arXiv subjects

Michel Piat

Publications and source records attributed to Michel Piat.

16 recordsLinked to original sources

arXiv2026

Flux jump correction in the QUBIC TES data pipeline

Flux jumps occur in the readout electronics of Transition Edge Sensor (TES) detectors coupled to Superconducting Quantum Interference Devices (SQUIDs), as a consequence of the periodic transfer function of SQUIDs in the superconducting regime. These events manifest as discontinuities in the Time Ordered Data (TOD) and can significantly degrade the quality of the measured signals. In this work, we present an automated pipeline to identify and correct flux jumps in the calibration data of the QUBIC (Q \& U Bolometric Interferometer for Cosmology) instrument, designed to measure the B-mode polarization of the Cosmic Microwave Background (CMB). Using data from multiple observation campaigns, we characterize the statistical properties of flux jumps and compare them with expectations based on the electronic configuration of the instrument. The proposed pipeline successfully corrects these events, allowing the recovery of affected data and enabling their use in subsequent CMB analysis.

astro-ph.IM↗

arXiv2026

Joint Estimation of Properties of the Lunar Subsurface and Galactic Foregrounds with LuSEE-Night

The Lunar Surface Electromagnetics Experiment (LuSEE-Night) is a joint NASA-DOE-ESA low-frequency radio telescope that will reach the lunar far side in 2027. The unknown dielectric properties of the subsurface at the LuSEE-Night landing site impose the most significant limitation for precision instrument calibration, as reflections from the lunar subsurface can change the primary beam at the 10-20% level. Simulations of these effects have provided insight and concern, showing that the lunar subsurface modeled as a lossy dielectric can absorb a large amount of the power of the sky signal. While this absorption may not strongly impact the signal-to-noise ratio in a sky-noise-dominated regime, it could complicate the beam pattern and make the signal more difficult to model and interpret. We have simulated the far-field properties of the LuSEE-Night beam for varying dielectric profiles of the lunar subsurface. We find that varying the properties of the lunar subsurface has the most significant impact around the antenna resonance, impacting its amplitude, position and width. Conversely, changing the properties of the foreground impacts the data across the band. We use a Bayesian inference pipeline to jointly estimate parameters of a galactic foreground model and dielectric properties of the lunar subsurface around the LuSEE-Night landing site and find that parameters of both the galaxy and subsurface properties can be estimated jointly. While the modeling is somewhat idealized, we believe that the results are largely robust owing to the fact that spectral variations for plausible subsurface and galaxy models have very different spectral signatures.

astro-ph.IM↗

arXiv2026

High efficiency superconducting filterbank with impedance-defined resolution for millimeter-wave spectroscopy

We present a high efficiency, moderate resolution on-chip superconducting filterbank spectrometer designed for line intensity mapping and broadband wave-like dark matter searches. Existing implementations used by the millimeter-wave community rely on resistive feedline termination for standing wave mitigation which caps the per-channel efficiency $\eta_\mathrm{ch}$ at 50\% and utilize microstrip resonators which highly couple the resolving power $\mathcal{R}=\nu/\delta\nu$ and $\eta_\mathrm{ch}$ to thin-film dielectric loss. The architecture presented in this paper addresses these limitations by eliminating the termination resistor and employing niobium coplanar waveguide resonators patterned directly on single-crystal silicon, which fixes the resonator's internal quality factor by the silicon substrate property rather than by the loss tangent of a deposited film. The resolving power is set by the impedance ratio between the resonator and feedline. Electromagnetic and circuit simulations of a ten-channel filterbank near 90~GHz at unity oversampling show $\mathcal{R}=1170$ and $\eta_\mathrm{ch}> 78\%$, with no significant trend in efficiency across channels. A ten-channel prototype, designed for $\mathcal{R}=92\pm5$ and $\eta_\mathrm{ch}=(81\pm3)\%$ over 90--106~GHz with a 560~nm interlayer based on simulations, was fabricated and optically characterized, yielding $\mathcal{R}=208\pm74$ and $\eta_\mathrm{ch}=(77\pm6)\%$. Measured $\eta_\mathrm{ch}$ well above the 50\% termination limit, together with demonstrated impedance tuning of $\mathcal{R}$, validate the design principles of this filterbank spectrometer and establishes a route to high-efficiency, high-resolution on-chip spectrometer arrays.

astro-ph.IM↗

arXiv2026

Linear map-making with LuSEE-Night

LuSEE-Night is a pathfinder radio telescope on the lunar far side employing four 3-m monopole antennas arranged as two horizontal cross pseudo-dipoles on a rotational stage and sensitive to the radio sky in the 1-50 MHz frequency band. LuSEE-Night measures the corresponding 16 correlation products as a function of frequency. While each antenna combination measures radiation coming from a large area of the sky, their aggregate information as a function of phase in the lunar cycle and rotational stage position can be deconvolved into a low-resolution map of the sky. We study this deconvolution using linear map-making based on the Wiener filter algorithm. We illustrate how systematic effects can be effectively marginalised over as contributions to the noise covariance and demonstrate this technique on beam knowledge uncertainty and gain fluctuations. With reasonable assumptions about instrument performance, we show that LuSEE-Night should be able to map the sub-50 MHz sky at a ~5-degree resolution.

