Searcharxiv⌕ Search

arXiv subjects

Md Moin Uddin Chowdhury

Publications and source records attributed to Md Moin Uddin Chowdhury.

16 recordsLinked to original sources

Optimizing Reinforcement Learning Training over Digital Twin Enabled Multi-fidelity Networks

In this paper, we investigate a novel digital network twin (DNT) assisted deep learning (DL) model training framework. In particular, we consider a physical network where a base station (BS) uses several antennas to serve multiple mobile users, and a DNT that is a virtual representation of the physical network. The BS must adjust its antenna tilt angles to optimize the data rates of all users. Due to user mobility, the BS may not be able to accurately track network dynamics such as wireless channels and user mobilities. Hence, a reinforcement learning (RL) approach is used to dynamically adjust the antenna tilt angles. To train the RL, we can use data collected from the physical network and the DNT. The data collected from the physical network is more accurate but incurs more communication overhead compared to the data collected from the DNT. Therefore, it is necessary to determine the ratio of data collected from the physical network and the DNT to improve the training of the RL model. We formulate this problem as an optimization problem whose goal is to jointly optimize the tilt angle adjustment policy and the data collection strategy, aiming to maximize the data rates of all users while constraining the time delay introduced by collecting data from the physical network. To solve this problem, we propose a hierarchical RL framework that integrates robust adversarial loss and proximal policy optimization (PPO). Simulation results show that our proposed method reduces the physical network data collection delay by up to 28.01% and 1x compared to a hierarchical RL that uses vanilla PPO as the first level RL, and the baseline that uses robust-RL at the first level and selects the data collection ratio randomly.

cs.NI↗

Through the telecom lens: Are all training samples important?

The rise of AI in telecommunications, from optimizing Radio Access Networks to managing user experience, has sharply increased data volumes and training demands. Telecom data is often noisy, high-dimensional, costly to store, process, and label. Despite Ai's critical role, standard workflows still assume all training samples contribute equally. On the other hand, next generation systems require AI models that are accurate, efficient, and sustainable.The paper questions the assumptions of equal importance by focusing on applying and analyzing the roles of individual samples in telecom training and assessing whether the proposed model optimizes computation and energy use. we perform sample-level gradient analysis across epochs to identify patterns of influence and redundancy in model learning. Based on this, we propose a sample importance framework thats electively prioritizes impactful data and reduces computation without compromising accuracy. Experiments on three real-world telecom datasets show that our method [reserves performance while reducing data needs and computational overhead while advancing the goals of sustainable AI in telecommunications.

cs.LG↗

Computation- and Communication-Efficient Online FL for Resource-Constrained Aerial Vehicles

Privacy-preserving distributed machine learning (ML) and aerial connected vehicle (ACV)-assisted edge computing have drawn significant attention lately. Since the onboard sensors of ACVs can capture new data as they move along their trajectories, the continual arrival of such 'newly' sensed data leads to online learning and demands carefully crafting the trajectories. Besides, as typical ACVs are inherently resource-constrained, computation- and communication-efficient ML solutions are needed. Therefore, we propose a computation- and communication-efficient online aerial federated learning (2CEOAFL) algorithm to take the benefits of continual sensed data and limited onboard resources of the ACVs. In particular, considering independently owned ACVs act as selfish data collectors, we first model their trajectories according to their respective time-varying data distributions. We then propose a 2CEOAFL algorithm that allows the flying ACVs to (a) prune the received dense ML model to make it shallow, (b) train the pruned model, and (c) probabilistically quantize and offload their trained accumulated gradients to the central server (CS). Our extensive simulation results show that the proposed 2CEOAFL algorithm delivers comparable performances to its non-pruned and nonquantized, hence, computation- and communication-inefficient counterparts.

cs.LG↗

Mobility State Detection of Cellular-Connected UAVs based on Handover Count Statistics

To ensure reliable and effective mobility management for aerial user equipment (UE), estimating the speed of cellular-connected unmanned aerial vehicles (UAVs) carries critical importance since this can help to improve the quality of service of the cellular network. The 3GPP LTE standard uses the number of handovers made by a UE during a predefined time period to estimate the speed and the mobility state efficiently. In this paper, we introduce an approximation to the probability mass function of handover count (HOC) as a function of a cellular-connected UAV's height and velocity, HOC measurement time window, and different ground base station (GBS) densities. Afterward, we derive the Cramer-Rao lower bound (CRLB) for the speed estimate of a UAV, and also provide a simple biased estimator for the UAV's speed which depends on the GBS density and HOC measurement period. Interestingly, for a low time-to-trigger (TTT) parameter, the biased estimator turns into a minimum variance unbiased estimator (MVUE). By exploiting this speed estimator, we study the problem of detecting the mobility state of a UAV as low, medium, or high mobility as per the LTE specifications. Using CRLBs and our proposed MVUE, we characterize the accuracy improvement in speed estimation and mobility state detection as the GBS density and the HOC measurement window increase. Our analysis also shows that the accuracy of the proposed estimator does not vary significantly with respect to the TTT parameter.

