SearcharxivSearch

arXiv subjects

M. Rameez

Publications and source records attributed to M. Rameez.

At least 19 recordsLinked to original sources

The muon charge asymmetry and the directional distribution of thunderstorm events observed by the GRAPES-3 muon telescope

The electric fields inside thunderstorms can significantly modify the intensity of secondary cosmic ray muons at the ground level, producing measurable variations in their intensity ($\Delta$I$_{\mu}$). By utilizing the decade-long observations of thunderstorms (April 2011-December 2020) by the GRAPES-3 muon telescope (G3MT), a directional asymmetry in $\Delta$I$_{\mu}$ is observed, with nearly six times more events being detected from the east than the west directions. Using detailed CORSIKA Monte Carlo simulations, it is shown that this asymmetry is caused by the variations of the muon charge ratio R$_\mu$ (N$_{\mu^+}$/N$_{\mu^-}$). The anisotropic R$_\mu$ in turn, is caused by the systematic changes in geomagnetic cutoff rigidities, and subsequent selective filtering of predominantly positively charged primary cosmic rays. As a consequence, the R$_\mu$ increases systematically from west to east across the G3MT field of view, enhancing the sensitivity of east directions to positively charged thunderstorm top. Monte Carlo simulations with constant R$_\mu$ show that the directional asymmetry disappears, demonstrating the muon charge imbalance to be the dominant driver of the observed asymmetry. The dependence of R$_\mu$ on the hadronic interaction is also studied by comparing seven combinations high-, and low-energy hadronic interaction generators, which show a $\lesssim$7% spread in R$_\mu$, and $\lesssim$14% variation in the derived thunderstorm potentials. These results provide the first quantitative link between the muon charge asymmetry caused by the geomagnetic field, and the directional distribution of thunderstorms, reinforcing the role of muon observations as a probe of gigavolt potentials in atmospheric electrical structures.

astro-ph.HE

Monitoring the upper atmospheric temperature and interplanetary magnetic field with the GRAPES-3 muon telescope

We study the influence of variations in the upper atmospheric temperature and interplanetary magnetic field on the cosmic ray induced atmospheric muon flux measured by the GRAPES-3 experiment over 22 years (2001--2022) of data; spanning three solar cycles: the declining phase of Solar Cycle 23, the full Cycle 24, and the rising and maximum phases of Cycle 25. Located in Ooty- India, the GRAPES-3 large area (560\,$m^2$) muon telescope detects $\sim$4 billion muons daily above 1\,GeV, with an angular resolution of $\sim$4$^\circ$, enabling a statistical precision $<$0.01\% on the hourly muon rate. After accounting for the effect of atmospheric pressure variations, we compare this data with the upper atmospheric temperature inferred from NASA's MERRA-2 dataset as well as magnetic field data from the ACE and WIND spacecraft at Lagrange point L1. A simultaneous iterative fitting method employing Fast Fourier Transforms and a narrow band-pass filter reveals the temperature and magnetic field coefficients to be $\alpha_T=-\,0.2241\,\pm\,0.04\, (stat.)\,\pm\,0.0220\, (syst.)\,\%\,K^{-1}$ and $\gamma_{M}=-\,0.574\,\pm\,0.027\, (stat.)\,\pm\,0.011\, (syst.)\,\%\,\text{nT}^{-1}$, respectively, for an assumed hadronic attenuation length $\lambda$=120 g cm$^{-2}$, underscoring the potential of the GRAPES-3 muon telescope to serve as a real time monitor of the upper atmospheric temperature or interplanetary magnetic field.

astro-ph.HE

An automated algorithmic method to mitigate long-term variations in the efficiency of the GRAPES-3 muon telescope

The GRAPES-3 large area muon telescope with its sixteen independent modules records the high energy (>1 GeV) muons continuously over 2.3 sr of the sky. However, the recorded muon rates are contaminated by instrumental effects and instabilities spanning both short- and long-timescales, such as variations in the efficiency of the detector. We present an automated, algorithmic method, which employs Bayesian blocks to discretize the data stream into periods and exploits the correlations among the sixteen independent modules of the muon telescope to separate the impact of these instrumental problems from those originating in physical effects of interest, allowing the Savitzky-Golay filter to be employed to mitigate the former. Compared to legacy methods, this method is less dependent on subjective input from experimental operators and provides a data stream free of all known instrumental effects over calendar years. The muon rate obtained with the new method shows a fairly better correlation with neutron monitor data, than that obtained with the legacy method.

