Searcharxiv⌕ Search

arXiv subjects

M. Povoli

Publications and source records attributed to M. Povoli.

8 recordsLinked to original sources
arXiv2024

LURAD: Design Study of a Comprehensive Radiation Monitor Package for the Gateway and the Lunar Surface

Moon is an auspicious environment for the study of Galactic cosmic rays (GCR) and Solar particle events (SEP) due to the absence of magnetic field and atmosphere. The same characteristics raise the radiation risk for human presence in orbit around it or at the lunar surface. The secondary (albedo) radiation resulting from the interaction of the primary radiation with the lunar soil adds an extra risk factor, because neutrons are produced, but also it can be exploited to study the soil composition. In this paper, the design of a comprehensive radiation monitor package tailored to the lunar environment is presented. The detector, named LURAD, will perform spectroscopic measurements of protons, electrons, heavy ions, as well as gamma-rays, and neutrons. A microdosimetry monitor subsystem is foreseen which can provide measurements of LET(Si) spectra in a wide dynamic range of LET(Si) and flux for SPE and GCR, detection of neutrons and biological dose for radiation protection of astronauts. The LURAD design leverages on the following key enabling technologies: (a) Fully depleted Si monolithic active pixel sensors; (b) Scintillators read by silicon photomultipliers (SiPM); (c) Silicon on Insulator (SOI) microdosimetry sensors; These technologies promise miniaturization and mass reduction with state-of-the-art performance. The instrument's design is presented, and the Monte Carlo study of the feasibility of particle identification and kinetic energy determination is discussed

astro-ph.IM↗
arXiv2014

Testbeam and Laboratory Characterization of CMS 3D Pixel Sensors

The pixel detector is the innermost tracking device in CMS, reconstructing interaction vertices and charged particle trajectories. The sensors located in the innermost layers of the pixel detector must be upgraded for the ten-fold increase in luminosity expected with the High- Luminosity LHC (HL-LHC) phase. As a possible replacement for planar sensors, 3D silicon technology is under consideration due to its good performance after high radiation fluence. In this paper, we report on pre- and post- irradiation measurements for CMS 3D pixel sensors with different electrode configurations. The effects of irradiation on electrical properties, charge collection efficiency, and position resolution of 3D sensors are discussed. Measurements of various test structures for monitoring the fabrication process and studying the bulk and surface properties, such as MOS capacitors, planar and gate-controlled diodes are also presented.

physics.ins-det↗
arXiv2012

Characterization of proton irradiated 3D-DDTC pixel sensor prototypes fabricated at FBK

In this paper we discuss results relevant to 3D Double-Side Double Type Column (3D-DDTC) pixel sensors fabricated at FBK (Trento, Italy) and oriented to the ATLAS upgrade. Some assemblies of these sensors featuring different columnar electrode configurations (2, 3, or 4 columns per pixel) and coupled to the ATLAS FEI3 read-out chip were irradiated up to large proton fluences and tested in laboratory with radioactive sources. In spite of the non optimized columnar electrode overlap, sensors exhibit reasonably good charge collection properties up to an irradiation fluence of 2 x 10**15 neq/cm2, while requiring bias voltages in the order of 100 V. Sensor operation is further investigated by means of TCAD simulations which can effectively explain the basic mechanisms responsible for charge loss after irradiation.

physics.ins-det↗
arXiv2011

Test Beam Results of 3D Silicon Pixel Sensors for the ATLAS upgrade

Results on beam tests of 3D silicon pixel sensors aimed at the ATLAS Insertable-B-Layer and High Luminosity LHC (HL-LHC)) upgrades are presented. Measurements include charge collection, tracking efficiency and charge sharing between pixel cells, as a function of track incident angle, and were performed with and without a 1.6 T magnetic field oriented as the ATLAS Inner Detector solenoid field. Sensors were bump bonded to the front-end chip currently used in the ATLAS pixel detector. Full 3D sensors, with electrodes penetrating through the entire wafer thickness and active edge, and double-sided 3D sensors with partially overlapping bias and read-out electrodes were tested and showed comparable performance.

physics.ins-det↗
arXiv2009

Characterization of 3D-DDTC detectors on p-type substrates

We report on the electrical and functional characterization of 3D Double-side, Double-Type-Column (3D- DDTC) detectors fabricated on p-type substrates. Results relevant to detectors in the diode, strip and pixel configurations are presented, and demonstrate a clear improvement in the charge collection performance compared to the first prototypes of these detectors.

physics.ins-det↗
arXiv2009

Preliminary results of 3D-DDTC pixel detectors for the ATLAS upgrade

3D Silicon sensors fabricated at FBK-irst with the Double-side Double Type Column (DDTC) approach and columnar electrodes only partially etched through p-type substrates were tested in laboratory and in a 1.35 Tesla magnetic field with a 180GeV pion beam at CERN SPS. The substrate thickness of the sensors is about 200um, and different column depths are available, with overlaps between junction columns (etched from the front side) and ohmic columns (etched from the back side) in the range from 110um to 150um. The devices under test were bump bonded to the ATLAS Pixel readout chip (FEI3) at SELEX SI (Rome, Italy). We report leakage current and noise measurements, results of functional tests with Am241 gamma-ray sources, charge collection tests with Sr90 beta-source and an overview of preliminary results from the CERN beam test.

physics.ins-det↗
arXiv2009

Development of 3D-DDTC pixel detectors for the ATLAS upgrade

We report on the development of n-on-p, 3D Double-Side Double Type Column (3D-DDTC) pixel detectors fabricated at FBK-irst (Trento, Italy) and oriented to the ATLAS upgrade. The considered fabrication technology is simpler than that required for full 3D detectors with active edge, but the detector efficiency and radiation hardness critically depend on the columnar electrode overlap and should be carefully evaluated. The first assemblies of these sensors (featuring 2, 3, or 4 columns per pixel) with the ATLAS FEI3 read-out chip have been tested in laboratory. Selected results from the electrical and functional characterization with radioactive sources are here discussed.

physics.ins-det↗