eess.SP↗

Wireless Connectivity and Localization for Advanced Air Mobility Services

By serving as an analog to traffic signal lights, communication signaling for drone to drone communications holds the key to the success of advanced air mobility (AAM) in both urban and rural settings. Deployment of AAM applications such as air taxis and air ambulances, especially at large-scale, requires a reliable channel for a point-to-point and broadcast communication between two or more aircraft. Achieving such high reliability, in a highly mobile environment, requires communication systems designed for agility and efficiency. This paper presents the foundations for establishing and maintaining a reliable communication channel among multiple aircraft in unique AAM settings. Subsequently, it presents concepts and results on wireless coverage and mobility for AAM services using cellular networks as a ground network infrastructure. Finally, we analyze the wireless localization performance at 3D AAM corridors when cellular networks are utilized, considering different corridor heights and base station densities. We highlight future research directions and open problems to improve wireless coverage and localization throughout the manuscript.

eess.SP↗

Ensuring Reliable Connectivity to Cellular-Connected UAVs with Up-tilted Antennas and Interference Coordination

To integrate unmanned aerial vehicles (UAVs) in future large-scale deployments, a new wireless communication paradigm, namely, the cellular-connected UAV has recently attracted interest. However, the line-of-sight dominant air-to-ground channels along with the antenna pattern of the cellular ground base stations (GBSs) introduce critical interference issues in cellular-connected UAV communications. In particular, the complex antenna pattern and the ground reflection (GR) from the down-tilted antennas create both coverage holes and patchy coverage for the UAVs in the sky, which leads to unreliable connectivity from the underlying cellular network. To overcome these challenges, in this paper, we propose a new cellular architecture that employs an extra set of co-channel antennas oriented towards the sky to support UAVs on top of the existing down-tilted antennas for ground user equipment (GUE). To model the GR stemming from the down-tilted antennas, we propose a path-loss model, which takes both antenna radiation pattern and configuration into account. Next, we formulate an optimization problem to maximize the minimum signal-to-interference ratio (SIR) of the UAVs by tuning the up-tilt (UT) angles of the up-tilted antennas. Since this is an NP-hard problem, we propose a genetic algorithm (GA) based heuristic method to optimize the UT angles of these antennas. After obtaining the optimal UT angles, we integrate the 3GPP Release-10 specified enhanced inter-cell interference coordination (eICIC) to reduce the interference stemming from the down-tilted antennas. Our simulation results based on the hexagonal cell layout show that the proposed interference mitigation method can ensure higher minimum SIRs for the UAVs over baseline methods while creating minimal impact on the SIR of GUEs.

eess.SP↗

Base Station Antenna Uptilt Optimization for Cellular-Connected Drone Corridors

The concept of drone corridors is recently getting more attention to enable connected, safe, and secure flight zones in the national airspace. To support beyond visual line of sight (BVLOS) operations of aerial vehicles in a drone corridor, cellular base stations (BSs) serve as a convenient infrastructure, since such BSs are widely deployed to provide seamless wireless coverage. However, antennas in the existing cellular networks are down-tilted to optimally serve their ground users, which results in coverage holes if they are also used to serve drones. In this letter, we consider the use of additional uptilted antennas at cellular BSs and optimize the uptilt angle to minimize outage probability for a given drone corridor. Our numerical results show how the beamwidth and the maximum drone corridor height affect the optimal value of the antenna uptilt angle.

eess.SP↗

A Digital Twin for Reconfigurable Intelligent Surface Assisted Wireless Communication

Reconfigurable Intelligent Surface (RIS) has emerged as one of the key technologies for 6G in recent years, which comprise a large number of low-cost passive elements that can smartly interact with the impinging electromagnetic waves for performance enhancement. However, optimally configuring massive number of RIS elements remains a challenge. In this paper, we present a novel digital-twin framework for RIS-assisted wireless networks which we name it Environment-Twin (Env-Twin). The goal of the Env-Twin framework is to enable automation of optimal control at various granularities. In this paper, we present one example of the Env-Twin models to learn the mapping function between the RIS configuration with measured attributes for the receiver location, and the corresponding achievable rate in an RIS-assisted wireless network without involving explicit channel estimation or beam training overhead. Once learned, our Env-Twin model can be used to predict optimal RIS configuration for any new receiver locations in the same wireless network. We leveraged deep learning (DL) techniques to build our model and studied its performance and robustness. Simulation results demonstrate that the proposed Env-Twin model can recommend near-optimal RIS configurations for test receiver locations which achieved close to an upper bound performance that assumes perfect channel knowledge. Our Env-Twin model was trained using less than 2% of the total receiver locations. This promising result represents great potential of the proposed Env-Twin framework for developing a practical RIS solution where the panel can automatically configure itself without requesting channel state information (CSI) from the wireless network infrastructure.

