arXiv subjects

Mathias Hoppe

Publications and source records attributed to Mathias Hoppe.

12 recordsLinked to original sources

arXiv2024

Reduced kinetic modelling of shattered pellet injection in ASDEX Upgrade

Plasma-terminating disruptions represent a critical outstanding issue for reactor-relevant tokamaks. ITER will use shattered pellet injection (SPI) as its disruption mitigation system to reduce heat loads, vessel forces, and to suppress the formation of runaway electrons. In this paper we demonstrate that reduced kinetic modelling of SPI is capable of capturing the major experimental trends in ASDEX Upgrade SPI experiments, such as dependence of the radiated energy fraction on neon content, or the current quench dynamics. Simulations are also consistent with the experimental observation of no runaway electron generation with neon and mixed deuterium-neon pellet composition. We also show that statistical variations in the fragmentation process only have a notable impact on disruption dynamics at intermediate neon doping, as was observed in experiments.

physics.plasm-ph↗

arXiv2024

Reduced modeling of scrape-off losses of runaway electrons during tokamak disruptions

Accurate modeling of runaway electron generation and losses during tokamak disruptions is crucial for the development of reactor-scale tokamak devices. In this paper we present a reduced model for runaway electron losses due to flux surface scrape-off caused by the vertical motion of the plasma. The model is made compatible with computationally inexpensive one-dimensional models averaging over a fixed flux-surface geometry, by formulating it as a loss term outside an estimated time-varying minor radius of the last closed flux surface. We then implement this model in the disruption modeling tool DREAM, and demonstrate its impact on selected scenarios relevant for ITER. Our results indicate that scrape-off losses may be crucial for making complete runaway avoidance possible even in a $15\,\rm MA$ DT H-mode ITER scenario. The results are however sensitive to the details of the runaway electron generation and phenomena affecting the current density profile, such as the current profile relaxation at the beginning of the disruption.

physics.plasm-ph↗

arXiv2024

Fluid and kinetic studies of tokamak disruptions using Bayesian optimization

When simulating runaway electron dynamics in tokamak disruptions, fluid models with lower numerical cost are often preferred to more accurate kinetic models. The aim of this work is to compare fluid and kinetic simulations of a large variety of different disruption scenarios in ITER. We consider both non-activated and activated scenarios; for the latter we derive and implement kinetic sources for the Compton scattering and tritium beta decay runaway electron generation mechanisms in our simulation tool DREAM [M. Hoppe et al 2021 Comp. Phys. Commun. 268, 108098]. To achieve a diverse set of disruption scenarios, Bayesian optimization is used to explore a range of massive material injection densities for deuterium and neon. The cost function is designed to distinguish between successful and unsuccessful disruption mitigation based on the runaway current, current quench time and transported fraction of the heat loss. In the non-activated scenarios, we find that fluid and kinetic disruption simulations can have significantly different runaway electron dynamics, due to an overestimation of the runaway seed by the fluid model. The primary cause of this is that the fluid hot-tail generation model neglects superthermal electron transport losses during the thermal quench. In the activated scenarios, the fluid and kinetic models give similar predictions, which can be explained by the significant influence of the activated sources on the RE dynamics and the seed.

physics.plasm-ph↗

arXiv2024

Runaway Electron Dynamics in ITER Disruptions with Shattered Pellet Injections

This study systematically explores the parameter space of disruption mitigation through shattered pellet injection in ITER with a focus on runaway electron dynamics, using the disruption modelling tool DREAM. The physics fidelity is considerably increased compared to previous studies, by e.g., using realistic magnetic geometry, resistive wall configuration, thermal quench onset criteria, as well as including additional effects, such as ion transport and enhanced runaway electron transport during the thermal quench. The work aims to provide a fairly comprehensive coverage of experimentally feasible scenarios, considering plasmas representative of both non-activated and high-performance DT operation, different thermal quench onset criteria and transport levels, a wide range of hydrogen and neon quantities injected in one or two stages, and pellets with various characteristic shard sizes. Using a staggered injection scheme, with a pure hydrogen injection preceding a mixed hydrogen-neon injection, we find injection parameters leading to acceptable runaway electron currents in all investigated discharges without activated runaway sources. Dividing the injection into two stages is found to significantly enhance the assimilation and minimize runaway electron generation due to the hot-tail mechanism. However, while a staggered injection outperforms a single stage injection also in cases with radioactive runaway electron sources, no cases with acceptable runaway electron currents are found for a DT-plasma with a 15 MA plasma current.

physics.plasm-ph↗

arXiv2023

Bayesian optimization of massive material injection for disruption mitigation in tokamaks

