arXiv subjects

Mahesh P. Burse

Publications and source records attributed to Mahesh P. Burse.

12 recordsLinked to original sources

arXiv2018

Noise Characterization of IUCAA Digital Sampling Array Controller (IDSAC)

IUCAA Digital Sampling Array Controller (IDSAC) is a flexible and generic yet powerful CCD controller which can handle a wide range of scientific detectors. Based on an easily scalable modular backplane architecture consisting of Single Board Controllers (SBC), IDSAC can control large detector arrays and mosaics. Each of the SBCs offers the full functionality required to control a CCD independently. The SBCs can be cold swapped without the need to reconfigure them. Each SBC can handle data from up to four video channels with or without dummy outputs at speeds up to 500 kilo Pixels Per Second (kPPS) Per Channel with a resolution of 16 bits. Communication with Linux based host computer is through a USB3.0 interface, with the option of using copper or optical fibers. A Field Programmable Gate Array (FPGA) is used as the master controller in each SBC which allows great flexibility in optimizing performance by adjusting gain, timing signals, bias levels, etc. using user-editable configuration files without altering the circuit topology. Elimination of thermal kTC noise is achieved via Digital Correlated Double Sampling (DCDS). We present the results of noise performance characterization of IDSAC through simulation, theoretical modeling, and actual measurements. The contribution of different types of noise sources is modeled using a tool to predict noise of a generic DCDS signal chain analytically. The analytical model predicts the net input referenced noise of the signal chain to be 5 electrons for 200k pixels per second per channel readout rate with 3 samples per pixel. Using a cryogenic test set up in the lab, the noise is measured to be 5.4 e (24.3 \muV), for the same readout configuration.

astro-ph.IM↗

arXiv2018

IDSAC - IUCAA Digital Sampler Array Controller

IUCAA Digital Sampling Array Controller (IDSAC) is a generic CCD Controller which is flexible and powerful enough to control a wide variety of CCDs and CMOS detectors used for ground-based astronomy. It has a fully scalable architecture, which can control multiple CCDs and can be easily expanded. The controller has a modular backplane architecture consists of Single Board Controller Cards (SBCs) and can control a mosaic or independent of 5 CCDs. Key features of IDSAC contains usage of FPGA as a reconfigurable master controller, implementation of Digital CDS to achieve low noise and ability to process upto four CCD output at 1Mpixels/Sec/Channel with 16-bit resolution. The best feature of IDSAC is it uses the technique of Digital Correlated Double Sampling(DCDS). It is known that CCD video output is dominated by thermal KTC noise contributed from the summing well capacitor of the CCD output circuitry. To eliminate thermal KTC noise Correlated Double Sampling (CDS) is a very standard technique. CDS performed in Digital domain (DCDS) has several advantages over its analog counterpart, such as - less electronics, faster readout and easier post processing. It is also flexible with sampling rate and pixel throughput while maintaining the core circuit topology intact. The noise characterization of the IDSAC CDS signal chain has been performed by analytical modelling, software simulation and practical measurements. Various types of noise such as white, pink, power supply, bias etc. has been considered while creating a analytical noise model tool to predict noise of a controller system like IDSAC. Standard test bench softwares like Pspice and Multisim are used to simulate the noise performance while several tests are performed to measure the actual noise of IDSAC.The theoretical calculation matches very well with component level simulation as well as practical measurements within 10% accuracy.

astro-ph.IM↗

arXiv2018

Scalable Platform for Adaptive optics Real-time Control (SPARC) Part 2: Field Programmable Gate Array (FPGA) implementation and performance

