arXiv subjects

Manny Montoya

Publications and source records attributed to Manny Montoya.

15 recordsLinked to original sources

arXiv2026

Upgrading LBTI/NOMIC with a quadruple annular groove phase mask and GeoSnap detector for imaging nearby, habitable-zone exoplanets

The Large Binocular Telescope Interferometer (LBTI)'s Nulling-Optimized Mid-Infrared Camera (NOMIC) is among the most capable thermal-infrared imaging systems available for high-contrast, high-angular-resolution astronomical observations. Here we describe two in-progress upgrades to LBTI/NOMIC: (1) the design, fabrication, and installation of a quadruple annular groove phase mask (Q-AGPM) coronagraph, and (2) the installation of a 13 micron-cutoff Teledyne GeoSnap array. The Q-AGPM is the first coronagraph to be installed within NOMIC and one of the first optimized for N-band (~11 micron) observations. It places four annular groove phase masks on a single diamond substrate so that, in the LBTI dual-aperture imaging mode, each of the two telescope beams can be chopped between a pair of masks without loss of observing efficiency. The GeoSnap array will replace NOMIC's original AQUARIUS array, delivering higher quantum efficiency, larger well depth, faster and more linear readout, and freedom from the excess low-frequency noise that requires aggressive chopping. Together these upgrades substantially improve the achievable contrast and sensitivity at small angular separations. We also present a high-contrast Fizeau imaging sequence obtained with LBTI's new FFTCam fringe tracker, which confirms the interferometric gain over a single aperture through injection/recovery tests: relative to an equal-time single aperture exposure, the S/N = 3 contrast is a factor of ~2-4 deeper across 0.2-1 arcsec, spanning the contrast- and background-limited regimes. Finally, we describe the role of the upgraded LBTI/NOMIC instrument within the Breakthrough Watch program at the University of Arizona, which aims to perform the deepest observations yet of the habitable zones of the nearest single Sun-like stars.

astro-ph.IM↗

arXiv2025

MIRAC-5 on the MMT with MAPS: annular groove phase mask N-band coronagraphic upgrade

We describe the coronagraphic upgrade underway for the Mid-Infrared Array Camera-5 (MIRAC-5) to be used with the 6.5-m MMT telescope utilizing the new MMT Adaptive optics exoPlanet characterization System (MAPS). Mid-IR ground-based coronagraphic adaptive-optics-assisted imaging can be a powerful tool for characterizing exoplanet atmospheres and studying protoplanets in formation within circumstellar disks around young stars. In addition to enabling ground-based observations of bright targets in the background limit, high actuator density 1-2 kHz adaptive optics systems can be competitive with JWST in the contrast limit. We have procured an annular groove phase mask (AGPM) and performed preliminary characterization of its on-axis source rejection as a function of wavelength. We present an optimized Lyot Stop design for use with the AGPM using the High-contrast End-to-End Performance Simulator (HEEPS). Future work includes implementing the Quadrant Analysis of Coronagraphic Images for Tip-tilt Sensing (QACITS) control loop algorithm with MAPS. We present the system overview, pupil mask design, and expected performance metrics aligned with our scientific goals, building upon recent advances with MIRAC-5 (Bowens et al. 2025) and MAPS.

astro-ph.IM↗

arXiv2024

Commissioning of the MIRAC-5 Mid-Infrared Instrument on the MMT

We present results from commissioning observations of the mid-IR instrument, MIRAC-5, on the 6.5-m MMT telescope. MIRAC-5 is a novel ground-based instrument that utilizes a state-of-the-art GeoSnap (2 - 13 microns) HgCdTe detector with adaptive optics support from MAPS to study protoplanetary disks, wide-orbit brown dwarfs, planetary companions in the contrast-limit, and a wide range of other astrophysical objects. We have used MIRAC-5 on six engineering observing runs, improving its performance and defining operating procedures. We characterize key aspects of MIRAC-5's performance, including verification that the total telescope, atmosphere, instrument, and detector throughput is approximately 10%. Following a planned dichroic upgrade, the system will have a throughput of 20% and background limiting magnitudes (for SNR = 5 and 8 hour exposure times) of 18.0, 15.6, and 12.6 for the L', M', and N' filters, respectively. The detector pixels experience 1/f noise but, if the astrophysical scene is properly modulated via chopping and nodding sequences, it is less than 10% the Poisson noise from the observed background in an 85 Hz frame. We achieve close to diffraction-limited performance in the N-band and all bands are expected to reach diffraction-limited performance following the adaptive optics system commissioning. We also present an exposure time calculator calibrated to the on-sky results. In its current state, MIRAC-5 will be capable of achieving several scientific objectives including the observation of warm wide-orbit companions. Once the adaptive optics is commissioned and a coronagraph installed in 2025, MIRAC-5 will have contrast-limited performance comparable to JWST, opening new and complementary science investigations for close-in companions.

