arXiv subjects

Makoto Tabata

Publications and source records attributed to Makoto Tabata.

18 recordsLinked to original sources

arXiv2019

Transparent tiles of silica aerogels for high-energy physics

Silica aerogels are important to be used as photon radiators in Cherenkov counters for high-energy-physics experiments because of their optical transparency and intermediate refractive indices between those of gases and liquids or solids. Cherenkov counters that employ silica aerogels as radiators and photodetectors are often used to identify subatomic charged particles (e.g., electrons, protons, and pions) with momenta on the order of sub-GeV/$c$ to GeV/$c$; they are also used to measure particle velocities in accelerator-based particle- and nuclear-physics experiments and in space- and balloon-borne experiments in the field of cosmic-ray physics. Recent studies have demonstrated that it is important for the design of Cherenkov counters that the transparent silica-aerogel tiles comprise solid material with recently improved transparency and a refractive index that can be controlled between 1.003 and 1.26 by varying the bulk density in the range of 0.01$-$1.0 g/cm$^3$. Additionally, a technique for fabricating large-area silica-aerogel tiles without cracking has been developed. In this chapter, we describe advances in the technologies for producing silica aerogels with high optical performances to be used in scientific instruments. We further discuss the principles underlying the operation of detectors based on the Cherenkov effect. We also review applications of silica aerogels in specific high-energy-physics experiments.

physics.ins-det↗

arXiv2019

Developing a silica aerogel radiator for the HELIX ring-imaging Cherenkov system

This paper reports the successful fabrication of silica aerogel Cherenkov radiators produced in the first batches from a 96-tile mass production performed using pin-drying technique in our laboratory. The aerogels are to be used in a ring-imaging Cherenkov detector in the spectrometer of a planned balloon-borne cosmic-ray observation program, HELIX (High Energy Light Isotope eXperiment). A total of 36 transparent, hydrophobic aerogel tiles with a high refractive index of 1.16 and dimensions of 10 cm $\times $ 10 cm $\times $ 1 cm will be chosen as the flight radiators. Thus far, 40 out of the 48 tiles fabricated were confirmed as having no tile cracking. In the first screening, 8 out of the first 16 tiles were accepted as flight-qualified candidates, based on basic optical measurement results. To fit the aerogel tiles into a radiator support structure, the trimming of previously manufactured prototype tiles using a water-jet cutting device was successful.

physics.ins-det↗

arXiv2016

Large-area silica aerogel for use as Cherenkov radiators with high refractive index, developed by supercritical carbon dioxide drying

This study presents the development of large-area (18 $\times $ 18 $\times $ 2 cm$^3$), high refractive index ($n \sim $1.05) hydrophobic silica aerogel tiles for use as Cherenkov radiators. These transparent aerogel tiles will be installed in a Cherenkov detector for the next-generation accelerator-based particle physics experiment Belle II, to be performed at the High Energy Accelerator Research Organization (KEK) in Japan. Cracking has been eliminated from the prototype aerogel tiles by improving the supercritical carbon dioxide (scCO$_2$) extraction procedure when drying the wet gel tiles. Finally, a method of mass-producing aerogel tiles for the actual detector was established. It was confirmed that the experimentally manufactured aerogel tiles meet the required optical and hydrophobic characteristics and have a uniform tile density.

physics.ins-det↗

arXiv2016

Ultralow-density double-layer silica aerogel fabrication for the intact capture of cosmic dust in low-Earth orbits

The fabrication of an ultralow-density hydrophobic silica aerogel for the intact capture cosmic dust during the Tanpopo mission is described. The Tanpopo experiment performed on the International Space Station orbiting the Earth includes the collection of terrestrial and interplanetary dust samples on a silica aerogel capture medium exposed to space for later ground-based biological and chemical analyses. The key to the mission's success is the development of high-performance capture media, and the major challenge is to satisfy the mechanical requirements as a spacecraft payload while maximizing the performance for intact capture. To this end, an ultralow-density (0.01 g cm$^{-3}$) soft aerogel was employed in combination with a relatively robust 0.03 g cm$^{-3}$ aerogel. A procedure was also established for the mass production of double-layer aerogel tiles formed with a 0.01 g cm$^{-3}$ surface layer and a 0.03 g cm$^{-3}$ open-topped, box-shaped base layer, and 60 aerogel tiles were manufactured. The fabricated aerogel tiles have been demonstrated to be suitable as flight hardware with respect to both scientific and safety requirements.