astro-ph.IM

Dependence of the estimated electric potential in thunderstorms observed at GRAPES-3 on the hadronic interaction generators used in simulations

A potential difference of 1.3 Giga-Volts (GV) was inferred across a thundercloud using data from the GRAPES-3 muon telescope (G3MT) [1]. This was the first-ever estimation of gigavolt potential in thunderstorms, confirming prediction of C.T.R. Wilson almost a century ago. To infer the thundercloud potential required acceleration of muons in atmospheric electric field to be incorporated in the Monte Carlo simulation software CORSIKA. The G3MT records over 4 billion muons daily that are grouped into 169 directions covering 2.3 sr sky. This enabled changes as small as 0.1% in the muon flux on minute timescale, caused by thunderstorms to be accurately measured. But that requires high statistics simulation of muon fluxes in thunderstorm electric fields. The CORSIKA offers a choice of several generators for low- (FLUKA, GHEISHA, and UrQMD) and high-energy (SIBYLL, EPOS-LHC, and QGSJETII) hadronic interactions. Since it is unclear which combination of the low- and high-energy generators provides the correct description of hadronic interactions, all nine combinations of generators were explored, and they yielded thundercloud potentials ranging from 1.3 GV to 1.6 GV for the event recorded on 1 December 2014. The result of SIBYLL-FLUKA combination yielded the lowest electric potential of 1.3 GV was reported. Furthermore, another seven major thunderstorm events recorded between April 2011 and December 2020 were analyzed to measure the dependence of their thundercloud potential on the hadronic interaction generators. It is observed that the low-energy generators produce larger variation ($\sim$14%) in thundercloud potential than the high-energy generators ($\sim$8%). This probably reflects the fact that the GeV muons are predominantly produced in low-energy ($<$80 GeV) interactions, which effectively magnifies the differences in the meson production cross-sections among the low-energy generators.

astro-ph.HE

Small-scale cosmic ray anisotropy observed by the GRAPES-3 experiment at TeV energies

GRAPES-3 is a mid-altitude (2200 m) and near equatorial ($11.4^{\circ}$ North) air shower array, overlapping in its field of view for cosmic ray observations with experiments that are located in Northern and Southern hemispheres. We analyze a sample of $3.7\times10^9$ cosmic ray events collected by the GRAPES-3 experiment between 1 January 2013 and 31 December 2016 with a median energy of $\sim16$ TeV for study of small-scale ($<60^{\circ}$) angular scale anisotropies. We observed two structures labeled as A and B, deviate from the expected isotropic distribution of cosmic rays in a statistically significant manner. Structure `A' spans $50^{\circ}$ to $80^{\circ}$ in the right ascension and $-15^{\circ}$ to $30^{\circ}$ in the declination coordinate. The relative excess observed in the structure A is at the level of $(6.5\pm1.3)\times10^{-4}$ with a statistical significance of 6.8 standard deviations. Structure `B' is observed in the right ascension range of $110^{\circ}$ to $140^{\circ}$. The relative excess observed in this region is at the level of $(4.9\pm1.4)\times10^{-4}$ with a statistical significance of 4.7 standard deviations. These structures are consistent with those reported by Milagro, ARGO-YBJ, and HAWC. These observations could provide a better understanding of the cosmic ray sources, propagation and the magnetic structures in our Galaxy.