A Bayesian optimization framework is used to investigate scenarios for disruptions mitigated with combined deuterium and neon injection in ITER. The optimization cost function takes into account limits on the maximum runaway current, the transported fraction of the heat loss and the current quench time. The aim is to explore the dependence of the cost function on injected densities, and provide insights into the behaviour of the disruption dynamics for representative scenarios. The simulations are conducted using the numerical framework DREAM (Disruption Runaway Electron Analysis Model). We show that irrespective of the quantities of the material deposition, multi-megaampere runaway currents will be produced in the deuterium-tritium phase of operations, even in the optimal scenarios. However, the severity of the outcome can be influenced by tailoring the radial profile of the injected material; in particular if the injected neon is deposited at the edge region it leads to a significant reduction of both the final runaway current and the transported heat losses. The Bayesian approach allows us to map the parameter space efficiently, with more accuracy in favorable parameter regions, thereby providing us information about the robustness of the optima.

physics.plasm-ph↗

arXiv2023

Feasibility of the EDICAM camera for runaway electron detection in JT-60SA disruptions

The visible camera system EDICAM (Event Detection Intelligent Camera), recently installed on JT-60SA, is simulated to assess whether it can be used for measuring synchrotron radiation from relativistic runaway electrons. In this simulation, the SOFT synthetic synchrotron diagnostic framework is used to compute the synthetic synchrotron camera images from a JT-60SA-like disruption modelled with the DREAM disruption simulation code. In the studied scenario, a large amount of argon is added to the plasma, and a disruption is simulated by starting a prescribed exponential temperature drop and finishing with further cooling provided by the argon in a self-consistent simulation of the current quench. The background plasma evolution is calculated by DREAM self-consistently with the fast electron population, which is modelled kinetically. The resulting runaway electron distribution function along with the parameters of the EDICAM visible camera system are used as an input to the SOFT framework to assess the feasibility of the camera for runaway electron detection. We find that the runaway electron beam formed in the disruption can produce synchrotron radiation observable by the EDICAM system, thus enabling the use of the EDICAM for the characterization of runaway electron beams.

physics.plasm-ph↗

arXiv2022

Bayesian approach for validation of runaway electron simulations

Plasma-terminating disruptions in future fusion reactors may result in conversion of the initial current to a relativistic runaway electron beam. Validated predictive tools are required to optimize the scenarios and mitigation actuators to avoid the excessive damage that can be caused by such events. Many of the simulation tools applied in fusion energy research require the user to specify several input parameters that are not constrained by the available experimental information. Hence, a typical validation exercise requires multiparameter optimization to calibrate the uncertain input parameters for the best possible representation of the investigated physical system. The conventional approach, where an expert modeler conducts the parameter calibration based on domain knowledge, is prone to lead to an intractable validation challenge. For a typical simulation, conducting exhaustive multiparameter investigations manually to ensure a globally optimal solution and to rigorously quantify the uncertainties is an unattainable task, typically covered only partially and unsystematically. Bayesian inference algorithms offer a promising alternative approach that naturally includes uncertainty quantification and is less subjective to user bias in choosing the input parameters. The main challenge in using these methods is the computational cost of simulating enough samples to construct the posterior distributions for the uncertain input parameters. This challenge can be overcome by combining probabilistic surrogate modelling, such as Gaussian Process regression, with Bayesian optimization, which can reduce the number of required simulations by several orders of magnitude. Here, we implement this type of Bayesian optimization framework for a model for analysis of disruption runaway electrons, and explore for simulations of current quench in a JET plasma discharge with an argon induced disruption.

physics.plasm-ph↗

arXiv2022

Runaway dynamics in disruptions with current relaxation

The safe operation of tokamak reactors requires a reliable modeling capability of disruptions, and in particular the spatio-temporal dynamics of associated runaway electron currents. In a disruption, instabilities can break up magnetic surfaces into chaotic field line regions, causing current profile relaxation, as well as a rapid radial transport of heat and particles. Using a mean-field helicity transport model implemented in the disruption runaway modeling framework DREAM, we calculate the dynamics of runaway electrons in the presence of current relaxation events. In scenarios where flux surfaces remain intact in parts of the plasma, a skin current is induced at the boundary of the intact magnetic field region. This skin current region becomes an important center concerning the subsequent dynamics: It may turn into a hot ohmic current channel, or a sizable radially localized runaway beam, depending on the heat transport. If the intact region is in the plasma edge, runaway generation in the counter-current direction can occur, which may develop into a sizable reverse runaway beam. Even when the current relaxation extends to the entire plasma, the final runaway current density profile can be significantly affected, as the induced electric field is reduced in the core and increased in the edge, thereby shifting the center of runaway generation towards the edge.

