arXiv subjects

Massimo Gervasi

Publications and source records attributed to Massimo Gervasi.

At least 19 recordsLinked to original sources

arXiv2026

Flux jump correction in the QUBIC TES data pipeline

Flux jumps occur in the readout electronics of Transition Edge Sensor (TES) detectors coupled to Superconducting Quantum Interference Devices (SQUIDs), as a consequence of the periodic transfer function of SQUIDs in the superconducting regime. These events manifest as discontinuities in the Time Ordered Data (TOD) and can significantly degrade the quality of the measured signals. In this work, we present an automated pipeline to identify and correct flux jumps in the calibration data of the QUBIC (Q \& U Bolometric Interferometer for Cosmology) instrument, designed to measure the B-mode polarization of the Cosmic Microwave Background (CMB). Using data from multiple observation campaigns, we characterize the statistical properties of flux jumps and compare them with expectations based on the electronic configuration of the instrument. The proposed pipeline successfully corrects these events, allowing the recovery of affected data and enabling their use in subsequent CMB analysis.

astro-ph.IM↗

arXiv2025

On beam characterization of ground-based CMB radio telescopes using UAV-mounted sources: application to the QUIJOTE TFGI and plans for LSPE-Strip

The Large Scale Polarization Explorer (LSPE) project, funded by the Italian Space Agency (ASI), includes the development of LSPE-Strip, a ground-based radio telescope for observing Cosmic Microwave Background (CMB) anisotropies. LSPE-Strip, nearing its construction phase, will operate from the Teide Observatory in Tenerife, employing 49 coherent polarimeters at 43 GHz to deliver critical data on CMB anisotropies and 6 channels at 95 GHz as atmospheric monitor. On-site characterization of such advanced instruments is crucial to detect possible systematic effects, such as gain fluctuations, beam distortions, and pointing errors, that can compromise performance by introducing spurious polarizations or radiation collection from unintended directions. To address these challenges, a drone-mounted Q-band test source for on-site characterization of LSPE-Strip's polarimeter array was developed. Modern Unmanned Aerial Vehicles (UAVs) offer a flexible approach for antenna pattern measurements, yet their use in high-frequency radio astronomy is not consolidated practice. In October 2022, a UAV-based measurement campaign was conducted with the TFGI instrument on the second QUIJOTE telescope in Tenerife, in collaboration with the Instituto de Astrofisica de Canarias. This pioneering effort aimed to validate UAV-based beam characterization methods and assess QUIJOTE's performance under operational conditions. Preliminary results demonstrated high measurement accuracy, leveraging QUIJOTE's dual-receiver configuration for beam validation. These findings provide valuable insights for optimizing UAV systems in preparation for LSPE-Strip's future characterization.

astro-ph.IM↗

arXiv2025

COSMICA: a novel parallel GPU code for Cosmic Rays propagation in heliosphere

The complex structure of interplanetary magnetic fields and their variability, due to solar activity, make it necessary to compute the Cosmic Ray (CR) modulation with numerical simulations. COde for a Speedy Monte Carlo (MC) Involving Cuda Architecture (COSMICA) is a MC code, solving backward-in-time the system of Stochastic Differential Equations (SDE) equivalent to the Parker Transport Equation (PTE). The Graphics Processing Unit (GPU) parallelization of COSMICA code is a game changer in this field because it reduces the computational time of a standard simulation from the order of hundred of minutes to few of them. Furthermore, the code is capable of distributing the computations on clusters of machines with multiple GPUs, opening the way for scaling. In COSMICA we implemented the synchronous broadcasting of memory access for evolving variable samples, the rounding of virtual particle set numbers, to fulfil the GPU blocks, and the exploitation of shared memory to free registers. Furthermore, we compactify the mathematical computations and pass to the lighter momentum formulation of SDE. The first porting of the code on GPU architecture brings it to a speed-up of 40X. The successful optimizations bring 1.5X speed-up.

physics.comp-ph↗

arXiv2025

The LSPE-Strip Pointing Reconstruction and Star Tracker

This paper aims to describe the Pointing Reconstruction Model (PRM) and the prototype Star Tracker, which will be mounted on LSPE-Strip, a microwave Q- and W-band CMB telescope planned for installation at the "Observatorio del Teide" in Tenerife. The PRM integrates information on the instantaneous attitude provided by the telescope control system to determine the actual pointing direction and focal plane orientation of the telescope. It accounts for various non-idealities in the telescope setup, represented by eight configuration angles, which will be calibrated using the Star Tracker. Following the derivation of the PRM formalism and its implementation, we investigate the pointing errors caused by incorrect calibration of these configuration angles to validate the required 1 arcminute maximum systematic pointing error for the LSPE-Strip survey. This paper also describes the main structure and operations of the Star Tracker and presents the results of a campaign of actual sky observations conducted with a prototype. The results demonstrate a Star Tracker RMS accuracy of approximately 3 arcseconds, while systematic errors remain below 10 arcseconds. Based on these results, we analyzed the problem of reconstructing the PRM configuration angles. Two methods for intercalibrating the Star Tracker's pointing direction with respect to the focal plane's pointing direction were examined: (1) observations of planets and (2) observations of a drone carrying both an optical beacon and a radio beacon. In the first case, an intercalibration accuracy between 1/3 arcminute and 1 arcminute is achievable. In the second case, the expected intercalibration accuracy ranges from 0.25 arcminute to 1 arcminute.

