arXiv subjects
Publications and source records attributed to M. Koratzinos.
An updated design for the LEP3 electron-positron collider is presented. The machine is designed to operate in the existing tunnel infrastructure currently hosting the Large Hadron Collider and aims to deliver high luminosity for precision studies of the Z, W, and Higgs boson.
A single-aperture, two-layer Canted-Cosine-Theta (CCT) sextupole magnet using high-temperature superconducting (HTS) ReBCO tape has been developed for the short straight sections (SSS) of FCC through the FCCee-HTS4 project. The magnet was designed, manufactured and tested under cryogenic conditions. Two HTS tapes from two manufacturers have been qualified for this specific application. Design and manufacturing details and cryogenic temperature measurements are presented. This demonstrator represents the first HTS CCT magnet ever constructed.
As stated in the 2019 European Strategy for Particle Physics (ESPP), it is of the utmost importance that the HL-LHC upgrade of the accelerator and the experiments be successfully completed in a timely manner. All necessary efforts should be devoted to achieving this goal. We also recall two of the principal recommendations of the 2019 ESPP for future accelerator initiatives, namely that 1) An electron-positron Higgs factory is the highest priority for the next collider (Rec. c). 2) Europe, together with its international partners, should investigate the technical and financial feasibility of a future hadron collider at CERN with a centre-of-mass energy of at least 100 TeV and with an electron-positron Higgs and electroweak factory as a possible first stage (Rec. e). A major objective in particle physics is always to operate an accelerator that allows a leap of an order of magnitude in the constituent centre-of-mass energy with respect to the previous one. We support FCC-ee and FCC-hh as the preferred option for CERN future, as it addresses both of the above recommendations. The guidance for the 2025 ESPP requests, in addition to the preferred option, the inclusion of ``prioritised alternatives to be pursued if the chosen preferred option turns out not to be feasible or competitive''. Proposed alternatives to the preferred FCC option include linear, muon colliders and LHeC accelerators. In response to this request we propose reusing the existing LHC tunnel for an electron-positron collider, called LEP3, as a back-up alternative if the FCC cannot proceed. LEP3 leverages much of the R\&D conducted for FCC-ee, offers high-precision studies of Z, W, and Higgs bosons below the tt threshold, and offers potential physics performance comparable or superior to other fallback options at a lower cost while supporting continued R\&D towards a next-generation energy frontier machine.
A single aperture Canted-Cosine-Theta (CCT) quadrupole magnet, made of NbTi superconductors, has been developed for the final focus region of the FCC-ee study. The conductor layout is optimised to mitigate edge effects on one of the two sides of the magnet that typically lead to undesired higher-order multipoles. Experimental results of a prototype, including paraffin wax impregnation and cryogenic temperature measurements, are presented. The magnet exhibits no training behaviour, surpassing the nominal current during the initial ramp. Field quality is excellent, with higher-order multipoles below $1\times 10^{-4}$ units, consistent with simulations and room temperature tests. These findings confirm the potential of superconducting CCT magnets to offer compact solutions for applications demanding stringent field quality.
The 2020 update of the European Strategy for Particle Physics emphasised the importance of an intensified and well-coordinated programme of accelerator R&D, supporting the design and delivery of future particle accelerators in a timely, affordable and sustainable way. This report sets out a roadmap for European accelerator R&D for the next five to ten years, covering five topical areas identified in the Strategy update. The R&D objectives include: improvement of the performance and cost-performance of magnet and radio-frequency acceleration systems; investigations of the potential of laser / plasma acceleration and energy-recovery linac techniques; and development of new concepts for muon beams and muon colliders. The goal of the roadmap is to document the collective view of the field on the next steps for the R&D programme, and to provide the evidence base to support subsequent decisions on prioritisation, resourcing and implementation.