cs.NI↗

RL-Based Interference Mitigation in Uncoordinated Networks with Partially Overlapping Tones

Partially-overlapping tones (POT) are known to help mitigate co-channel interference in uncoordinated multi-carrier networks by introducing intentional frequency offsets (FOs) to the transmitted signals. In this paper, we explore the use of (POT) with reinforcement learning (RL) in dense networks where multiple links access time-frequency resources simultaneously. We propose a novel framework based on Q-learning, to obtain the (FO) for the multi-carrier waveform used for each link. In particular, we consider filtered multi-tone (FMT) systems that utilize Gaussian, root-raised-cosine (RRC), and isotropic orthogonal transform algorithm (IOTA) based prototype filters. Our simulation results show that the proposed scheme enhances the capacity of the links by at least 30\% in additive white Gaussian noise (AWGN) channel at high signal-to-noise ratio (SNR), and even more so in the presence of severe multi-path fading. For a wide range of interfering link densities, we demonstrate substantial improvements in the outage probability and multi-user efficiency facilitated by (POT), with the Gaussian filter outperforming the other two filters.

eess.SP↗

Mobility Management for Cellular-Connected UAVs: A Learning-Based Approach

The pervasiveness of the wireless cellular network can be a key enabler for the deployment of autonomous unmanned aerial vehicles (UAVs) in beyond visual line of sight scenarios without human control. However, traditional cellular networks are optimized for ground user equipment (GUE) such as smartphones which makes providing connectivity to flying UAVs very challenging. Moreover, ensuring better connectivity to a moving cellular-connected UAV is notoriously difficult due to the complex air-to-ground path loss model. In this paper, a novel mechanism is proposed to ensure robust wireless connectivity and mobility support for cellular-connected UAVs by tuning the downtilt (DT) angles of all the GBSs. By leveraging tools from reinforcement learning (RL), DT angles are dynamically adjusted by using a model-free RL algorithm. The goal is to provide efficient mobility support in the sky by maximizing the received signal quality at the UAV while also maintaining good throughput performance of the ground users. Simulation results show that the proposed RL-based mobility management (MM) technique can reduce the number of handovers while maintaining the performance goals, compared to the baseline MM scheme in which the network always keeps the DT angle fixed.

eess.SP↗

3D Trajectory Optimization in UAV-Assisted Cellular Networks Considering Antenna Radiation Pattern and Backhaul Constraint

This paper explores the effects of three-dimensional (3D) antenna radiation pattern and backhaul constraint on optimal 3D path planning problem of an unmanned aerial vehicle (UAV), in interference prevalent downlink cellular networks. We consider a cellular-connected UAV that is tasked to travel between two locations within a fixed time and it can be used to improve the cellular connectivity of ground users by acting as a relay. Since the antenna gain of a cellular base station changes significantly with the UAV altitude, the UAV can increase the signal quality in its backhaul link by changing its height over the course of its mission. This problem is non-convex and thus, we explore the dynamic programming technique to solve it. We show that the 3D optimal paths can introduce significant network performance gain over the trajectories with fixed UAV heights.

eess.SP↗

UAV Aided Search and Rescue Operation Using Reinforcement Learning

Owing to the enhanced flexibility in deployment and decreasing costs of manufacturing, the demand for unmanned aerial vehicles (UAVs) is expected to soar in the upcoming years. In this paper, we explore a UAV aided search and rescue~(SAR) operation in indoor environments, where the GPS signals might not be reliable. We consider a SAR scenario where the UAV tries to locate a victim trapped in an indoor environment by sensing the RF signals emitted from a smart device owned by the victim. To locate the victim as fast as possible, we leverage tools from reinforcement learning~(RL). Received signal strength~(RSS) at the UAV depends on the distance from the source, indoor shadowing, and fading parameters, and antenna radiation pattern of the receiver mounted on the UAV. To make our analysis more realistic, we model two indoor scenarios with different dimensions using commercial ray-tracing software. Then, the corresponding RSS values at each possible discrete UAV location are extracted and used in a Q-learning framework. Unlike the traditional location-based navigation approach that exploits GPS coordinates, our method uses the RSS to define the states and rewards of the RL algorithm. We compare the performance of the proposed method where directional and omnidirectional antennas are used. The results reveal that the use of directional antennas provides faster convergence rates than the omnidirectional antennas.