astro-ph.HE

The dipole anisotropy of AllWISE galaxies

We determine the dipole in the WISE galaxy catalogue. After reducing star contamination to <0.1% by rejecting sources with high apparent motion and those close to the Galactic plane, we eliminate low redshift sources to suppress the non-kinematic, clustering dipole. We remove sources within {\pm}5° of the super-galactic plane, as well as those within 1'' of 2MRS sources at redshift z < 0.03. We enforce cuts on the source angular extent to preferentially select distant ones. As we progress along these steps, the dipole converges in direction to within 5° of the CMB dipole and its magnitude also progressively reduces but stabilises at {\sim}0.012, corresponding to a velocity >1000 km/s if it is solely of kinematic origin. However, previous studies have shown that only {\sim}70% of the velocity of the Local Group as inferred from the CMB dipole is due to sources at z < 0.03. We examine the Dark Sky simulations to quantify the prevalence of such environments and find that <2.1% of Milky Way-like observers in a ΛCDM universe should observe the bulk flow (> 240 km/s extending to z > 0.03) that we do. We construct mock catalogues in the neighbourhood of such peculiar observers in order to mimic our final galaxy selection and quantify the residual clustering dipole. After subtracting this the remaining dipole is 0.0048 {\pm} 0.0022, corresponding to a velocity of 420 {\pm} 213 km/s which is consistent with the CMB. However the sources (at z > 0.03) of such a large clustering dipole remain to be identified.

astro-ph.CO

High redshift radio galaxies and divergence from the CMB dipole

Previous studies have found our velocity in the rest frame of radio galaxies at high redshift to be substantially larger than that inferred from the CMB temperature dipole anisotropy. We construct a full sky catalogue NVSUMSS, by merging the NVSS and SUMSS catalogues and removing local sources by various means including cross-correlating with the 2MRS catalogue. We take into account both aberration and Doppler boost to deduce our velocity from the hemispherical number count asymmetry, as well as via a 3-dimensional linear estimator. Both the magnitude and direction depend on cuts made to the catalogue, e.g. on the lowest source flux, however these effects are small. With the hemispheric number count asymmetry method we obtain a velocity of 1729 $\pm$ 187 km/s i.e. about 4 times larger than that obtained from the CMB dipole, but close in direction, towards RA=149 $\pm$ 2 degree, DEC = -17 $\pm$ 12 degree. With the 3-dimensional estimator, the derived velocity is 1355 $\pm$ 174 km/s towards RA=141 $\pm$ 11 degree, DEC=-9 $\pm$ 10 degree. We assess the statistical significance of these results by constructing catalogues of random distributions and show that they are at best significant at the $2.81 σ$ (99.95% confidence) level.

astro-ph.CO

The Single Mirror Small Sized Telescope For The Cherenkov Telescope Array

The Small Size Telescope with Single Mirror (SST-1M) is one of the proposed types of Small Size Telescopes (SST) for the Cherenkov Telescope Array (CTA). About 70 SST telescopes will be part the CTA southern array which will also include Medium Sized Telescopes (MST) in its threshold configuration. Optimized for the detection of gamma rays in the energy range from 5 TeV to 300 TeV, the SST-1M uses a Davies-Cotton optics with a 4 m dish diameter with a field of view of 9 degrees. The Cherenkov light resulting from the interaction of the gamma-rays in the atmosphere is focused onto a 88 cm side-to-side hexagonal photo-detection plane. The latter is composed of 1296 hollow light guides coupled to large area hexagonal silicon photomultipliers (SiPM). The SiPM readout is fully digital readout as for the trigger system. The compact and lightweight design of the SST-1M camera offers very high performance ideal for gamma-ray observation requirement. In this contribution, the concept, design, performance and status of the first telescope prototype are presented.

astro-ph.IM

Prototype of the SST-1M Telescope Structure for the Cherenkov Telescope Array

A single-mirror small-size (SST-1M) Davies-Cotton telescope with a dish diameter of 4 m has been built by a consortium of Polish and Swiss institutions as a prototype for one of the proposed small-size telescopes for the southern observatory of the Cherenkov Telescope Array (CTA). The design represents a very simple, reliable, and cheap solution. The mechanical structure prototype with its drive system is now being tested at the Institute of Nuclear Physics PAS in Krakow. Here we present the design of the prototype and results of the performance tests of the structure and the drive and control system.

astro-ph.IM

Using muon rings for the optical throughput calibration of the SST-1M prototype for the Cherenkov Telescope Array