The next generation of Adaptive Optics (AO) systems on large telescopes will require immense computation performance and memory bandwidth, both of which are challenging with the technology available today. The objective of this work is to create a future-proof adaptive optics platform on an FPGA architecture, which scales with the number of subapertures, pixels per subaperture and external memory. We have created a scalable adaptive optics platform with an off-the-shelf FPGA development board, which provides an AO reconstruction time only limited by the external memory bandwidth. SPARC uses the same logic resources irrespective of the number of subapertures in the AO system. This paper is aimed at embedded developers who are interested in the FPGA design and the accompanying hardware interfaces. The central theme of this paper is to show how scalability is incorporated at different levels of the FPGA implementation. This work is a continuation of Part 1 of the paper which explains the concept, objectives, control scheme and method of validation used for testing the platform.

astro-ph.IM↗

arXiv2018

Scalable Platform for Adaptive optics Real-time Control (SPARC) Part 1: Concept, Architecture and Validation

We demonstrate a novel architecture for Adaptive Optics (AO) control based on FPGAs (Field Programmable Gate Arrays), making active use of their configurable parallel processing capability. SPARC's unique capabilities are demonstrated through an implementation on an off-the-shelf inexpensive Xilinx VC-709 development board. The architecture makes SPARC a generic and powerful Real-time Control (RTC) kernel for a broad spectrum of AO scenarios. SPARC is scalable across different numbers of subapertures and pixels per subaperture. The overall concept, objectives, architecture, validation and results from simulation as well as hardware tests are presented here. For Shack-Hartmann wavefront sensors, the total AO reconstruction time ranges from a median of 39.4us (11x11 subapertures) to 1.283 ms (50x50 subapertures) on the development board. For large wavefront sensors, the latency is dominated by access time (~1 ms) of the standard DDR memory available on the board. This paper is divided into two parts. Part 1 is targeted at astronomers interested in the capability of the current hardware. Part 2 explains the FPGA implementation of the wavefront processing unit, the reconstruction algorithm and the hardware interfaces of the platform. Part 2 mainly targets the embedded developers interested in the hardware implementation of SPARC.

astro-ph.IM↗

arXiv2015

Development of a scalable generic platform for adaptive optics real time control

The main objective of the present project is to explore the viability of an adaptive optics control system based exclusively on Field Programmable Gate Arrays (FPGAs), making strong use of their parallel processing capability. In an Adaptive Optics (AO) system, the generation of the Deformable Mirror (DM) control voltages from the Wavefront Sensor (WFS) measurements is usually through the multiplication of the wavefront slopes with a predetermined reconstructor matrix. The ability to access several hundred hard multipliers and memories concurrently in an FPGA allows performance far beyond that of a modern CPU or GPU for tasks with a well defined structure such as Adaptive Optics control. The target of the current project is to generate a signal for a real time wavefront correction, from the signals coming from a Wavefront Sensor, wherein the system would be flexible to accommodate all the current Wavefront Sensing techniques and also the different methods which are used for wavefront compensation. The system should also accommodate for different data transmission protocols (like Ethernet, USB, IEEE 1394 etc.) for transmitting data to and from the FPGA device, thus providing a more flexible platform for Adaptive Optics control. Preliminary simulation results for the formulation of the platform, and a design of a fully scalable slope computer is presented.

astro-ph.IM↗

arXiv2014

A survey of the high order multiplicity of nearby solar-type binary stars with Robo-AO

We conducted a survey of nearby binary systems composed of main sequence stars of spectral types F and G in order to improve our understanding of the hierarchical nature of multiple star systems. Using Robo-AO, the first robotic adaptive optics instrument, we collected high angular resolution images with deep and well-defined detection limits in the SDSS $i'$ band. A total of 695 components belonging to 595 systems were observed. We prioritized observations of faint secondary components with separations over $10''$ to quantify the still poorly constrained frequency of their sub-systems. Of the 214 secondaries observed, 39 contain such subsystems; 19 of those were discovered with Robo-AO. The selection-corrected frequency of secondary sub-systems with periods from $10^{3.5}$ to $10^5$ days is 0.12$\pm$0.03, the same as the frequency of such companions to the primary. Half of the secondary pairs belong to quadruple systems where the primary is also a close pair, showing that the presence of sub-systems in both components of the outer binary is correlated. The relatively large abundance of 2+2 quadruple systems is a new finding, and will require more exploration of the formation mechanism of multiple star systems. We also targeted close binaries with periods less than 100~yr, searching for their distant tertiary components, and discovered 17 certain and 2 potential new triples. In a sub-sample of 241 close binaries, 71 have additional outer companions. The overall frequency of tertiary components is not enhanced, compared to all (non-binary) targets, but in the range of outer periods from $10^6$ to $10^{7.5}$ days (separations on the order of 500~AU), the frequency of tertiary components is 0.16$\pm$0.03, exceeding by almost a factor of two the frequency of similar systems among all targets (0.09).