physics.ins-det↗

arXiv2015

Fabrication of silica aerogel with $n$ = 1.08 for $e^+/μ^+$ separation in a threshold Cherenkov counter of the J-PARC TREK/E36 experiment

This study presents the development of hydrophobic silica aerogel for use as a radiator in threshold-type Cherenkov counters. These counters are to be used for separating positrons and positive muons produced by kaon decay in the J-PARC TREK/E36 experiment. We chose to employ aerogel with a refractive index of 1.08 to identify charged particles with momenta of approximately 240 MeV/$c$, and the radiator block shape was designed with a trapezoidal cross-section to fit the barrel region surrounding the kaon stopping target in the center of the TREK/E36 detector system. Including spares, we obtained 30 crack-free aerogel blocks segmented into two layers, each layer having a thickness of 2 cm and a length of 18 cm, to fill 12 counter modules. Optical measurements showed that the produced aerogel tiles had the required refractive indices and transparency.

physics.ins-det↗

arXiv2015

Silica aerogel for capturing intact interplanetary dust particles for the Tanpopo experiment

In this paper, we report the progress in developing a silica-aerogel-based cosmic dust capture panel for use in the Tanpopo experiment on the International Space Station (ISS). Previous studies revealed that ultralow-density silica aerogel tiles comprising two layers with densities of 0.01 and 0.03 g/cm$^3$ developed using our production technique were suitable for achieving the scientific objectives of the astrobiological mission. A special density configuration (i.e., box framing) aerogel with a holder was designed to construct the capture panels. Qualification tests for an engineering model of the capture panel as an instrument aboard the ISS were successful. Sixty box-framing aerogel tiles were manufactured in a contamination-controlled environment.

physics.ins-det↗

arXiv2014

Assembly and bench testing of a spiral fiber tracker for the J-PARC TREK/E36 experiment

This study presents the recent progress made in developing a spiral fiber tracker (SFT) for use in the experiment TREK/E36 planned at the Japan Proton Accelerator Research Complex. This kaon decay experiment uses a stopped positive kaon beam to search for physics beyond the Standard Model through precision measurements of lepton universality and through searches for a heavy sterile neutrino and a dark photon. Detecting and tracking positrons and positive muons from kaon decays are of importance in achieving high-precision measurements; therefore, we designed and are developing the new tracking detector using a scintillating fiber. The SFT was completely assembled, and in a bench test, no dead channel was determined.

physics.ins-det↗

arXiv2014

Progress in developing a spiral fiber tracker for the J-PARC E36 experiment

This paper reports the recent progress made in developing a spiral fiber tracker (SFT) for use in the E36 experiment scheduled at the Japan Proton Accelerator Research Complex (J-PARC). The primary goal of this positive kaon decay experiment, which uses a stopped kaon beam, is to test lepton flavor universality to search for physics beyond the Standard Model of particle physics. For this experiment, we are currently upgrading the E246 apparatus, which consists of the superconducting toroidal spectrometer previously used at the High Energy Accelerator Research Organization (KEK), Japan. Conducting high-precision measurements will rely on efficiently detecting and tracking charged particles (i.e., positive muons and positrons) from kaon decays. Combined with the three existing layers of multiwire proportional chambers, the SFT comprises four layers of ribbons, with each layer containing 1-mm-diameter double-clad plastic scintillating fibers; the ribbons are spirally wound in two helicities around the kaon stopping target at the center of the detector system. Scintillation photons are read out by multipixel photon counters connected to the scintillating fibers by clear optical fiber extensions. A preliminary bench test shows that a prototype two-layer fiber ribbon exhibits 99.6% detection efficiency at the 1-photoelectron threshold. Finally, the SFT was successfully assembled around the target holder.

