arXiv subjects

Maclean Rouble

Publications and source records attributed to Maclean Rouble.

7 recordsLinked to original sources

arXiv2026

Tunable responsivity and bandwidth in microwave kinetic inductance detectors via readout current nonlinearity

Microwave kinetic inductance detectors (MKIDs) are generally read out with microwave readout tones of high enough amplitude to adequately suppress the noise contribution of the first-stage amplifier. At high readout power, the detector's resonant frequency is altered as a result of the dependence of the kinetic inductance on the internally circulating microwave current. With the tone placed below the resonant frequency, the nonlinear frequency shift results in a positive feedback effect that can significantly enhance the responsivity of the detector, to both optical and microwave power. We report a factor of 10 enhancement in optical response by tuning the readout power and frequency to close to the resonator's bifurcation point. A corresponding decrease in the bandwidth of the resonator is observed under these conditions. We show that the strength of the feedback effect can be easily selected by adjusting the excitation, and provide a map of possible operational states to do so. Operation of MKIDs in this mode could be used to improve sensitivity when non-intrinsic noise sources are significant.

cond-mat.supr-con↗

arXiv2025

In-situ control of the resonant frequency of kinetic inductance detectors with multiplexed readout

Large multiplexing factors are a primary advantage of kinetic inductance detectors (KIDs), but the implementation of high density arrays still presents significant challenges. Deviations between designed and achieved resonant frequencies are common, and differential loading and responsivity variation across an array may lead to dynamic inter-resonator interactions. It is therefore valuable to be able to both set and maintain the resonant frequency of a KID in situ, using the readout system. We show that it is possible to alter the resonant frequency of the devices by multiple linewidths through the application of readout current, and establish a new stable operational bias point at the driven frequency by making use of the hysteretic bistability commonly seen as bifurcation in frequency-domain measurements. We examine this interaction using a readout tone at fixed frequency positioned near or within the unbiased resonant bandwidth. Development of a control methodology based on this principle remains in an early stage, but a foundational step is understanding the interaction of the readout current with the resonator, in particular its influence on the resonant frequency. In this work, we study conventional KIDs with no physical isolation from the substrate, so we posit that the readout current primarily interacts with the resonator via non-thermal mechanisms, resulting in a predominantly reactive response. This behaviour is reproduced by a simple lumped-element circuit model of the resonance and readout system, providing a straightforward framework for analysis and interpretation. This demonstration is an important early step in the development of techniques which seek to dynamically alter the resonant frequencies of conventional KID arrays, and sets the stage for fast active resonant frequency control under operational conditions.

physics.ins-det↗

arXiv2024

A first demonstration of active feedback control and multi-frequency imaging techniques for kinetic inductance detectors

RF-ICE is a signal processing platform for the readout of large arrays of superconducting resonators. Designed for flexibility, the system's low digital latency and ability to independently and dynamically set the frequency and amplitude of probe tones in real time has enabled previously-inaccessible views of resonator behaviour, and opened the door to novel resonator control schemes. We introduce a multi-frequency imaging technique, developed with RF-ICE, which allows simultaneous observation of the entire resonance bandwidth. We demonstrate the use of this technique in the examination of the response of superconducting resonators to variations in applied readout current and thermal loading. We observe that, used in conjunction with a conventional frequency sweep at sufficiently large amplitude to induce resonance bifurcation, the multi-frequency imaging technique reveals a resonator response which is not captured by the frequency sweep measurement alone. We demonstrate that equivalent resonant frequency shifts can be achieved using either thermal, optical, or readout loading, and use this equivalence to counteract a change in thermal loading by digitally modulating the readout current through a resonator. We develop and implement a proof-of-concept closed-loop negative electro-quasiparticle feedback algorithm which first sets and then maintains the resonant frequency of a lumped element kinetic inductance detector while the loading on it is varied. Although this simple implementation is not yet suitable to deploy at scale, it demonstrates the utility of this feedback technique to improve linearity while addressing amplifier distortion, resonator response non-uniformity, and crosstalk. It can be applied to kinetic inductors in non-bolometric operation, and sets the stage for future developments.

astro-ph.IM↗

arXiv2024

The CRS: a scalable full-stack control system for Microwave Kinetic Inductance Detectors