Imaging Atmospheric Cherenkov Telescopes (IACTs) are ground-based instruments devoted to the study of very high energy gamma-rays coming from space. The detection technique consists of observing images created by the Cherenkov light emitted when gamma rays, or more generally cosmic rays, propagate through the atmosphere. While in the case of protons or gamma-rays the images present a filled and more or less elongated shape, energetic muons penetrating the atmosphere are visualised as characteristic circular rings or arcs. A relatively simple analysis of the ring images allows the reconstruction of all the relevant parameters of the detected muons, such as the energy, the impact parameter, and the incoming direction, with the final aim to use them to calibrate the total optical throughput of the given IACT telescope. We present the results of preliminary studies on the use of images created by muons as optical throughput calibrators of the single mirror small size telescope prototype SST-1M proposed for the Cherenkov Telescope Array.

astro-ph.IM

Software design for the control system for Small-Size Telescopes with single-mirror of the Cherenkov Telescope Array

The Small-Size Telescope with single-mirror (SST-1M) is a 4 m Davies-Cotton telescope and is among the proposed telescope designs for the Cherenkov Telescope Array (CTA). It is conceived to provide the high-energy ($>$ few TeV) coverage. The SST-1M contains proven technology for the telescope structure and innovative electronics and photosensors for the camera. Its design is meant to be simple, low-budget and easy-to-build industrially. Each device subsystem of an SST-1M telescope is made visible to CTA through a dedicated industrial standard server. The software is being developed in collaboration with the CTA Medium-Size Telescopes to ensure compatibility and uniformity of the array control. Early operations of the SST-1M prototype will be performed with a subset of the CTA central array control system based on the Alma Common Software (ACS). The triggered event data are time stamped, formatted and finally transmitted to the CTA data acquisition. The software system developed to control the devices of an SST-1M telescope is described, as well as the interface between the telescope abstraction to the CTA central control and the data acquisition system.

astro-ph.IM

Development of the optical system for the SST-1M telescope of the Cherenkov Telescope Array observatory

The prototype of a Davies-Cotton small size telescope (SST-1M) has been designed and developed by a consortium of Polish and Swiss institutions and proposed for the Cherenkov Telescope Array (CTA) observatory. The main purpose of the optical system is to focus the Cherenkov light emitted by extensive air showers in the atmosphere onto the focal plane detectors. The main component of the system is a dish consisting of 18 hexagonal mirrors with a total effective collection area of 6.47 m2 (including the shadowing and estimated mirror reflectivity). Such a solution was chosen taking into account the analysis of the Cherenkov light propagation and based on optical simulations. The proper curvature and stability of the dish is ensured by the mirror alignment system and the isostatic interface to the telescope structure. Here we present the design of the optical subsystem together with the performance measurements of its components.

astro-ph.IM

Camera calibration strategy of the SST-1M prototype of the Cherenokov Telescope Array

The SST-1M telescope is one of the prototypes under construction proposed to be part of the future Cherenkov Telescope Array. It uses a standard Davis-Cotton design for the optics and telescope structure, with a dish diameter of 4 meters and a large field-of-view of 9 degrees. The innovative camera design is composed of a photo-detection plane with 1296 pixels including entrance window, light concentrators, Silicon Photomultipliers (SiPMs), and pre-amplifier stages together with a fully digital readout and trigger electronics, DigiCam. In this contribution we give a general description of the analysis chain designed for the SST-1M prototype. In particular we focus on the calibration strategy used to convert the SiPM signals registered by DigiCam to the quantities needed for Cherenkov image analysis. The calibration is based on an online feedback system to stabilize the gain of the SiPMs, as well as dedicated events (dark count, pedestal, and light flasher events) to be taken during the normal operation of the prototype.

