC flash converters, through the internal data and trigger signals transmission over backplanes and cables, to the camera's server link. Such an approach makes it possible to design the camera to fit the size and weight requirements of the SST-1M exactly, and provide low power consumption, high reliability and long lifetime. The structure of the digital electronics will be presented, along with main physical building blocks and the internal architecture of FPGA functional subsystems.

astro-ph.IM↗
arXiv2015

Geometry and General Relativity in the Groupoid Model with a Finite Structure Group

In a series of papers we proposed a model unifying general relativity and quantum mechanics. The idea was to deduce both general relativity and quantum mechanics from a noncommutative algebra ${\cal A}_Γ$ defined on a transformation groupoid $Γ$ determined by the action of the Lorentz group on the frame bundle $(E, π_M, M)$ over space-time $M$. In the present work, we construct a simplified version of the gravitational sector of this model in which the Lorentz group is replaced by a finite group $G$ and the frame bundle is trivial $E=M\times G$. The model is fully computable. We define the Einstein-Hilbert action, with the help of which we derive the generalized vacuum Einstein equations. When the equations are projected to space-time (giving the "general relativistic limit"), the extra terms that appear due to our generalization can be interpreted as "matter terms", as in Kaluza-Klein-type models. To illustrate this effect we further simplify the metric matrix to a block diagonal form, compute for it the generalized Einstein equations and find two of their "Friedmann-like" solutions for the special case when $G =\mathbb{Z}_2$. One of them gives the flat Minkowski space-time (which, however, is not static), another, a hyperbolic, linearly expanding universe.

gr-qc↗
arXiv2014

Generalized derivations and general relativity

We construct differential geometry (connection, curvature, etc.) based on generalized derivations of an algebra ${\cal A}$. Such a derivation, introduced by Bresar in 1991, is given by a linear mapping $u: {\cal A} \rightarrow {\cal A}$ such that there exists a usual derivation $d$ of ${\cal A}$ satisfying the generalized Leibniz rule $u(a b) = u(a) b + a \, d(b)$ for all $a,b \in \cal A$. The generalized geometry "is tested" in the case of the algebra of smooth functions on a manifold. We then apply this machinery to study generalized general relativity. We define the Einstein-Hilbert action and deduce from it Einstein's field equations. We show that for a special class of metrics containing, besides the usual metric components, only one nonzero term, the action reduces to the O'Hanlon action that is the Brans-Dicke action with potential and with the parameter $ω$ equal to zero. We also show that the generalized Einstein equations (with zero energy-stress tensor) are equivalent to those of the Kaluza-Klein theory satisfying a "modified cylinder condition" and having a noncompact extra dimension. This opens a possibility to consider Kaluza-Klein models with a noncompact extra dimension that remains invisible for a macroscopic observer. In our approach, this extra dimension is not an additional physical space-time dimension but appears because of the generalization of the derivation concept.

gr-qc↗