arXiv subjects

M. Teshima

Publications and source records attributed to M. Teshima.

At least 19 recordsLinked to original sources

arXiv2025

Development and Quality Control of PMT Modules for the Large-Sized Telescopes of the Cherenkov Telescope Array Observatory

The camera of the Large-Sized Telescopes (LSTs) of the Cherenkov Telescope Array Observatory (CTAO) consists of 1855 pixels that are grouped into 265 high-performance photomultiplier tube (PMT) modules. Each module comprises a seven-light-guide plate, seven PMT units, a slow control board, and a readout board with a trigger board. %In this paper we describe The requirements for the PMT modules include various aspects, such as photon detection efficiency, dynamic range, buffer depth, and test pulse functionality. We have developed a high-performance PMT module that fulfills all these requirements. Mass-production and quality control (QC) of modules for all four LSTs of the northern CTAO have been completed. Here we report on the technical details of each element of the module and its performance, together with the methods and results of QC measurements.

astro-ph.IM↗

arXiv2024

Direct Comparison of SiPM and PMT Sensor Performances in a large-size imaging air Cherenkov telescope

The peak photon detection efficiency (PDE) of silicon photomultipliers (SiPMs) can be as good or better than the PDE of photomultiplier tubes (PMTs). There are experiments where the signal is measured in the presence of a strong, steady background light emission. In these, one needs to accurately evaluate the signal-to-noise ratio. Imaging Atmospheric Cherenkov Telescopes (IACTs) observe in the presence of strong noise induced by the light of the night sky. It is certainly interesting to investigate the SiPM performance under operational conditions of IACTs and to compare it with that of the PMTs. For that purpose, we built a SiPM-based detector module, which was installed in one of the imaging cameras of the two Major Atmospheric Gamma-ray Imaging Cherenkov (MAGIC) telescopes in 2015. The experience gained from that module was used to design the second generation of modules of improved performance. Two such modules were installed in 2017. MAGIC is a system of two IACTs located on the Canary Island of La Palma. The mechanical structure of the MAGIC imaging cameras offers the possibility to install up to 6 additional detector modules of 7 pixels each into the open vertices of the hexagonal-shaped camera. This allows us to directly, without making any assumption, compare the performance of the PMT-based modules with that of the SiPM-based prototype modules, where SiPMs from three different manufacturers are used.

astro-ph.IM↗

arXiv2022

Performance Evaluation of Three Silicon Photomultiplier Detector Modules within the MAGIC Telescopes PMT-based camera

MAGIC is a system of two imaging atmospheric Cherenkov telescopes (IACTs) located on the Canary island of La Palma. Each telescope's imaging camera consists of 1039 photomultiplier tubes (PMTs). We developed three detector modules based on silicon photomultipliers (SiPMs) of seven pixels each that are mechanically and electronically compatible with those used in the MAGIC camera. These prototype modules are installed next to the PMTs in the imaging camera and are operated in parallel. To achieve a similar active area per pixel we used seven to nine SiPMs for producing a composite pixel. The SiPM signals within one such pixel are actively summed up for retaining the fast signal pulse shapes. Two different PCB designs are tested for thermal performance. We present our simulations of Cherenkov and light of the night sky (LoNS) responses. Based on those we calculate the signal-to-noise ratio (SNR) for this imaging application. We compare our expectations with the measurements of one of the SiPM-based detector modules.

astro-ph.IM↗

arXiv2018

A Technique for Estimating the Absolute Gain of a Photomultiplier Tube

Detection of low-intensity light relies on the conversion of photons to photoelectrons, which are then multiplied and detected as an electrical signal. To measure the actual intensity of the light, one must know the factor by which the photoelectrons have been multiplied. To obtain this amplification factor, we have developed a procedure for estimating precisely the signal caused by a single photoelectron. The method utilizes the fact that the photoelectrons conform to a Poisson distribution. The average signal produced by a single photoelectron can then be estimated from the number of noise events, without requiring analysis of the distribution of the signal produced by a single photoelectron. The signal produced by one or more photoelectrons can be estimated experimentally without any assumptions. This technique, and an example of the analysis of a signal from a photomultiplier tube, are described in this study.