astro-ph.IM↗

arXiv2024

Resolving the Young 2 Cygni Run-away Star into a Binary using iLocater

Precision radial velocity (RV) spectrographs that use adaptive optics (AO) show promise to advance telescope observing capabilities beyond those of seeing-limited designs. We are building a spectrograph for the Large Binocular Telescope (LBT) named iLocater that uses AO to inject starlight directly into single mode fibers (SMF). iLocater's first acquisition camera system (the `SX' camera), which receives light from one of the 8.4m diameter primary mirrors of the LBT, was initially installed in summer 2019 and has since been used for several commissioning runs. We present results from first-light observations that include on-sky measurements as part of commissioning activities. Imaging measurements of the bright B3IV star 2 Cygni ($V=4.98$) resulted in the direct detection of a candidate companion star at an angular separation of only $\theta = 70$ mas. Follow-up AO measurements using Keck/NIRC2 recover the candidate companion in multiple filters. An $R\approx1500$ miniature spectrograph recently installed at the LBT named ``Lili'' provides spatially resolved spectra of each binary component, indicating similar spectral types and strengthening the case for companionship. Studying the multiplicity of young runaway star systems like 2 Cygni ($36.6 \pm 0.5$ Myr) can help to understand formation mechanisms for stars that exhibit anomalous velocities through the galaxy. This on-sky demonstration illustrates the spatial resolution of the iLocater SX acquisition camera working in tandem with the LBT AO system; it further derisks a number of technical hurdles involved in combining AO with Doppler spectroscopy.

astro-ph.IM↗

arXiv2024

Tuning the MAPS Adaptive Secondary Mirror: Actuator Control, PID Tuning, Power Spectra and Failure Diagnosis

The MMT Adaptive optics exoPlanet characterization System (MAPS) is currently in its engineering phase, operating on-sky at the MMT Telescope on Mt. Hopkins in southern Arizona. The MAPS Adaptive Secondary Mirror's actuators are controlled by a closed loop modified PID control law and an open loop feed-forward law, which in combination allows for faster actuator response time. An essential element of achieving the secondary's performance goals involves the process of PID gain tuning. To start, we briefly discuss the design of the MAPS ASM and its actuators. We then describe the actuator positional control system and control law. Next, we discuss a few of the issues that make ASM tuning difficult. We then outline our initial attempts at tuning the actuator controllers and discuss the use of actuator positional power spectra for both tuning and determining the health and failure states of individual actuators. We conclude by presenting the results of our latest round of tuning configuration trials, which have been successful at decreasing mirror latency, increasing operational mirror modes and improving image PSF.

astro-ph.IM↗

arXiv2024

Design and Test of Small Mirror Supports for Harsh Environments

As wavefront quality demands tighten on space systems for applications such as astronomy and laser communication, mounting small optics such that the wavefront is undisturbed, positioning is adjustable and the design is producible, while surviving harsh space environments, is a continuing challenge. We designed multiple candidate flexure mounts to support small optics (up to 50 mm diameter, and over 100 grams) to survive the qualification and acceptance tests of small spacecraft and units as defined in ISO 19683 and a mounting structure which is adjustable in decenter [+/-0.5mm], tip/tilt +/-0.5deg, and piston [+/-0.25mm]. We will present design details along with measurements showing less than approximately lambda/10 wavefront contribution from the optic bonding process, along with thermal and multi-axis vibration test data showing the mounted optics survived the acceptance testing loads and are suitable for operation in a wide range of harsh environments.

astro-ph.IM↗

arXiv2024

ESCAPE: Efficient Synthesis of Calibrations for Adaptive optics through Pseudo-synthetic and Empirical methods

With the commissioning of the refurbished adaptive secondary mirror (ASM) for the 6.5-meter MMT Observatory under way, special consideration had to be made to properly calibrate the mirror response functions to generate an interaction matrix (IM). The commissioning of the ASM is part of the MMT Adaptive optics exoPlanet characterization System (MAPS) upgrade the observatory's legacy adaptive optics (AO) system. Unlike most AO systems, MAPS employs a convex ASM which prevents the introduction of a calibration source capable of simultaneously illuminating its ASM and wavefront sensor (WFS). This makes calibration of the AO system a significant hurdle in commissioning. To address this, we have employed a hybrid calibration strategy we call the Efficient Synthesis of Calibrations for Adaptive Optics through Pseudo-synthetic and Empirical methods (ESCAPE). ESCAPE combines the DO-CRIME on-sky calibration method with the SPRINT method for computing pseudo-synthetic calibration matrices. To monitor quasi-static system change, the ESCAPE methodology rapidly and continuously generates pseudo-synthetic calibration matrices using continual empirical feedback in either open or closed-loop. In addition, by measuring the current IM in the background while in close-loop, we are also able to measure the optical gains for pyramid wavefront sensor (PyWFS) systems. In this paper, we will provide the mathematical foundation of the ESCAPE calibration strategy and on-sky results from its application in calibrating the MMT Observatory's ASM. Additionally, we will showcase the validation of our approach from our AO testbed and share preliminary on-sky results from MMT.