physics.plasm-ph↗

arXiv2021

The hot-tail runaway seed landscape during the thermal quench in tokamaks

Runaway electron populations seeded from the hot-tail generated by the rapid cooling in plasma-terminating disruptions are a serious concern for next-step tokamak devices such as ITER. Here, we present a comprehensive treatment of the thermal quench, including the superthermal electron dynamics, heat and particle transport, atomic physics, and radial losses due to magnetic perturbations: processes that are strongly linked and essential for the evaluation of the runaway seed in disruptions mitigated by material injection. We identify limits on the injected impurity density and magnetic perturbation level for which the runaway seed current is acceptable without excessive thermal energy being lost to the wall via particle impact. The consistent modelling of generation and losses shows that runaway beams tend to form near the edge of the plasma, where they could be deconfined via external perturbations.

physics.plasm-ph↗

arXiv2020

Runaway electron modelling in the self-consistent core European Transport Simulator, ETS

Relativistic runaway electrons are a major concern in tokamaks. The European framework for Integrated Modelling (EU-IM), facilitates the integration of different plasma simulation tools by providing a standard data structure for communication that enables relatively easy integration of different physics codes. A three-level modelling approach was adopted for runaway electron simulations within the EU-IM. Recently, a number of runaway electron modelling modules have been integrated into this framework. The first level of modelling (Runaway Indicator) is limited to the indication if runaway electron generation is possible or likely. The second level (Runaway Fluid) adopts an approach similar to e.g. the GO code, using analytical formulas to estimate changes in the runaway electron current density. The third level is based on the solution of the electron kinetics. One such code is LUKE that can handle the toroidicity-induced effects by solving the bounce-averaged Fokker-Planck equation. Another approach is used in NORSE, which features a fully nonlinear collision operator that makes it capable of simulating major changes in the electron distribution, for example slide-away. Both codes handle the effect of radiation on the runaway distribution. These runaway-electron modelling codes are in different stages of integration into the EU-IM infrastructure, and into the European Transport Simulator (ETS), which is a fully capable modular 1.5D core transport simulator. ETS with Runaway Fluid was benchmarked to the GO code implementing similar physics. Coherent integration of kinetic solvers requires more effort on the coupling, especially regarding the definition of the boundary between runaway and thermal populations, and on consistent calculation of resistivity. Some of these issues are discussed.

physics.plasm-ph↗

arXiv2018

Dynamics of positrons during relativistic electron runaway

Sufficiently strong electric fields in plasmas can accelerate charged particles to relativistic energies. In this paper we describe the dynamics of positrons accelerated in such electric fields, and calculate the fraction of created positrons that become runaway accelerated, along with the amount of radiation that they emit. We derive an analytical formula that shows the relative importance of the different positron production processes, and show that above a certain threshold electric field the pair production by photons is lower than that by collisions. We furthermore present analytical and numerical solutions to the positron kinetic equation; these are applied to calculate the fraction of positrons that become accelerated or thermalized, which enters into rate equations that describe the evolution of the density of the slow and fast positron populations. Finally, to indicate operational parameters required for positron detection during runaway in tokamak discharges, we give expressions for the parameter dependencies of detected annihilation radiation compared to bremsstrahlung detected at an angle perpendicular to the direction of runaway acceleration. Using the full leading order pair production cross section, we demonstrate that previous related work has overestimated the collisional pair production by at least a factor of four.

physics.plasm-ph↗

arXiv2017

SOFT: A synthetic synchrotron diagnostic for runaway electrons

Improved understanding of the dynamics of runaway electrons can be obtained by measurement and interpretation of their synchrotron radiation emission. Models for synchrotron radiation emitted by relativistic electrons are well established, but the question of how various geometric effects -- such as magnetic field inhomogeneity and camera placement -- influence the synchrotron measurements and their interpretation remains open. In this paper we address this issue by simulating synchrotron images and spectra using the new synthetic synchrotron diagnostic tool SOFT (Synchrotron-detecting Orbit Following Toolkit). We identify the key parameters influencing the synchrotron radiation spot and present scans in those parameters. Using a runaway electron distribution function obtained by Fokker-Planck simulations for parameters from an Alcator C-Mod discharge, we demonstrate that the corresponding synchrotron image is well-reproduced by SOFT simulations, and we explain how it can be understood in terms of the parameter scans. Geometric effects are shown to significantly influence the synchrotron spectrum, and we show that inherent inconsistencies in a simple emission model (i.e. not modeling detection) can lead to incorrect interpretation of the images.

physics.plasm-ph↗