astro-ph.IM↗

arXiv2016

Large Size Telescope Report

The Cherenkov Telescope Array (CTA) observatory will be deployed over two sites in the two hemispheres. Both sites will be equipped with four Large Size Telescopes (LSTs), which are crucial to achieve the science goals of CTA in the 20-200 GeV energy range. Each LST is equipped with a primary tessellated mirror dish of 23 m diameter, supported by a structure made mainly of carbon fibre reinforced plastic tubes and aluminum joints. This solution guarantees light weight (around 100 tons), essential for fast repositioning to any position in the sky in <20 seconds. The camera is composed of 1855 photomultiplier tubes and embeds the control, readout and trigger electronics. The detailed design is now complete and production of the first LST, which will serve as a prototype for the remaining seven, is ongoing. The installation of the first LST at the Roque de los Muchachos Observatory on the Canary island of La Palma (Spain) started in July 2016. In this paper we will outline the technical solutions adopted to fulfill the design requirements, present results of element prototyping and describe the installation and operation plans.

astro-ph.IM↗

arXiv2015

Development of Slow Control Boards for the Large Size Telescopes of the Cherenkov Telescope Array

The camera of the Large Size Telescopes (LSTs) of the Cherenkov Telescope Array (CTA) consists of 265 photosensor modules, each of them containing 7 photomultiplier tubes (PMTs), a slow control board (SCB), a readout board, and a trigger logic. We have developed the SCB, which is installed between the 7 PMTs and the readout board. The main task for SCBs is the controlling of the high voltages for the PMTs and the monitoring of their anode currents. In addition, the SCB provides the functionality to create test pulses that can be injected at the input of the PMT preamplifier in order to emulate a PMT signal without the need of setting a high voltage, or even without the PMT itself. The test pulses have a very similar width as the PMT pulses (less than 3 ns FWHM) and their amplitude can be adjusted in a wide dynamic range. These features allow us not only to test the functionality of the camera modules but also to fully characterize these. We report on the design and the functions of the SCB together with the results of test measurements.

astro-ph.IM↗

arXiv2015

The Optical System for the Large Size Telescope of the Cherenkov Telescope Array

The Large Size Telescope (LST) of the Cherenkov Telescope Array (CTA) is designed to achieve a threshold energy of 20 GeV. The LST optics is composed of one parabolic primary mirror 23 m in diameter and 28 m focal length. The reflector dish is segmented in 198 hexagonal, 1.51 m flat to flat mirrors. The total effective reflective area, taking into account the shadow of the mechanical structure, is about 368 m$^2$. The mirrors have a sandwich structure consisting of a glass sheet of 2.7 mm thickness, aluminum honeycomb of 60 mm thickness, and another glass sheet on the rear, and have a total weight about 47 kg. The mirror surface is produced using a sputtering deposition technique to apply a 5-layer coating, and the mirrors reach a reflectivity of $\sim$94% at peak. The mirror facets are actively aligned during operations by an active mirror control system, using actuators, CMOS cameras and a reference laser. Each mirror facet carries a CMOS camera, which measures the position of the light spot of the optical axis reference laser on the target of the telescope camera. The two actuators and the universal joint of each mirror facet are respectively fixed to three neighboring joints of the dish space frame, via specially designed interface plate.

astro-ph.IM↗

arXiv2015

Status of the Cherenkov Telescope Array's Large Size Telescopes

The Cherenkov Telescope Array (CTA) observatory, will be deployed over two sites in the two hemispheres. Both sites will be equipped with four Large Size Telescopes (LSTs), which are crucial to achieve the science goals of CTA in the 20-200 GeV energy range. Each LST is equipped with a primary tessellated mirror dish of 23 m diameter, supported by a structure made mainly of carbon fibre reinforced plastic tubes and aluminum joints. This solution guarantees light weight (around 100 tons), essential for fast repositioning to any position in the sky in <20 seconds. The camera is composed of 1855 PMTs and embeds the control, readout and trigger electronics. The detailed design is now complete and production of the first LST, which will serve as a prototype for the remaining seven, is well underway. In 2016 the first LST will be installed at the Roque de los Muchachos Observatory on the Canary island of La Palma (Spain). In this talk we will outline the technical solutions adopted to fulfill the design requirements, present results of element prototyping and describe the installation and operation plans.

astro-ph.IM↗

arXiv2014

Status of the new Sum-Trigger system for the MAGIC telescopes

MAGIC is a stereoscopic system of two 17m diameter Imaging Air Cherenckov Telescopes (IACTs) for $γ$-ray astronomy. Lowering the energy threshold of IACTs is crucial for the observation of Pulsars, high redshift AGNs and GRBs. A lower threshold compared to conventional digital trigger can be achieved by means of a novel concept, the so called Sum-Trigger, based on the analogue sum of a patch of pixels. The Sum-Trigger principle has been proven experimentally in 2007 by decreasing the energy threshold of the first MAGIC telescope from 55GeV down to 25GeV. The first VHE detection of the Crab Pulsar was achieved due to this low threshold. After the upgrade of the MAGIC I and MAGIC II, a new Sum-Trigger system will be installed in both telescopes in Summer 2013. The expected trigger threshold in stereo mode is about 25$÷$30GeV. It is a an improvement over the existing threshold (about 50GeV) of the digital trigger. We will report about the current status of the project.