astro-ph.IM↗

arXiv2020

A chemically etched corrugated feedhorn array for D-band CMB observations

We present the design, manufacturing, and testing of a 37-element array of corrugated feedhorns for Cosmic Microwave Background (CMB) measurements between $140$ and $170$ GHz. The array was designed to be coupled to Kinetic Inductance Detector arrays, either directly (for total power measurements) or through an orthomode transducer (for polarization measurements). We manufactured the array in platelets by chemically etching aluminum plates of $0.3$ mm and $0.4$ mm thickness. The process is fast, low-cost, scalable, and yields high-performance antennas compared to other techniques in the same frequency range. Room temperature electromagnetic measurements show excellent repeatability with an average cross polarization level about $-20$ dB, return loss about $-25$ dB, first sidelobes below $-25$ dB and far sidelobes below $-35$ dB. Our results qualify this process as a valid candidate for state-of-the-art CMB experiments, where large detector arrays with high sensitivity and polarization purity are of paramount importance in the quest for the discovery of CMB polarization $B$-modes.

astro-ph.IM↗

arXiv2019

NIEL Dose Analysis on triple and single junction InGaP/GaAs/Ge solar cells irradiated with electrons, protons and neutrons

Triple junction (InGaP/GaAs/Ge) and single junction (SJ) solar cells were irradiated with electrons, protons and neutrons. The degradation of remaining factors was analyzed as function of the induced Displacement Damage Dose (DDD) calculated by means of the SR-NIEL (Screened Relativistic Non Ionizing\ Energy Loss) approach. In particular, the aim of this work is to analyze the variation of the solar cells remaining factors due to neutron irradiation with respect to those previously obtained with electrons and protons. The current analysis confirms that the degradation of the $P_{max}$ electrical parameter is related by means of the usual semi-empirical expression to the displacement dose, independently of type of the incoming particle. $I_{sc}$ and $V_{oc}$ parameters were also measured as a function of the displacement damage dose. Furthermore, a DLTS analysis was carried out on diodes - with the same epitaxial structure as the middle sub-cell - irradiated with neutrons.

physics.ins-det↗

arXiv2019

The HelMod Model in the Works for Inner and Outer Heliosphere: from AMS to Voyager Probes Observations

HelMod is a Monte Carlo code developed to describe the transport of Galactic Cosmic Rays (GCRs) through the heliosphere from the interstellar space to the Earth. In the current HelMod version 4 the modulation process, based on Parker's equation, is applied to the propagation of GCRs in the inner and outer heliosphere, i.e., including the heliosheath. HelMod was proved to reproduce protons, nuclei and electrons cosmic rays spectra observed during solar cycles 23-24 by several detectors, for instance, PAMELA, BESS and AMS-02. In particular, the unprecedented accuracy of AMS-02 observations allowed one a better tuning of the description regarding the solar modulation mechanisms implemented in HelMod. In addition, HelMod demonstrated to be capable of reproducing the uxes observed by the Voyager probes in the inner and outer regions of heliosphere up to its border.

physics.space-ph↗

arXiv2019

QUBIC: Exploring the primordial Universe with the Q\&U Bolometric Interferometer

In this paper we describe QUBIC, an experiment that will observe the polarized microwave sky with a novel approach, which combines the sensitivity of state-of-the art bolometric detectors with the systematic effects control typical of interferometers. QUBIC unique features are the so-called "self-calibration", a technique that allows us to clean the measured data from instrumental effects, and its spectral imaging power, i.e. the ability to separate the signal in various sub-bands within each frequency band. QUBIC will observe the sky in two main frequency bands: 150 GHz and 220 GHz. A technological demonstrator is currently under testing and will be deployed in Argentina during 2019, while the final instrument is expected to be installed during 2020.

astro-ph.IM↗

arXiv2018

NIEL DOSE and DLTS Analyses on Triple and Single Junction solar cells irradiated with electrons and protons