The worldwide High Energy Physics community widely agrees that the next collider should be a Higgs factory. Acknowledging this priority, in 2021 CERN has launched the international Future Circular Collider (FCC) Feasibility Study (FS). The FCC Integrated Project foresees, in a first stage, a high-luminosity high-energy electron-positron collider, serving as Higgs, top and electroweak factory, and, in a second stage, an energy frontier hadron collider, with a centre-of-mass energy of at least 100 TeV. In this paper, we address a few key elements of the FCC-ee accelerator design, its performance reach, and underlying technologies, as requested by the Snowmass process. The Conceptual Design Report for the FCC, published in 2019, serves as our primary reference. We also summarize a few recent changes and improvements.
The first FCC-ee final focus quadrupole prototype has been designed, manufactured, assembled and tested at warm. The prototype is a single aperture quadrupole magnet of the CCT type. One edge of the magnet was designed with local multipole cancellation, whereas the other was left with the conventional design. An optimized rotating induction-coil sensor was used. A technique was developed to take into account field distortions due to the environment of the test and distinguish them from magnet effects, demonstrating an excellent field quality for the prototype.
A crucial part of the design of an FCC-ee detector is the minimisation of the disruption of the beam due to the presence of a large and powerful detector magnet. Indeed, the emittance blow-up of the few meters around the interaction point (IP) at lower energies is comparable to the emittance introduced by the rest of the 100 km ring. Vertical emittance is the single most important factor in achieving high performance (luminosity, in this case) in a modern e^+ e^- storage ring such as the FCC-ee. The design adopted is the simplest possible arrangement that can nevertheless deliver high performance: two additional coils per IP side. The performance achieved is such that vertical emittance blow-up will not be a limiting performance factor even in the case of a ring with four experiments, and even in the most demanding energy regime, that of the Z running (about 45 GeV beam energy).
The international Future Circular Collider (FCC) study aims at a design of $pp$, $e^+e^-$, $ep$ colliders to be built in a new 100 km tunnel in the Geneva region. The $e^+e^-$ collider (FCC-ee) has a centre of mass energy range between 90 (Z-pole) and 375 GeV (tt_bar). To reach such unprecedented energies and luminosities, the design of the interaction region is crucial. The crab-waist collision scheme has been chosen for the design and it will be compatible with all beam energies. In this paper we will describe the machine detector interface layout including the solenoid compensation scheme. We will describe how this layout fulfills all the requirements set by the parameters table and by the physical constraints. We will summarize the studies of the impact of the synchrotron radiation, the analysis of trapped modes and of the backgrounds induced by single beam and luminosity effects giving an estimate of the losses in the interaction region and in the detector.
Iron-free CCT magnet design offers many advantages, one being the excellent field quality and the absence of multipole components. However, edge effects are present, although they tend to integrate out over the length of the magnet. Many modern accelerator applications, however, require that these magnets are placed in an area of rapidly varying optics parameters, so magnets with greatly reduced edge effects have an advantage. We have designed such a magnet (a quadrupole) by adding multipole components of the opposite sign to the edge distortions of the magnet. A possible application could be the final focus magnets of the FCC-ee, where beam sizes at the entry and exit point of the magnets vary by large factors. We have then used this technique to effectively eliminate cross talk between adjacent final focus quadrupoles for the incoming and outgoing beams.
A beam optics scheme has been designed for the Future Circular Collider-e+e- (FCC-ee). The main characteristics of the design are: beam energy 45 to 175 GeV, 100 km circumference with two interaction points (IPs) per ring, horizontal crossing angle of 30 mrad at the IP and the crab-waist scheme [1] with local chromaticity correction. The crab-waist scheme is implemented within the local chromaticity correction system without additional sextupoles, by reducing the strength of one of the two sextupoles for vertical chromatic correction at each side of the IP. So-called "tapering" of the magnets is applied, which scales all fields of the magnets according to the local beam energy to compensate for the effect of synchrotron radiation (SR) loss along the ring. An asymmetric layout near the interaction region reduces the critical energy of SR photons on the incoming side of the IP to values below 100 keV, while matching the geometry to the beam line of the FCC proton collider (FCC-hh) [2] as closely as possible. Sufficient transverse/longitudinal dynamic aperture (DA) has been obtained, including major dynamical effects, to assure an adequate beam lifetime in the presence of beamstrahlung and top-up injection. In particular, a momentum acceptance larger than +/-2% has been obtained, which is better than the momentum acceptance of typical collider rings by about a factor of 2. The effects of the detector solenoids including their compensation elements are taken into account as well as synchrotron radiation in all magnets. The optics presented in this paper is a step toward a full conceptual design for the collider. A number of issues have been identified for further study.