astro-ph.IM

The SST-1M camera for the Cherenkov Telescope Array

The prototype camera of the single-mirror Small Size Telescopes (SST-1M) proposed for the Cherenkov Telescope Array (CTA) project has been designed to be very compact and to deliver high performance over thirty years of operation. The camera is composed of an hexagonal photo-detection plane made of custom designed large area hexagonal silicon photomultipliers and a high throughput, highly configurable, fully digital readout and trigger system (DigiCam). The camera will be installed on the telescope structure at the H. Niewodnicza{ń}ski institute of Nuclear Physics in Krakow in fall 2015. In this contribution, we review the steps that led to the development of the innovative photo-detection plane and readout electronics, and we describe the test and calibration strategy adopted.

astro-ph.IM

Performance of the SST-1M telescope for the Cherenkov Telescope Array observatory

The single mirror small-size telescope (SST-1M) is one of the telescope projects being proposed for the Cherenkov Telescope Array observatory by a sub-consortium of Polish and Swiss institutions. The SST-1M prototype structure is currently being constructed at the Institute of Nuclear Physics in Cracow, Poland, while the camera will be assembled at the University of Geneva, Switzerland. This prototype enables measurements of parameters having a decisive influence on the telescope performance. We present results of numerical simulations of the SST-1M performance based on such measurements. The telescope effective area, the expected trigger rates and the optical point spread function are calculated.

astro-ph.IM

DigiCam - Fully Digital Compact Read-out and Trigger Electronics for the SST-1M Telescope proposed for the Cherenkov Telescope Array

The SST-1M is one of three prototype small-sized telescope designs proposed for the Cherenkov Telescope Array, and is built by a consortium of Polish and Swiss institutions. The SST-1M will operate with DigiCam - an innovative, compact camera with fully digital read-out and trigger electronics. A high level of integration will be achieved by massively deploying state-of-the-art multi-gigabit transmission channels, beginning from the ADC flash converters, through the internal data and trigger signals transmission over backplanes and cables, to the camera's server link. Such an approach makes it possible to design the camera to fit the size and weight requirements of the SST-1M exactly, and provide low power consumption, high reliability and long lifetime. The structure of the digital electronics will be presented, along with main physical building blocks and the internal architecture of FPGA functional subsystems.

astro-ph.IM

Design, optimization and characterization of the light concentrators of the single-mirror small size telescopes of the Cherenkov Telescope Array

The focal-plane camera of $γ$-ray telescopes frequently uses light concentrators in front of light sensors. The purpose of these concentrators is to increase the effective area of the camera as well as to reduce the stray light coming at large incident angles. These light concentrators are usually based on the Winston cone design. In this contribution we present the design of an hexagonal hollow light concentrator with a lateral profile optimized using a cubic Bézier function to achieve a higher collection efficiency in the angular region of interest. The design presented here is optimized for a Davies-Cotton telescope with primary mirror of about 4 meters of diameter and focal length of 5.6 m. The described concentrators are part of an innovative camera made up of silicon-photomultipliers sensors, although a similar approach can be used for other sizes of single-mirror telescopes with different camera sensors, including photomultipliers. The challenge of our approach is to achieve a cost-effective design suitable for standard industrial productions of both the plastic concentrator substrate and the reflective coating. At the same time we maximize the optical performance. In this paper we also describe the optical set-up to measure the absolute collection efficiency of the light guides and demonstrate our good understanding of the measured data using a professional light tracing simulation.

astro-ph.IM

4 m Davies-Cotton telescope for the Cherenkov Telescope Array

The Cherenkov Telescope Array (CTA) is the next generation very high energy gamma-ray observatory. It will consist of three classes of telescopes, of large, medium and small sizes. The small telescopes, of 4 m diameter, will be dedicated to the observations of the highest energy gamma-rays, above several TeV. We present the technical characteristics of a single mirror, 4 m diameter, Davies-Cotton telescope for the CTA and the performance of the sub-array consisting of the telescopes of this type. The telescope will be equipped with a fully digital camera based on custom made, hexagonal Geiger-mode avalanche photodiodes. The development of cameras based on such devices is an RnD since traditionally photomultipliers are used. The photodiodes are now being characterized at various institutions of the CTA Consortium. Glass mirrors will be used, although an alternative is being considered: composite mirrors that could be adopted if they meet the project requirements. We present a design of the telescope structure, its components and results of the numerical simulations of the telescope performance.

astro-ph.IM