astro-ph.SR↗

arXiv2014

Robotic Laser-Adaptive-Optics Imaging of 715 Kepler Exoplanet Candidates using Robo-AO

The Robo-AO Kepler Planetary Candidate Survey is designed to observe every Kepler planet candidate host star with laser adaptive optics imaging to search for blended nearby stars, which may be physically associated companions and/or responsible for transit false positives. In this paper we present the results from the 2012 observing season, searching for stars close to 715 representative Kepler planet candidate hosts. We find 53 companions, 44 of which are new discoveries. We detail the Robo-AO survey data reduction methods including a method of using the large ensemble of target observations as mutual point-spread-function references, along with a new automated companion-detection algorithm designed for large adaptive optics surveys. Our survey is sensitive to objects from 0.15" to 2.5" separation, with contrast ratios up to delta-m~6. We measure an overall nearby-star-probability for Kepler planet candidates of 7.4% +/- 1.0%, and calculate the effects of each detected nearby star on the Kepler-measured planetary radius. We discuss several KOIs of particular interest, including KOI-191 and KOI-1151, which are both multi-planet systems with detected stellar companions whose unusual planetary system architecture might be best explained if they are "coincident multiple" systems, with several transiting planets shared between the two stars. Finally, we detect 2.6-sigma evidence for <15d-period giant planets being 2-3 times more likely be found in wide stellar binaries than smaller close-in planets and all sizes of further-out planets.

astro-ph.EP↗

arXiv2013

Bringing the Visible Universe into Focus with Robo-AO

Light from astronomical objects must travel through the earth's turbulent atmosphere before it can be imaged by ground-based telescopes. To enable direct imaging at maximum theoretical angular resolution, advanced techniques such as those employed by the Robo-AO adaptive-optics system must be used.

astro-ph.IM↗

arXiv2013

The Robo-AO software: Fully autonomous operation of a laser guide star adaptive optics and science system

Robo-AO is the first astronomical laser guide star adaptive optics (AO) system designed to operate completely independent of human supervision. A single computer commands the AO system, the laser guide star, visible and near-infrared science cameras (which double as tip-tip sensors), the telescope, and other instrument functions. Autonomous startup and shutdown sequences as well as concatenated visible observations were demonstrated in late 2011. The fully robotic software is currently operating during a month long demonstration of Robo-AO at the Palomar Observatory 60-inch telescope.

astro-ph.IM↗

arXiv2012

Millions of Multiples: Detecting and Characterizing Close-Separation Binary Systems in Synoptic Sky Surveys

