arXiv subjects

Matteo Castellani

Publications and source records attributed to Matteo Castellani.

13 recordsLinked to original sources

arXiv2026

Reconfigurable Superconducting Logic for On-Chip Photon Coincidence Detection

Scaling photonic quantum-information platforms requires arrays of superconducting nanowire single-photon detectors (SNSPDs) for feedforward control, in which optical operations are conditioned on Bell-state measurements relying on photon-coincidence detections. On-chip superconducting cryotron electronics, performing logic on detector outputs and driving optical modulators, could reduce latency and room-temperature interconnect complexity for feedforward schemes. To date, no cryotron circuits designed for this purpose have been demonstrated. We demonstrate a bias-programmable logic gate based on three nanocryotrons (nTrons) that implements selectable AND (coincidence), XOR (odd-parity), and OR functions. It operates on two electrical pulses at 4.2 K, with bit-error rates below $10^{-3}$, bias margins up to $\pm21.7\%$, and operation extending to 25 MHz over narrower bias windows. It performs coincidence and odd-parity detection on two SNSPDs' outputs with bit-error rates below $3.2 \times 10^{-2}$. As proof-of-concept, we show that nTrons can drive capacitive loads up to 1.15 V, potentially enabling compatibility with electro-optic modulators in feedforward schemes.

physics.app-ph↗

arXiv2025

Fast-Recovery Epitaxial NbN Superconducting Nanowire Single-Photon Detectors with Saturated Efficiency at 1550 nm in Liquid Helium

Achieving both high internal efficiency and fast reset times at elevated temperatures remains challenging due to limited understanding of how film properties govern SNSPD performance. We demonstrate that epitaxial NbN films on sapphire enable simultaneous high efficiency and rapid response. We fabricate and characterize SNSPDs based on these films deposited via DC magnetron sputtering on c-cut sapphire. High-quality epitaxial growth preserves a low electron diffusion coefficient and promotes strong electron-phonon coupling, yielding a high critical temperature and efficient hotspot formation in the dirty limit. X-ray diffraction and transmission electron microscopy confirm epitaxial alignment and lattice order. Nanowires of 20 nm width exhibit saturated internal efficiency at 1550 nm wavelength and short reset times at 4.2 K, enabled by lattice matching and high thermal conductance of the sapphire interface. Ab initio modeling reproduces photon count rates, linking device performance quantitatively to film properties such as diffusivity and electron-phonon coupling.

physics.app-ph↗

arXiv2025

Time-tagging data acquisition system for testing superconducting electronics based on an RFSoC and custom analog frontend

Novel electronic devices can often be operated in a plethora of ways, which makes testing circuits comprised of them difficult. Often, no single tool can simultaneously analyze the operating margins, maximum speed, and failure modes of a circuit, particularly when the intended behavior of subcomponents of the circuit is not standardized. This work demonstrates a cost-effective time-domain data acquisition system for electronic circuits that enables more intricate verification techniques than are practical with conventional experimental setups. We use high-speed digital-to-analog converters and real-time multi-gigasample-per-second waveform processing to push experimental circuits beyond their maximum operating speed. Our custom time-tagging data capture firmware reduces memory requirements and can be used to determine when errors occur. The firmware is combined with a thermal-noise-limited analog frontend with 50 dB of dynamic range. Compared to currently available commercial test equipment that is seven times more expensive, this data acquisition system was able to operate a superconducting shift register at a nearly three-times-higher clock frequency (200 MHz vs. 80 MHz).

physics.ins-det↗

arXiv2025

Scalable Superconducting Nanowire Memory Array with Row-Column Addressing

Developing ultra-low-energy superconducting computing and fault-tolerant quantum computing will require scalable superconducting memory. While conventional superconducting logic-based memory cells have facilitated early demonstrations, their large footprint poses a significant barrier to scaling. Nanowire-based superconducting memory cells offer a compact alternative, but high error rates have hindered their integration into large arrays. In this work, we present a superconducting nanowire memory array designed for scalable row-column operation, achieving a functional density of 2.6$\,$Mb/cm$^{2}$. The array operates at $1.3\,$K, where we implement and characterize multi-flux quanta state storage and destructive readout. By optimizing write and read pulse sequences, we minimize bit errors while maximizing operational margins in a $4\times 4$ array. Circuit-level simulations further elucidate the memory cell's dynamics, providing insight into performance limits and stability under varying pulse amplitudes. We experimentally demonstrate stable memory operation with a minimum bit error rate of $10^{-5}$. These results suggest a promising path for scaling superconducting nanowire memories to high-density architectures, offering a foundation for energy-efficient memory in superconducting electronics.

physics.app-ph↗

arXiv2025

Ab initio modeling of nonequilibrium dynamics in superconducting detectors and qubits