astro-ph.IM↗

arXiv2023

SOUL at LBT: commissioning results, science and future

The SOUL systems at the Large Bincoular Telescope can be seen such as precursor for the ELT SCAO systems, combining together key technologies such as EMCCD, Pyramid WFS and adaptive telescopes. After the first light of the first upgraded system on September 2018, going through COVID and technical stops, we now have all the 4 systems working on-sky. Here, we report about some key control improvements and the system performance characterized during the commissioning. The upgrade allows us to correct more modes (500) in the bright end and increases the sky coverage providing SR(K)>20% with reference stars G$_{RP}$<17, opening to extragalcatic targets with NGS systems. Finally, we review the first astrophysical results, looking forward to the next generation instruments (SHARK-NIR, SHARK-Vis and iLocater), to be fed by the SOUL AO correction.

astro-ph.IM↗

arXiv2023

The MAPS Adaptive Secondary Mirror: First Light, Laboratory Work, and Achievements

The MMT Adaptive Optics exoPlanet Characterization System (MAPS) is a comprehensive update to the first generation MMT adaptive optics system (MMTAO), designed to produce a facility class suite of instruments whose purpose is to image nearby exoplanets. The system's adaptive secondary mirror (ASM), although comprised in part of legacy components from the MMTAO ASM, represents a major leap forward in engineering, structure and function. The subject of this paper is the design, operation, achievements and technical issues of the MAPS adaptive secondary mirror. We discuss laboratory preparation for on-sky engineering runs, the results of those runs and the issues we discovered, what we learned about those issues in a follow-up period of laboratory work, and the steps we are taking to mitigate them.

astro-ph.IM↗

arXiv2022

A Near-Infrared Pyramid Wavefront Sensor for the MMT

The MMTO Adaptive optics exoPlanet characterization System (MAPS) is an ongoing upgrade to the 6.5-meter MMT Observatory on Mount Hopkins in Arizona. MAPS includes an upgraded adaptive secondary mirror (ASM), upgrades to the ARIES spectrograph, and a new AO system containing both an optical and near-infrared (NIR; 0.9-1.8 um) pyramid wavefront sensor (PyWFS). The NIR PyWFS will utilize an IR-optimized double pyramid coupled with a SAPHIRA detector: a low-read noise electron Avalanche Photodiode (eAPD) array. This NIR PyWFS will improve MAPS's sky coverage by an order of magnitude by allowing redder guide stars (e.g. K & M-dwarfs or highly obscured stars in the Galactic plane) to be used. To date, the custom designed cryogenic SAPHIRA camera has been fully characterized and can reach sub-electron read noise at high avalanche gain. In order to test the performance of the camera in a closed-loop environment prior to delivery to the observatory, an AO testbed was designed and constructed. In addition to testing the SAPHIRA's performance, the testbed will be used to test and further develop the proposed on-sky calibration procedure for MMTO's ASM. We will report on the anticipated performance improvements from our NIR PyWFS, the SAPHIRA's closed-loop performance on our testbed, and the status of our ASM calibration procedure.

astro-ph.IM↗

arXiv2020

Design and development of a high-speed Visible Pyramid Wavefront Sensor for the MMT AO system

MAPS, MMT Adaptive optics exoPlanet characterization System, is the upgrade of legacy 6.5m MMT adaptive optics system. It is an NSF MSIP-funded project that includes (i) refurbishing of the MMT Adaptive Secondary Mirror (ASM), (ii) new high sensitive and high spatial order visible and near-infrared pyramid wavefront sensors, and (iii) the upgrade of Arizona Infrared Imager and Echelle Spectrograph (ARIES) and MMT high Precision Imaging Polarimeter (MMTPol) science cameras. This paper will present the design and development of the visible pyramid wavefront sensor. This system consists of an acquisition camera, a fast-steering tip-tilt modulation mirror, a double pyramid, a pupil imaging triplet lens, and a low noise and high-speed frame rate based CCID75 camera. We will report on hardware and software and present the laboratory characterization results of the individual subsystems, and outline the on-sky commissioning plan.

astro-ph.IM↗

arXiv2020

Final Design and On-Sky Testing of the iLocater SX Acquisition Camera: Broadband Single-Mode Fiber Coupling