astro-ph.IM↗

arXiv2013

Status of the technologies for the production of the Cherenkov Telescope Array (CTA) mirrors

The Cherenkov Telescope Array (CTA) is the next generation very high-energy gamma-ray observatory, with at least 10 times higher sensitivity than current instruments. CTA will comprise several tens of Imaging Atmospheric Cherenkov Telescopes (IACTs) operated in array-mode and divided into three size classes: large, medium and small telescopes. The total reflective surface could be up to 10,000 m2 requiring unprecedented technological efforts. The properties of the reflector directly influence the telescope performance and thus constitute a fundamental ingredient to improve and maintain the sensitivity. The R&D status of lightweight, reliable and cost-effective mirror facets for the CTA telescope reflectors for the different classes of telescopes is reviewed in this paper.

astro-ph.IM↗

arXiv2013

Mirror Development for the Cherenkov Telescope Array

The Cherenkov Telescope Array (CTA) is a planned observatory for very-high energy gamma-ray astronomy. It will consist of several tens of telescopes of different sizes, with a total mirror area of up to 10,000 square meters. Most mirrors of current installations are either polished glass mirrors or diamond-turned aluminium mirrors, both labour intensive technologies. For CTA, several new technologies for a fast and cost-efficient production of light-weight and reliable mirror substrates have been developed and industrial pre-production has started for most of them. In addition, new or improved aluminium-based and dielectric surface coatings have been developed to increase the reflectance over the lifetime of the mirrors compared to those of current Cherenkov telescope instruments.

astro-ph.IM↗

arXiv2013

Development of the Photomultiplier-Tube Readout System for the CTA Large Size Telescope

We have developed a prototype of the photomultiplier tube (PMT) readout system for the Cherenkov Telescope Array (CTA) Large Size Telescope (LST). Two thousand PMTs along with their readout systems are arranged on the focal plane of each telescope, with one readout system per 7-PMT cluster. The Cherenkov light pulses generated by the air showers are detected by the PMTs and amplified in a compact, low noise and wide dynamic range gain block. The output of this block is then digitized at a sampling rate of the order of GHz using the Domino Ring Sampler DRS4, an analog memory ASIC developed at Paul Scherrer Institute. The sampler has 1,024 capacitors per channel and four channels are cascaded for increased depth. After a trigger is generated in the system, the charges stored in the capacitors are digitized by an external slow sampling ADC and then transmitted via Gigabit Ethernet. An onboard FPGA controls the DRS4, trigger threshold, and Ethernet transfer. In addition, the control and monitoring of the Cockcroft-Walton circuit that provides high voltage for the 7-PMT cluster are performed by the same FPGA. A prototype named Dragon has been developed that has successfully sampled PMT signals at a rate of 2 GHz, and generated single photoelectron spectra.

astro-ph.IM↗

arXiv2011

Light Sensor Candidates for the Cherenkov Telescope Array

We report on the characterization of candidate light sensors for use in the next-generation Imaging Atmospheric Cherenkov Telescope project called Cherenkov Telescope Array, a major astro-particle physics project of about 100 telescopes that is currently in the prototyping phase. Our goal is to develop with the manufacturers the best possible light sensors (highest photon detection efficiency, lowest crosstalk and afterpulsing). The cameras of those telescopes will be based on classical super-bi-alkali Photomultiplier tubes but also Silicon Photomultipliers are candidate light sensors. A full characterisation of selected sensors was done. We are working in close contact with several manufacturers, giving them feedback and suggesting improvements.

astro-ph.IM↗

arXiv2011

Field test of the hybrid photodetector R9792U-40 on the MAGIC camera

The hybrid photodetector (HPD) R9792U-40 has very high peak quantum efficiency ($>50$% at 500 nm), excellent charge resolution and very low after-pulsing probability (500 times less than that of currently used photomultipliers (PMTs)). These features will improve the sensitivity, the energy resolution and the energy threshold of the MAGIC telescope. On the other hand, its high photocathode voltage (-8 to -6 kV), relatively short photocathode lifetime, and relatively large temperature dependence of the gain need to be taken care of. In February 2010, 6 HPDs were installed in a corner of the MAGIC-II camera for a field test. Here we report the results of the field test and our future plans.