physics.ins-det↗

arXiv2014

Recent progress in the development of large area silica aerogel for use as RICH radiator in the Belle II experiment

We report recent progress in the development of large-area hydrophobic silica aerogels for use as radiators in the aerogel-based ring-imaging Cherenkov (A-RICH) counter to be installed in the forward end cap of the Belle II detector, which is currently being upgraded at the High Energy Accelerator Research Organization (KEK), Japan. The production of approximately 450 aerogel tiles with refractive indices of either 1.045 or 1.055 was completed in May, 2014, and the tiles are now undergoing optical characterization. Installation of the aerogels was tested by installing them into a partial mock-up of the support structure.

physics.ins-det↗

arXiv2014

Progress in development of silica aerogel for particle- and nuclear-physics experiments at J-PARC

This study presents the advancement in hydrophobic silica aerogel development for use as Cherenkov radiators and muonium production targets. These devices are scheduled for use in several particle- and nuclear-physics experiments that are planned in the near future at the Japan Proton Accelerator Research Complex. Our conventional method to produce aerogel tiles with an intermediate index of refraction of approximately 1.05 is extended so that we can now produce aerogel tiles with lower indices of refraction (i.e., 1.03-1.04) and higher indices of refraction (i.e., 1.075-1.08); each with excellent transparency. A new production method, called pin drying, was optimized to produce larger area aerogels consistently with an ultrahigh index of refraction (>1.10). In addition, for use as a thermal-muonium-emitting material at room temperature, dedicated low-density aerogels were fabricated using the conventional method.

physics.ins-det↗

arXiv2014

Silica aerogel radiator for use in the A-RICH system utilized in the Belle II experiment

This paper presents recent progress in the development and mass production of large-area hydrophobic silica aerogels for use as radiators in the aerogel-based ring-imaging Cherenkov (A-RICH) counter, which will be installed in the forward end cap of the Belle II detector. The proximity-focusing A-RICH system is especially designed to identify charged kaons and pions. The refractive index of the installed aerogel Cherenkov radiators is approximately 1.05, and we aim for a separation capability exceeding 4$σ$ at momenta up to 4 GeV/$c$. Large-area aerogel tiles (over 18 $\times $ 18 $\times $ 2 cm$^3$) were first fabricated in test productions by pin drying in addition to conventional methods. We proposed to fill the large end-cap region (area 3.5 m$^2$) with 124 water-jet-trimmed fan-shaped dual-layer-focusing aerogel combinations of different refractive indices (1.045 and 1.055). Guided by the test production results, we decided to manufacture aerogels by the conventional method and are currently proceeding with mass production. In an electron beam test undertaken at the DESY, we confirmed that the $K$/$π$ separation capability of a prototype A-RICH counter exceeded 4$σ$ at 4 GeV/$c$.

physics.ins-det↗

arXiv2014

Design of a silica-aerogel-based cosmic dust collector for the Tanpopo mission aboard the International Space Station

We are developing a silica-aerogel-based cosmic dust collector for use in the Tanpopo experiment to be conducted on the International Space Station. The mass production of simple two-layer hydrophobic aerogels was undertaken in a contamination-controlled environment, yielding more than 100 undamaged products. The collector, comprising an aerogel tile and holder panel, was designed to resist launch vibration and to conform to an exposure attachment. To this end, a box-framing aerogel with inner and outer densities of 0.01 and 0.03 g/cm$^3$, respectively, was fabricated. The aerogel mounted in the panel passed random vibration tests at the levels of the acceptance and qualification tests for launch. It also withstood the pressure changes expected in the airlock on the International Space Station.