Space solar cell radiation hardness is of fundamental importance in view of the future missions towards harsh radiation environment (like the Jupiter missions) and for the new spacecraft using Electrical Propulsion. In this paper we report the radiation data for triple junction (TJ) solar cells and related component cells. Triple junction solar cells, InGaP top cells and GaAs middle cells degrade after electron radiation as expected. With proton irradiation, a high spread in the remaining factors was observed, especially for the TJ and Ge bottom cells. Radiation results have been analyzed by means of the Displacement Damage Dose method and DLTS spectroscopy. In particular with DLTS spectroscopy it was possible to analyze the nature of a few defects introduced by irradiation inside the GaAs sub cell observing a strong correlation with the Displacement Damage Dose.

physics.ins-det↗

arXiv2018

Effects of irradiation on Triple and Single Junction InGaP/GaAs/Ge solar cells

The investigation of the degradation effects on triple-junction (TJ) solar cells, operating in space environment, is of primary importance in view of future space missions towards harsh radiation orbits (e.g. MEO with high particle irradiation intensity) and for the new spacecraft based on electrical propulsion. In the present work, we report the experimental results obtained from the irradiation test campaign carried out both on (InGaP/GaAs/Ge) TJ solar cells and on single junction (SJ) isotype sub-cells (i.e. InGaP top cells, GaAs middle cells and Ge bottom cells). In particular, the electrical performances degradation of the irradiated samples was analyzed by means of the Displacement Damage Dose (DDD) method based on the NIEL (Non Ionizing Energy Loss) scaling hypothesis, with DDD doses computed by the SR-NIEL approach. By plotting the remaining factors as a function of the DDD, a single degradation curve for each sample type and for each electrical parameter has been found. The collapse of the remaining factors on a single curve has been achieved by selecting suitable displacement threshold energies, $E_d$, for NIEL calculation. Moreover, DLTS (Deep level Transient Spectroscopy) technique was used to better understand the nature of the defects produced by irradiation. DLTS measurements reveal a good correlation between defects introduced by irradiation inside the GaAs sub-cell and the calculated Displacement Damage Doses.

physics.ins-det↗

arXiv2017

Forecast analysis and focal plane optimization for a multi-frequency CMB B-modes polarization experiment: the case of LSPE

We present an optimization scheme for the focal plane of a multi-frequency CMB B-modes experiment with a fixed number of detectors and apply it to the specific case of LSPE experiment. Optimal focal planes are identified on the ground of different figures of merit defined in terms of the forecasted uncertainty $σ_r$ on the tensor--to-scalar ratio $r$ and the expected map variance from foreground and instrumental noise residuals. We then perform a forecast analysis in order to assess the precision achievable in B-modes measurements.

astro-ph.CO↗

arXiv2017

The HelMod Monte Carlo Model for the Propagation of Cosmic Rays in Heliosphere

The heliospheric modulation model HelMod solve the transport-equation for the Galactic Cosmic Rays propagation through the heliosphere down to Earth. It is based on a 2-D Monte Carlo approach, that includes a general description of the symmetric and antisymmetric parts of the diffusion tensor, thus, properly treating the particle drift effects as well as convection within the solar wind and adiabatic energy loss. The model was tuned in order to fit 1) the data observed outside the ecliptic plane at several distances from the Earth and 2) the spectra observed near the Earth for both, high and low solar activity periods. Great importance was given to description of polar regions of the heliosphere. We present the flux for protons, antiprotons and helium nuclei computed along the solar cycle 23-24 in comparison with experimental observations and prediction for the full solar cycle 24.

astro-ph.HE↗

arXiv2017

Displacement Damage dose and DLTS Analyses on Triple and Single Junction solar cells irradiated with electrons and protons

Space solar cells radiation hardness is of fundamental importance in view of the future missions towards harsh radiation environment (like e.g. missions to Jupiter) and for the new spacecraft using electrical propulsion. In this paper we report the radiation data for triple junction (TJ) solar cells and related component cells. Triple junction solar cells, InGaP top cells and GaAs middle cells degrade after electron radiation as expected. With proton irradiation, a high spread in the remaining factors was observed, especially for the TJ and bottom cells. Very surprising was the germanium bottom junction that showed very high degradation after protons whereas it is quite stable against electrons. Radiation results have been analyzed by means of the Displacement Damage Dose method and DLTS spectroscopy.

physics.ins-det↗

arXiv2014

Efficient Differential Fourier-Transform Spectrometer for precision Sunyaev-Zel'dovich effect measurements