Nonequilibrium quasiparticle (QP) and phonon dynamics are central to the operation of superconducting devices. Superconducting detectors, such as the superconducting nanowire single-photon detector, perform best when a large QP population is generated in response to small perturbations. Conversely, for superconducting qubits and topologically protected Majorana fermions, even relatively small QP densities can lead to significant performance degradation, and thus, ideal materials are less susceptible to QP poisoning. However, existing models of these devices lack a rigorous description of the QP and phonon dynamics, relying on approximations and phenomenology. In this article, we combine kinetic equations with density functional theory to model the nonequilibrium dynamics of a superconducting film ab initio. To demonstrate the universality of our model, we illustrate two examples: (1) we develop a model for the detection of single photons in superconducting nanowires, and (2) we calculate the energy-relaxation rate of a transmon qubit due to the presence of excess QPs. Our examples demonstrate from first principles that NbN is well-suited for single-photon detection and that Ta transmon qubits possess reduced sensitivity to QP poisoning relative to other materials, which is likely in part responsible for their longer coherence times. In contrast to previous models, our ab initio approach makes these predictions without experimental input and thus can be used to accelerate progress in device development. Moreover, by considering the full-bandwidth electron-phonon coupling, our approach can incorporate strong-coupling effects. Our methods effectively integrate ab initio materials modeling with nonequilibrium theory of superconductivity to perform practical modeling of superconducting devices, providing a comprehensive approach that connects fundamental theory with device applications.

cond-mat.supr-con↗

arXiv2024

Characterizing and modeling the influence of geometry on the performance of superconducting nanowire cryotrons

The scaling of superconducting nanowire-based devices to larger arrays is often limited by the cabling required to interface with each device. Cryogenic integrated circuits constructed from nanowire cryotrons, or nanocryotrons, can address this limitation by performing signal processing on chip. In this study, we characterize key performance metrics of the nanocryotron to elucidate its potential as a logical element in cryogenic integrated circuits and develop an electro-thermal model to connect material parameters with device performance. We find that the performance of the nanocryotron depends significantly on the device geometry, and trade-offs are associated with optimizing the gain, jitter, and energy dissipation. We demonstrate that nanocryotrons fabricated on niobium nitride can achieve a grey zone less than 210 nA wide for a 5 ns long input pulse corresponding to a maximum achievable gain of 48 dB, an energy dissipation of less than 20 aJ per operation, and a jitter of less than 60 ps.

cond-mat.supr-con↗

arXiv2024

A superconducting full-wave bridge rectifier

Superconducting thin-film electronics are attractive for their low power consumption, fast operating speeds, and ease of interface with cryogenic systems such as single-photon detector arrays, and quantum computing devices. However, the lack of a reliable superconducting two-terminal asymmetric device, analogous to a semiconducting diode, limits the development of power-handling circuits, fundamental for scaling up these technologies. Existing efforts to date have been limited to single-diode proofs of principle and lacked integration of multiple controllable and reproducible devices to form complex circuits. Here, we demonstrate a robust superconducting diode with tunable polarity using the asymmetric vortex surface barrier in niobium nitride micro-bridges, achieving a 43% peak rectification efficiency, and showing half-wave rectification up to 120 MHz. We then realize and integrate several such diodes into a bridge rectifier circuit on a single microchip that performs continuous full-wave rectification up to 3 MHz and AC-to-DC conversion of a 50 MHz signal in periodic bursts with an estimated peak power efficiency of 50%.

physics.app-ph↗

arXiv2024

Parameter extraction for a superconducting thermal switch (hTron) SPICE model

Efficiently simulating large circuits is crucial to the development of superconducting nanowire-based electronics. However, current simulation tools for this technology are not adapted to the scaling of circuit size and complexity. We focus on the multilayered heater-nanocryotron (hTron), a promising superconducting nanowire-based switch used in applications such as superconducting nanowire single-photon detector (SNSPD) readout. Previously, the hTron was modeled using traditional finite-element methods (FEM), which fall short in simulating systems at a larger scale. An empirical-based method would be better adapted to this task, enhancing both simulation speed and agreement with experimental data. In this work, we perform switching current and activation delay measurements on 17 hTron devices. We then develop a method for extracting physical fitting parameters used to characterize the devices. We build a SPICE behavioral model that reproduces the static and transient device behavior using these parameters, and validate it by comparing its performance to a model developed in prior work, showing an improvement in simulation time by several orders of magnitude. Our model provides circuit designers with a tool to help understand the hTron's behavior during all design stages, thus enabling broader use of the hTron across various new areas of application.

physics.app-ph↗

arXiv2023

Nanocryotron ripple counter integrated with a superconducting nanowire single-photon detector for megapixel arrays