The direct detection of binary systems in wide-field surveys is limited by the size of the stars' point-spread-functions (PSFs). A search for elongated objects can find closer companions, but is limited by the precision to which the PSF shape can be calibrated for individual stars. We have developed the BinaryFinder algorithm to search for close binaries by using precision measurements of PSF ellipticity across wide-field survey images. We show that the algorithm is capable of reliably detecting binary systems down to approximately 1/5 of the seeing limit, and can directly measure the systems' position angles, separations and contrast ratios. To verify the algorithm's performance we evaluated 100,000 objects in Palomar Transient Factory (PTF) wide-field-survey data for signs of binarity, and then used the Robo-AO robotic laser adaptive optics system to verify the parameters of 44 high-confidence targets. We show that BinaryFinder correctly predicts the presence of close companions with a <5% false-positive rate, measures the detected binaries' position angles within 2 degrees and separations within 25%, and weakly constrains their contrast ratios. When applied to the full PTF dataset, we estimate that BinaryFinder will discover and characterize ~450,000 physically-associated binary systems with separations <2 arcseconds and magnitudes brighter than R=18. New wide-field synoptic surveys with high sensitivity and sub-arcsecond angular resolution, such as LSST, will allow BinaryFinder to reliably detect millions of very faint binary systems with separations as small as 0.1 arcseconds.

astro-ph.SR↗

arXiv2011

Three New Eclipsing White-dwarf - M-dwarf Binaries Discovered in a Search for Transiting Planets Around M-dwarfs

We present three new eclipsing white-dwarf / M-dwarf binary systems discovered during a search for transiting planets around M-dwarfs. Unlike most known eclipsing systems of this type, the optical and infrared emission is dominated by the M-dwarf components, and the systems have optical colors and discovery light curves consistent with being Jupiter-radius transiting planets around early M-dwarfs. We detail the PTF/M-dwarf transiting planet survey, part of the Palomar Transient Factory (PTF). We present a Graphics Processing Unit (GPU)-based box-least-squares search for transits that runs approximately 8X faster than similar algorithms implemented on general purpose systems. For the discovered systems, we decompose low-resolution spectra of the systems into white-dwarf and M-dwarf components, and use radial velocity measurements and cooling models to estimate masses and radii for the white dwarfs. The systems are compact, with periods between 0.35 and 0.45 days and semimajor axes of approximately 2 solar radii (0.01 AU). We use the Robo-AO laser guide star adaptive optics system to tentatively identify one of the objects as a triple system. We also use high-cadence photometry to put an upper limit on the white dwarf radius of 0.025 solar radii (95% confidence) in one of the systems. We estimate that 0.08% (90% confidence) of M-dwarfs are in these short-period, post-common-envelope white-dwarf / M-dwarf binaries where the optical light is dominated by the M-dwarf. Similar eclipsing binary systems can have arbitrarily small eclipse depths in red bands and generate plausible small-planet-transit light curves. As such, these systems are a source of false positives for M-dwarf transiting planet searches. We present several ways to rapidly distinguish these binaries from transiting planet systems.

astro-ph.SR↗

arXiv2009

UNICS - An Unified Instrument Control System for Small/Medium Sized Astronomical Observatories

Although the astronomy community is witnessing an era of large telescopes, smaller and medium sized telescopes still maintain their utility being larger in numbers. In order to obtain better scientific outputs it is necessary to incorporate modern and advanced technologies to the back-end instruments and to their interfaces with the telescopes through various control processes. However often tight financial constraints on the smaller and medium size observatories limit the scope and utility of these systems. Most of the time for every new development on the telescope the back-end control systems are required to be built from scratch leading to high costs and efforts. Therefore a simple, low cost control system for small and medium size observatory needs to be developed to minimize the cost and efforts while going for the expansion of the observatory. Here we report on the development of a modern, multipurpose instrument control system UNICS (Unified Instrument Control System) to integrate the controls of various instruments and devices mounted on the telescope. UNICS consists of an embedded hardware unit called Common Control Unit (CCU) and Linux based data acquisition and User Interface. The Hardware of the CCU is built around the Atmel make ATmega 128 micro-controller and is designed with a back-plane, Master Slave architecture. The Graphical User Interface (GUI) has been developed based on QT and the back end application software is based on C/C++. UNICS provides feedback mechanisms which give the operator a good visibility and a quick-look display of the status and modes of instruments. UNICS is being used for regular science observations since March 2008 on 2m, f/10 IUCAA Telescope located at Girawali, Pune India.

astro-ph.IM↗