astro-ph.IM↗

arXiv2010

Laser Acceleration toward PeV Feeling the Texture of Vacuum

Identified is a set of ballpark parameters for laser, plasma, and accelerator technologies that are defined for accelerated electron energies reaching as high as PeV. These parameters are carved out from the scaling laws that govern the physics of laser acceleration, theoretically suggested and experimentally explored over a wide range in the recent years. We extrapolate this knowledge toward PeV energies. In the density regime on the order of 10^16 cm^-3, it is possible to consider the application of the existing NIF (or LMJ) or its extended lasers to their appropriate retrofitting for this purpose. Although the ambition of luminosity is not pursued, such energies by themselves may allow us to begin to feel and study the physics of the 'texture of vacuum'. This is an example of fundamental physics exploration without the need of luminosity paradigm. By converting accelerated electrons with extreme energies to like energy gamma photons, and let them propagate through vacuum over a sufficient distance, these extremely high energy (and therefore short wavelength) photons experience smallest vacuum structures and fluctuations. If we can measure the arrival time differential and thus the gamma photon speed as a function of different energies such as 0.1 PeV vs 1 PeV, say within attoseconds accuracy, we can collect valuable data if and how gamma photons still obeys the premise of relativity or the vacuum texture begins to alter such fundamentals. The only method currently available to look at this problem may be to study astrophysical data of the primordial gamma ray bursts (GRBs), which are compared with the presently suggested approach.

physics.plasm-ph↗

arXiv2009

JEM-EUSO Science Objectives

JEM-EUSO, on board of the Japanese Exploration Module of the International Space Station, is being proposed as the first space observatory devoted to UHECR. Its privileged position at 430 km above the Earth surface, combined with a large field of view, innovative optics and a high efficiency focal surface, results in an unprecedented exposure which significantly surpasses that of the largest ground observatories. The large number of events expected above the GZK threshold for photo-pion production by protons will allow the directional identification of individual sources and the determination of their spectra, i.e., doing astronomy and astrophysics through the particle channel. Similar goals can be achieved in the case of light UHECR nuclei. Furthermore, the atmospheric target volume ($\sim 10^{12}$ ton) makes the possibility of neutrino observation a highlight of the mission. Other exploratory objectives include the detection of extreme energy gammas and the study of Galactic magnetic fields as well as global observations of the earth's atmosphere, including clouds, night-glows, plasma discharges, and meteors. In this contribution we will describe the scientific objectives of JEM-EUSO.

astro-ph.HE↗

arXiv2009

Hadron-gamma discrimination from an orbital UHECR observatory

The identification of very high energy photons is of great importance for the understanding of the origin of extreme energy cosmic rays (EECR). Several can be the sources of high energy photons at Earth. A guaranteed component is the flux of high energy photons expected as a consequence of the interaction of cosmic rays with the cosmic photon background. Another contribution may be expected as by-product at the acceleration sites of protons and nuclei, although such flux should be strongly suppressed for distant sources. On the other hand, top-down scenarios involving the decay of super heavy relic particles or topological defects, even if not currently favored, have as a characteristic signature an increasingly dominant flux of photons at the highest energies. In this work we study the statistical separation between hadron and photon showers at energies where both, LPM effect and magnetospheric interactions are important for the development of the cascades. We consider a detector with the same orbital characteristics as JEM-EUSO, but disregard trigger and reconstruction efficiencies, in order to define the maximum ideal discrimination power attainable.

astro-ph.HE↗

arXiv2009

Development of neutrino initiated cascades at mid and high altitudes in the atmosphere

Neutrinos are a very promising messenger at tens of EeV and above. They can be produced by several channels, namely as by products of hadronic interactions at the sources, as the main products of the decay of super massive particles and, in a guaranteed way, as the result of the propagation of UHECR through the bath of microwave relic photons. A new era of very large exposure space observatories, of which the JEM-EUSO mission is a prime example, is on the horizon and, with it, it is even larger the possibility of astrophysical neutrino detection at the highest energies. In the present work we use a combination of the PYTHIA interaction code with the CONEX shower simulation package in order to produce fast one-dimensional simulations of neutrino initiated showers in air. We make a detail study of the structure of the corresponding longitudinal profiles, but focus our physical analysis mainly on the development of showers at mid and high altitudes, where they can be an interesting target for space fluorescence observatories.

astro-ph.HE↗