Decreasing the number of cables that bring heat into the cryostat is a critical issue for all cryoelectronic devices. Especially, arrays of superconducting nanowire single-photon detectors (SNSPDs) could require more than $10^6$ readout lines. Performing signal processing operations at low temperatures could be a solution. Nanocryotrons, superconducting nanowire three-terminal devices, are good candidates for integrating sensing and electronics on the same technological platform as SNSPDs in photon-counting applications. In this work, we demonstrated that it is possible to read out, process, encode, and store the output of SNSPDs using exclusively superconducting nanowires. In particular, we present the design and development of a nanocryotron ripple counter that detects input voltage spikes and converts the number of pulses to an $N$-digit value. The counting base can be tuned from 2 to higher values, enabling higher maximum counts without enlarging the circuit. As a proof-of-principle, we first experimentally demonstrated the building block of the counter, an integer-$N$ frequency divider with $N$ ranging from 2 to 5. Then, we demonstrated photon-counting operations at 405 nm and 1550 nm by coupling an SNSPD with a 2-digit nanocryotron counter partially integrated on-chip. The 2-digit counter could operate in either base 2 or base 3 with a bit error rate lower than $2 \times 10^{-4}$ and a count rate of $10^7\,$s$^{-1}$. We simulated circuit architectures for integrated readout of the counter state, and we evaluated the capabilities of reading out an SNSPD megapixel array that would collect up to $10^{12}$ counts per second. The results of this work, combined with our recent publications on a nanocryotron shift register and logic gates, pave the way for the development of nanocryotron processors, from which multiple superconducting platforms may benefit.

physics.app-ph↗

arXiv2023

A Superconducting Nanowire Binary Shift Register

We present a design for a superconducting nanowire binary shift register, which stores digital states in the form of circulating supercurrents in high-kinetic-inductance loops. Adjacent superconducting loops are connected with nanocryotrons, three terminal electrothermal switches, and fed with an alternating two-phase clock to synchronously transfer the digital state between the loops. A two-loop serial-input shift register was fabricated with thin-film NbN and achieved a bit error rate less than $10^{-4}$, operating at a maximum clock frequency of $83\,\mathrm{MHz}$ and in an out-of-plane magnetic field up to $6\,\mathrm{mT}$. A shift register based on this technology offers an integrated solution for low-power readout of superconducting nanowire single photon detector arrays, and is capable of interfacing directly with room-temperature electronics and operating unshielded in high magnetic field environments.

physics.app-ph↗

arXiv2022

A Nanocryotron Memory and Logic Family

The development of superconducting electronics based on nanocryotrons has been limited so far to few-device circuits, in part due to the lack of standard and robust logic cells. Here, we introduce and experimentally demonstrate designs for a set of nanocryotron-based building blocks that can be configured and combined to implement memory and logic functions. The devices were fabricated by patterning a single superconducting layer of niobium nitride and measured in liquid helium on a wide range of operating points. The tests show $10^{-4}$ bit error rates with above $20\,\%$ margins up to $50\,$MHz and the possibility of operating under the effect of a perpendicular $36\,$mT magnetic field, with $30\,\%$ margins at $10\,$MHz. Additionally, we designed and measured an equivalent delay flip-flop made of two memory cells to show the possibility of combining multiple building blocks to make larger circuits. These blocks may constitute a solid foundation for the development of nanocryotron logic circuits and finite-state machines with potential applications in the integrated processing and control of superconducting nanowire single-photon detectors.

physics.app-ph↗

arXiv2021

A Superconducting Nanowire-based Architecture for Neuromorphic Computing

Neuromorphic computing is poised to further the success of software-based neural networks by utilizing improved customized hardware. However, the translation of neuromorphic algorithms to hardware specifications is a problem that has been seldom explored. Building superconducting neuromorphic systems requires extensive expertise in both superconducting physics and theoretical neuroscience. In this work, we aim to bridge this gap by presenting a tool and methodology to translate algorithmic parameters into circuit specifications. We first show the correspondence between theoretical neuroscience models and the dynamics of our circuit topologies. We then apply this tool to solve linear systems by implementing a spiking neural network with our superconducting nanowire-based hardware.

cs.ET↗

arXiv2020

A superconducting nanowire spiking element for neural networks

As the limits of traditional von Neumann computing come into view, the brain's ability to communicate vast quantities of information using low-power spikes has become an increasing source of inspiration for alternative architectures. Key to the success of these largescale neural networks is a power-efficient spiking element that is scalable and easily interfaced with traditional control electronics. In this work, we present a spiking element fabricated from superconducting nanowires that has pulse energies on the order of ~10 aJ. We demonstrate that the device reproduces essential characteristics of biological neurons, such as a refractory period and a firing threshold. Through simulations using experimentally measured device parameters, we show how nanowire-based networks may be used for inference in image recognition, and that the probabilistic nature of nanowire switching may be exploited for modeling biological processes and for applications that rely on stochasticity.

q-bio.NC↗