eess.SY↗

Handover-Count based Velocity Estimation of Cellular-Connected UAVs

Cellular-connected unmanned aerial vehicles (UAVs) are expected to play a major role in various civilian and commercial applications in the future. While existing cellular networks can provide wireless coverage to UAV user equipment (UE), such legacy networks are optimized for ground users which makes it challenging to provide reliable connectivity to aerial UEs. To ensure reliable and effective mobility management for aerial UEs, estimating the velocity of cellular-connected UAVs carries critical importance. In this paper, we introduce an approximate probability mass function (PMF) of handover count (HOC) for different UAV velocities and different ground base station (GBS) densities. Afterward, we derive the Cramer-Rao lower bound (CRLB) for the velocity estimate of a UAV, and also provide a simple unbiased estimator for the UAV's velocity which depends on the GBS density and HOC measurement time. Our simulation results show that the accuracy of velocity estimation increases with the GBS density and HOC measurement window. Moreover, the velocity of commercially available UAVs can be estimated efficiently with reasonable accuracy.

eess.SP↗

RSS-Based Q-Learning for Indoor UAV Navigation

In this paper, we focus on the potential use of unmanned aerial vehicles (UAVs) for search and rescue (SAR) missions in GPS-denied indoor environments. We consider the problem of navigating a UAV to a wireless signal source, e.g., a smartphone or watch owned by a victim. We assume that the source periodically transmits RF signals to nearby wireless access points. Received signal strength (RSS) at the UAV, which is a function of the UAV and source positions, is fed to a Q-learning algorithm and the UAV is navigated to the vicinity of the source. Unlike the traditional location-based Q-learning approach that uses the GPS coordinates of the agent, our method uses the RSS to define the states and rewards of the algorithm. It does not require any a priori information about the environment. These, in turn, make it possible to use the UAVs in indoor SAR operations. Two indoor scenarios with different dimensions are created using a ray tracing software. Then, the corresponding heat maps that show the RSS at each possible UAV location are extracted for more realistic analysis. Performance of the RSS-based Q-learning algorithm is compared with the baseline (location-based) Q-learning algorithm in terms of convergence speed, average number of steps per episode, and the total length of the final trajectory. Our results show that the RSS-based Q-learning provides competitive performance with the location-based Q-learning.

eess.SP↗

Effects of 3D Antenna Radiation and Two-Hop Relaying on Optimal UAV Trajectory in Cellular Networks

In this paper, considering an interference limited inband downlink cellular network, we study the effects of scheduling criteria, mobility constraints, path loss models, backhaul constraints, and 3D antenna radiation pattern on trajectory optimization problem of an unmanned aerial vehicle (UAV). In particular, we consider a UAV that is tasked to travel between two locations within a given amount of time (e.g., for delivery or surveillance purposes), and we consider that such a UAV can be used to improve cellular connectivity of mobile users by serving as a relay for the terrestrial network. As the optimization problem is hard to solve numerically, we explore the dynamic programming (DP) technique for finding the optimum UAV trajectory. We utilize capacity and coverage performance of the terrestrial network while studying all the effects of different techniques and phenomenon. Extensive simulations show that the maximum sum-rate trajectory provides the best per user capacity whereas, the optimal proportional fair (PF) rate trajectory provides higher coverage probability than the other two. Since, the generated trajectories are infeasible for the UAV to follow exactly as it can not take sharp turns due to kinematic constraints, we generate smooth trajectory using Bezier curves. Our results show that the cellular capacity using the Bezier curves is close to the capacity observed when using the optimal trajectories.

eess.SP↗

Trajectory Optimization in UAV-Assisted Cellular Networks under Mission Duration Constraint

In this paper, we address the problem of finding the optimal trajectory for an unmanned aerial vehicle (UAV) for improving the wireless coverage of a terrestrial cellular network. In particular, we consider a UAV that is tasked to travel from one point to another within a given time constraint, and it can also simultaneously assist the cellular network by providing wireless coverage during its mission. Considering an interference limited downlink of a cellular network, we formulate an optimization problem for maximizing the proportional-fair (PF) data rate of the cellular network and explore dynamic programming (DP) technique for finding the optimum UAV trajectory. We also explore the optimal UAV trajectories associated with maximum sum-rate and 5th percentile spectral efficiency (5pSE) rate and compare the capacity and coverage performance of the three approaches. Numerical simulations show that the maximum sum-rate trajectory provides the best per user capacity whereas, the optimal PF trajectory yields higher coverage probability than the other two trajectories. The optimal trajectories are generally infeasible to follow exactly as the UAVs can not take sharp turns due to kinematic constraints. Hence, we generate smooth trajectories using Bezier curve.

eess.SP↗