The t0.technology Control and Readout System (CRS) is a modular microwave control and readout system for mm-wave and radio astronomy, THz imaging, noise radar, and superconducting qubit control. The configuration discussed in this work implements firmware for readout of microwave Kinetic Inductance Detector (KID) arrays. The CRS can operate 4,096 KIDs over 2.5 GHz of complex bandwidth between 0-10 GHz, typically allocated across four independent RF chains at 1,024x multiplexing and 625 MHz of complex bandwidth each. Every CRS can operate as a standalone unit or collectively within one or more backplane-enabled subracks that distribute power, clocking, and synchronization, scaling to an arbitrary number of channels. Each fully populated subrack supports arrays of more than 65,000 KIDs. The signal processing and control software supports recent innovations in multi-probe measurements and dynamic feedback modes, which are described in (Rouble et al. 2024). The CRS has recently been selected as the new baseline readout system for the proposed South Pole Telescope instrument, SPT-3G+. We present the hardware design, firmware capabilities, open-source control and data acquisition software, and the first laboratory characterization measurements.

astro-ph.IM↗

arXiv2023

Characterization of MKIDs for CMB observation at 220 GHz with the South Pole Telescope

We present an updated design of the 220 GHz microwave kinetic inductance detector (MKID) pixel for SPT-3G+, the next-generation camera for the South Pole Telescope. We show results of the dark testing of a 63-pixel array with mean inductor quality factor $Q_i = 4.8 \times 10^5$, aluminum inductor transition temperature $T_c = 1.19$ K, and kinetic inductance fraction $\alpha_k = 0.32$. We optically characterize both the microstrip-coupled and CPW-coupled resonators, and find both have a spectral response close to prediction with an optical efficiency of $\eta \sim 70\%$. However, we find slightly lower optical response on the lower edge of the band than predicted, with neighboring dark detectors showing more response in this region, though at level consistent with less than 5\% frequency shift relative to the optical detectors. The detectors show polarized response consistent with expectations, with a cross-polar response of $\sim 10\%$ for both detector orientations.

astro-ph.IM↗

arXiv2021

Development of MKIDs for measurement of the Cosmic Microwave Background with the South Pole Telescope

We present details of the design, simulation, and initial test results of prototype detectors for the fourth-generation receiver of the South Pole Telescope (SPT). Optimized for the detection of key secondary anisotropies of the cosmic microwave background (CMB), SPT-3G+ will measure the temperature and polarization of the mm/sub-mm sky at 220, 285, and 345 GHz, beyond the peak of the CMB blackbody spectrum. The SPT-3G+ focal plane will be populated with microwave kinetic inductance detectors (MKIDs), allowing for significantly increased detector density with reduced cryogenic complexity. We present simulation-backed designs for single-color dual-polarization MKID pixels at each SPT-3G+ observation frequency. We further describe design choices made to promote resonator quality and uniformity, enabling us to maximize the available readout bandwidth. We also discuss aspects of the fabrication process that enable rapid production of these devices and present an initial dark characterization of a series of prototype devices.

astro-ph.IM↗

arXiv2020

WinterLab: Developing a low-cost, portable experiment platform to encourage engagement in the electronics lab

Encouraging student engagement is a key aim in any educational setting, and allowing students the freedom to pursue their own methods of solving problems through independent experimentation has been shown to markedly improve this. In many contexts, however, allowing students this flexibility in their learning is hampered by constraints of the material itself, such as in the electronics laboratory, where expensive and bulky equipment confines the learning environment to the laboratory room. Finding ourselves in the position of teaching one such laboratory course at the undergraduate level, we sought to encourage students to learn through independent investigation and the pursuit of personal projects, by providing a more flexible and inquiry-based learning environment and allowing them to take their measurement equipment -- and their learning -- beyond the laboratory itself. We present this project as a case of design both for and by students, with the lead designer undertaking the project after attending the course in question, and pursuing its development as a foundational step in their graduate career. We discuss the challenges and opportunities we encountered over the course of the design and development process, and the eventual key output of the project: a portable, low-cost, integrated electronics experimentation platform called the Winterlab board.

physics.ed-ph↗