Enabling efficient injection of light into single-mode fibers (SMFs) is a key requirement in realizing diffraction-limited astronomical spectroscopy on ground-based telescopes. SMF-fed spectrographs, facilitated by the use of adaptive optics (AO), offer distinct advantages over comparable seeing-limited designs, including higher spectral resolution within a compact and stable instrument volume, and a telescope independent spectrograph design. iLocater is an extremely precise radial velocity (EPRV) spectrograph being built for the Large Binocular Telescope (LBT). We have designed and built the front-end fiber injection system, or acquisition camera, for the SX (left) primary mirror of the LBT. The instrument was installed in 2019 and underwent on-sky commissioning and performance assessment. In this paper, we present the instrument requirements, acquisition camera design, as well as results from first-light measurements. Broadband single-mode fiber coupling in excess of 35% (absolute) in the near-infrared (0.97-1.31μm) was achieved across a range of target magnitudes, spectral types, and observing conditions. Successful demonstration of on-sky performance represents both a major milestone in the development of iLocater and in making efficient ground-based SMF-fed astronomical instruments a reality.

astro-ph.IM↗

arXiv2018

SHARK-NIR, the coronagraphic camera for LBT, moving toward construction

SHARK-NIR is one of the two coronagraphic instruments proposed for the Large Binocular Telescope. Together with SHARK-VIS (performing coronagraphic imaging in the visible domain), it will offer the possibility to do binocular observations combining direct imaging, coronagraphic imaging and coronagraphic low resolution spectroscopy in a wide wavelength domain, going from 0.5μm to 1.7μm. Additionally, the contemporary usage of LMIRCam, the coronagraphic LBTI NIR camera, working from K to L band, will extend even more the covered wavelength range. In January 2017 SHARK-NIR underwent a successful final design review, which endorsed the instrument for construction and future implementation at LBT. We report here the final design of the instrument, which foresees two intermediate pupil planes and three focal planes to accomodate a certain number of coronagraphic techniques, selected to maximize the instrument contrast at various distances from the star. Exo-Planets search and characterization has been the science case driving the instrument design, but the SOUL upgrade of the LBT AO will increase the instrument performance in the faint end regime, allowing to do galactic (jets and disks) and extra-galactic (AGN and QSO) science on a relatively wide sample of targets, normally not reachable in other similar facilities.

astro-ph.IM↗

arXiv2015

First Light with ALES: A 2-5 Micron Adaptive Optics Integral Field Spectrograph for the LBT

Integral field spectrographs are an important technology for exoplanet imaging, due to their ability to take spectra in a high-contrast environment, and improve planet detection sensitivity through spectral differential imaging. ALES is the first integral field spectrograph capable of imaging exoplanets from 3-5$μ$m, and will extend our ability to characterize self-luminous exoplanets into a wavelength range where they peak in brightness. ALES is installed inside LBTI/LMIRcam on the Large Binocular Telescope, taking advantage of existing AO systems, camera optics, and a HAWAII-2RG detector. The new optics that comprise ALES are a Keplerian magnifier, a silicon lenslet array with diffraction suppressing pinholes, a direct vision prism, and calibration optics. All of these components are installed in filter wheels making ALES a completely modular design. ALES saw first light at the LBT in June 2015.

astro-ph.IM↗

arXiv2003

High Resolution Images of Orbital Motion in the Trapezium Cluster: First Scientific Results from the MMT Deformable Secondary Mirror Adaptive Optics System

We present the first scientific images obtained with a deformable secondary mirror adaptive optics system. We utilized the 6.5m MMT AO system to produce high-resolution (FWHM=0.07'') near infrared (1.6 um) images of the young (~1 Myr) Orion Trapezium theta 1 Ori cluster members. A combination of high spatial resolution and high signal to noise allowed the positions of these stars to be measured to within ~0.003'' accuracies. Including previous speckle data (Weigelt et al. 1999), we analyze a six year baseline of high-resolution observations of this cluster. Over this baseline we are sensitive to relative proper motions of only ~0.002''/yr (4.2 km/s at 450 pc). At such sensitivities we detect orbital motion in the very tight theta 1 Ori B2B3 (52 AU separation) and theta 1 Ori A1A2 (94 AU separation) systems. Such motions are consistent with those independently observed by Schertl et al. (2003) with speckle interferometry, giving us confidence that these very small (~0.002''/yr) orbital motions are real. All five members of the theta 1 Ori B system appear likely gravitationally bound. The very lowest mass member of the theta 1 Ori B system (B4) has K' ~11.66 and an estimated mass of ~0.2 Msun. There was very little motion (4+/-15 km/s) detected of B4 w.r.t B1 or B2, hence B4 is possibly part of the theta 1 Ori B group. We suspect that if this very low mass member is physically associated it most likely is in an unstable (non-hierarchical) orbital position and will soon be ejected from the group. The theta 1 Ori B system appears to be a good example of a star formation ``mini-cluster'' which may eject the lowest mass members of the cluster in the near future. This ``ejection'' process could play a major role in the formation of low mass stars and brown dwarfs.

astro-ph↗