The design of the region close to the interaction point of the FCC-ee experiments is especially challenging. The beams collide at an angle (+-15 mrad) in the high-field region of the detector solenoid. Moreover, the very low vertical beta_y* of the machine necessitates that the final focusing quadrupoles have a distance from the IP (L*) of around 2 m and therefore are inside the main detector solenoid. The beams should be screened from the effect of the detector magnetic field, and the emittance blow-up due to vertical dispersion in the interaction region should be minimized, while leaving enough space for detector components. Crosstalk between the two final focus quadrupoles, only about 6 cm apart at the tip, should also be minimized.
The FCC-ee accelerator is considered within the FCC design study as a possible first step towards the ultimate goal of a 100 TeV hadron collider. It is a high luminosity e+e- storage ring collider, designed to cover energies of around 90, 160, 240 and 350GeV ECM (for the Z peak, the WW threshold, the ZH and ttbar cross-section maxima respectively) leading to different operating modes. We report on the current status of the design study, on the most promising concepts and relevant challenges. The expected luminosity performance at all energies, and first studies on transverse polarization for beam energy calibrations will be presented.
The FCC (Future Circular Collider) study represents a vision for the next large project in high energy physics, comprising an 80-100 km tunnel that can house a future 100 TeV hadron collider. The study also includes a high luminosity e+e- collider operating in the centre-of-mass energy range of 90-350 GeV as a possible intermediate step, the FCC-ee. The FCC-ee aims at definitive electro-weak precision measurements of the Z, W, H and top particles, and search for rare phenomena. Although FCC-ee is based on known technology, the goal performance in luminosity and energy calibration make it quite challenging. During 2014 the study went through an exploration phase. The study has now entered its second year and the aim is to produce a conceptual design report during the next three to four years. We here report on progress since the last IPAC conference.
Renewed interest in circular e+e- colliders has spurred designs of single beam-pipe machines, like the CEPC in China, and double beam pipe ones, such as the FCC-ee effort at CERN. Single beam-pipe designs profit from lower costs but are limited by the number of bunches that can be accommodated in the machine. We analyse these performance limitations and propose a solution that can accommodate O(1000) bunches while keeping more than 90% of the ring with a single beam pipe.
The FCC-ee aims to improve on electroweak precision measurements, with goals of 100 keV on the Z mass and width, and a fraction of MeV on the W mass. Compared to LEP, this implies a much improved knowledge of the centre-of-mass energy when operating at the Z peak and WW threshold. This can be achieved by making systematic use of resonant depolarization. A number of issues have been identified, due in particular to the long polarization times. However the smaller emittance and energy spread of FCC-ee with respect to LEP should help achieve a much improved performance.
In this paper I will commend on the early CEPC design as of October 2014. In particular I will comment on the choice of circumference, minimum and maximum energy, number of collision points and target luminosity. I will finish with suggestions to increase performance with minimum incremental cost.
In this paper we deal with aspects of transverse polarization for the purpose of energy calibration of proposed circular colliders like the FCC-ee and the CEPC. The main issues of such a measurement will be discussed. The possibility of using this method to accurately determine the energy at the WW threshold as well as the Z peak will be addressed. The use of wigglers for reducing long polarization times will be discussed and a possible strategy will be presented for minimising the energy uncertainty error in these large machines.