Precision measurements of the Sunyaev-Zel'dovich effect in clusters of galaxies require excellent rejection of common-mode signals and wide frequency coverage. We describe an imaging, efficient, differential Fourier transform spectrometer (FTS), optimized for measurements of faint brightness gradients at millimeter wavelengths. Our instrument is based on a Martin-Puplett interferometer (MPI) configuration. We combined two MPIs working synchronously to use the whole input power. In our implementation the observed sky field is divided into two halves along the meridian, and each half-field corresponds to one of the two input ports of the MPI. In this way, each detector in the FTS focal planes measures the difference in brightness between two sky pixels, symmetrically located with respect to the meridian. Exploiting the high common-mode rejection of the MPI, we can measure low sky brightness gradients over a high isotropic background. The instrument works in the range $\sim$ 1$-$20 cm$^{-1}$ (30$-$600 GHz), has a maximum spectral resolution $1/(2 \ OPD) = 0.063 \ cm^{-1}$ (1.9 GHz), and an unvignetted throughput of 2.3 cm$^2$sr. It occupies a volume of 0.7$\times$0.7$\times$0.33 m$^3$ and has a weight of 70 kg. This design can be implemented as a cryogenic unit to be used in space, as well as a room-temperature unit working at the focus of suborbital and ground-based mm-wave telescopes. The first in-flight test of the instrument is with the OLIMPO experiment on a stratospheric balloon; a larger implementation is being prepared for the Sardinia radio telescope.

astro-ph.IM↗

arXiv2012

A template of atmospheric molecular oxygen circularly polarized emission for CMB experiments

We compute the polarized signal from atmospheric molecular oxygen due to Zeeman effect in the Earth magnetic field for various sites suitable for CMB measurements such as South Pole, Dome C (Antarctica) and Atacama desert (Chile). We present maps of this signal for those sites and show their typical elevation and azimuth dependencies. We find a typical circularly polarized signal (V Stokes parameter) level of 50 - 300 μK at 90 GHz when looking at the zenith; Atacama site shows the lowest emission while Dome C site presents the lowest gradient in polarized brightness temperature (0.3 μK/deg at 90 GHz). The accuracy and robustness of the template are tested with respect to actual knowledge of the Earth magnetic field, its variability and atmospheric parameters.

astro-ph.CO↗

arXiv2011

W-band prototype of platelet feed-horn array for CMB polarisation measurements

We present the design and performance of a 2x2 prototype array of corrugated feed-horns in W-band. The module is fabricated using a so-called "platelet" technique by milling Aluminum plates. This technique is suitable for low-cost and scalable high performance applications. Room temperature Return Loss measurements show a low (<-30 dB) reflection over a 30% bandwidth with a maximum matching of -42 dB at 100 GHz for all four antennas. Beam pattern measurements indicate good repeatability and a low (-25 dB) sidelobe and crosspolarisation levels. This work is particularly relevant for future Cosmic Microwave Background polarisation measurements, which require large microwave cryogenic detector arrays coupled to high performance corrugated feed horns.

astro-ph.IM↗

arXiv2011

A template of atmospheric O2 circularly polarized emission for CMB experiments

We compute the circularly polarized signal from atmospheric molecular oxygen. Polarization of O2 rotational lines is caused by Zeeman effect in the Earth magnetic field. We evaluate the circularly polarized emission for various sites suitable for CMB measurements: South Pole and Dome C (Antarctica), Atacama (Chile) and Testa Grigia (Italy). An analysis of the polarized signal is presented and discussed in the framework of future CMB polarization experiments. We find a typical circularly polarized signal (V Stokes parameter) of ~ 50 - 300 μK at 90 GHz looking at the zenith. Among the other sites Atacama shows the lower polarized signal at the zenith. We present maps of this signal for the various sites and show typical elevation and azimuth scans. We find that Dome C presents the lowest gradient in polarized temperature: ~ 0.3 μK/\circ at 90 GHz. We also study the frequency bands of observation: around ν \simeq 100 GHz and ν \simeq 160 GHz we find the best conditions because the polarized signal vanishes. Finally we evaluate the accuracy of the templates and the signal variability in relation with the knowledge and the variability of the Earth magnetic field and the atmospheric parameters.

astro-ph.IM↗

arXiv2010

On the detectability of cosmic ray electron spectral features in the microwave/mm-wave range

Recent measurements of cosmic ray electron energy spectra suggest that above 10 GeV there may be deviations from a single power law spectrum. There are hints (ATIC) for a bump occurring between 100 GeV and 1TeV, meaning that there might be more high energy electrons than expected. Whether these electrons are produced within pulsar magnetospheres, or due to Dark Matter annihilation or decay, this is still matter of debate. Understanding the nature of these ultra high energy particles is a difficult task that can be fulfilled using all the available astrophysical observables. We investigate how different energy spectra produce different observable manifestations in the radio/microwave/mm-wave domain, where corresponding deviations from a synchrotron power law could appear. We raise the question around the detectability of these possible radio spectral features, which may be interesting for a wide scientific community including astrophysicists and scientists working on foregrounds removal for CMB experiments.

astro-ph.HE↗