physics.ins-det↗

arXiv2012

X-ray radiographic technique for measuring density uniformity of silica aerogel

This paper proposes a new X-ray radiographic technique for measuring density uniformity of silica aerogels used as radiator in proximity-focusing ring-imaging Cherenkov detectors. To obtain high performance in a large-area detector, a key characteristic of radiator is the density (i.e. refractive index) uniformity of an individual aerogel monolith. At a refractive index of n = 1.05, our requirement for the refractive index uniformity in the transverse plane direction of an aerogel tile is |δ(n - 1)/(n - 1)| < 4% in a focusing dual layer radiator (with different refractive indices) scheme. We applied the radiographic technique to evaluate the density uniformity of our original aerogels from a trial production and that of Panasonic products (SP-50) as a reference, and to confirm they have sufficient density uniformity within \pm 1% along the transverse plane direction. The measurement results show that the proposed technique can quantitatively estimate the density uniformity of aerogels.

physics.ins-det↗

arXiv2012

Optical and radiographical characterization of silica aerogel for Cherenkov radiator

We present optical and X-ray radiographical characterization of silica aerogels with refractive index from 1.05 to 1.07 for a Cherenkov radiator. A novel pin-drying method enables us to produce highly transparent hydrophobic aerogels with high refractive index by shrinking wet-gels. In order to investigate the uniformity in the density (i.e., refractive index) of an individual aerogel monolith, we use the laser Fraunhofer method, an X-ray absorption technique, and Cherenkov imaging by a ring imaging Cherenkov detector in a beam test. We observed an increase in density at the edge of the aerogel tiles, produced by pin-drying.

physics.ins-det↗

arXiv2012

Recent progress in silica aerogel Cherenkov radiator

In this paper, we present recent progress in the development of hydrophobic silica aerogel as a Cherenkov radiator. In addition to the conventional method, the recently developed pin-drying method for producing high-refractive-index aerogels with high transparency was studied in detail. Optical qualities and large tile handling for crack-free aerogels were investigated. Sufficient photons were detected from high-performance aerogels in a beam test.

physics.ins-det↗

arXiv2011

Tanpopo cosmic dust collector: Silica aerogel production and bacterial DNA contamination analysis

Hydrophobic silica aerogels with ultra-low densities have been designed and developed as cosmic dust capture media for the Tanpopo mission which is proposed to be carried out on the International Space Station. Glass particles as a simulated cosmic dust with 30 μm in diameter and 2.4 g/cm^3 in density were successfully captured by the novel aerogel at a velocity of 6 km/s. Background levels of contaminated DNA in the ultra-low density aerogel were lower than the detection limit of a polymerase chain reaction assay. These results show that the manufactured aerogel has good performance as a cosmic dust collector and sufficient quality in respect of DNA contamination. The aerogel is feasible for the biological analyses of captured cosmic dust particles in the astrobiological studies.

physics.ins-det↗

arXiv2011

Development of transparent silica aerogel over a wide range of densities

We have succeeded in developing hydrophobic silica aerogels over a wide range of densities (i.e. refractive indices). A pinhole drying method was invented to make possible producing highly transparent aerogels with entirely new region of refractive indices of 1.06-1.26. Obtained aerogels are more transparent than conventional ones, and the refractive index is well controlled in the pinhole drying process. A test beam experiment was carried out in order to evaluate the performance of the pinhole-dried aerogels as a Cherenkov radiator. A clear Cherenkov ring was successfully observed by a ring imaging Cherenkov counter. We also developed monolithic and hydrophobic aerogels with a density of 0.01 g/cm^3 (a low refractive index of 1.0026) as a cosmic dust capturer for the first time. Consequently, aerogels with any refractive indices between 1.0026 and 1.26 can be produced freely.

physics.ins-det↗

arXiv2011

Hydrophobic silica aerogel production at KEK

We present herein a characterization of a standard method used at the High Energy Accelerator Research Organization (KEK) to produce hydrophobic silica aerogels and expand this method to obtain a wide range of refractive index (n = 1.006-1.14). We describe in detail the entire production process and explain the methods used to measure the characteristic parameters of aerogels, namely the refractive index, transmittance, and density. We use a small-angle X-ray scattering (SAXS) technique to relate the transparency to the fine structure of aerogels.

physics.ins-det↗