astro-ph.IM↗

arXiv2025

Fast far-sidelobe modeling for centimeter to sub-millimeter astrophysical observations

Next-generation centimeter to sub-millimeter telescopes require exquisite control over instrumental far-sidelobe response to accurately measure faint signals like the Cosmic Microwave Background B modes. Because existing electromagnetic modeling methods are computationally expensive, we developed a novel, diffraction-based beam modeling method for rapid and low-cost calculations. We applied this methodology to model the BICEP3 far-sidelobes and found good qualitative agreement with in situ beam measurements. Using this validated simulated beam, we calculated the sidelobe temperature pickup for a specific observation scenario: scanning near the slopes of Cerro Toco in the Atacama Desert. This rapid, predictive framework is most valuable as a tool for optimizing instrument baffling and identifying efficient scan strategies during the conceptual design phase.

astro-ph.IM↗

arXiv2025

A novel double-rim forebaffle design for centimeter to sub-millimeter astrophysical observations

Stray radiation of various origin is a major source of degradation of centimeter to sub-millimeter astronomical observations. This is particularly problematic for the detection of signals such as faint cosmic microwave background polarization B modes, or for mapping large-scale extragalactic or Galactic diffuse emission. In this paper, we propose a double-rim forebaffle design to reduce the impact of such stray radiation contamination. Using qualitative arguments and numerical simulations, we show that such a design has the potential to substantially improve the quality of future observations.

astro-ph.IM↗

arXiv2024

Investigation of reflection-based measurements of microwave kinetic inductance detectors in the optical bands

In this paper, we investigate the single photon response from the reflection of the Microwave Kinetic Inductance Detector (MKID) array. Reflection measurements are carried out using two configurations: one is measured simultaneously with the transmission, and the other is obtained with a single-ended MKID array terminated with an open load. Compared with the transmission, reflection measurements significantly reduce the readout noise of the single-ended MKID array. This is also reflected in the improvement of the median energy resolving power by around 20%-30% under pulsed photon illumination at $λ= 405$~nm, mainly due to an increase in the size of the resonance circle on the IQ plane. This method has the potential to be used to read out large MKID arrays.

astro-ph.IM↗

arXiv2024

Investigation of Quasi-particle Relaxation in Strongly Disordered Superconductor Resonators

In this paper, we investigate the quasi-particle (QP) relaxation of strongly disordered superconducting resonators under optical illumination at different bath temperatures with the Rothwarf and Taylor equations and the gap-broadening theory described by the Usadal equation. The analysis is validated with various single-photon responses of Titanium Nitride (TiN) microwave kinetic inductance detectors (MKIDs) under pulsed 405~nm laser illumination. The QP relaxation in TiN is dominated by QPs with energy below the energy gap smeared by the disorder, and its duration is still inversely proportional to the QP density. The QP lifetime versus temperature can be fitted. The relaxation of the resonator can be further modeled with QP diffusion. The fitted QP diffusion coefficient of TiN is significantly smaller than expected. Our result also shows a significant increase in QP generation efficiency as the bath temperature increases.

cond-mat.supr-con↗

arXiv2023

Development of MKIDs in the Optical and Near-infrared Bands for SPIAKID

SpectroPhotometric Imaging in Astronomy with Kinetic Inductance Detectors (SPIAKID) aims at designing, building, and deploying on the sky a spectrophotometric imager based on microwave kinetic inductance detectors (MKIDs) in the optical and near-infrared bands. MKIDs show a fast response and the ability to resolve photon energy compared to the conventional Charge-coupled Devices (CCDs). In this paper, we present the design and simulation of the MKID arrays for SPIAKID. The detectors consist of four arrays with each array of 20,000 lumped-element pixels, and each array will be read with 10 readout lines. %The array is designed to have resonances between 4-8GHz with a frequency spacing of 2 MHz and a coupling quality factor (Qc) of about 50000. The meander material of the resonators is trilayer TiN/Ti/TiN to have better uniformity of the critical temperature across the array. We also present the measurement result for a test array with $30\times30$ pixels which is a subset of the designed 2000-pixel array to verify the design and fabrication. The current measured best energy resolving power $R = E/ΔE$ is 2.4 at $λ= 405~$nm and the current medium R is around 1.7. We have also observed the response of the TiN/Ti/TiN is much smaller than expected.

astro-ph.IM↗

arXiv2022

Investigation of Optical Coupling in Microwave Kinetic Inductance Detectors using Superconducting Reflective Plates

To improve the optical coupling in Microwave Kinetic Inductance Detectors (MKIDs), we investigate the use of a reflective plate beneath the meandered absorber. We designed, fabricated and characterized high-Q factors TiN-based MKIDs on sapphire operating at optical wavelengths with a Au/Nb reflective thin bilayer below the meander. The reflector is set at a quarter-wave distance from the meander using a transparent Al$_2$O$_3$ dielectric layer to reach the peak photon absorption. We expect the plate to recover undetected photons by reflecting them back onto the absorber.

physics.ins-det↗

arXiv2021

Large Inverse Transient Phase Response of Titanium-nitride-based Microwave Kinetic Inductance Detectors

Following optical pulses ($λ=405~\text{nm}$) on titanium nitride (TiN) Microwave Kinetic Inductance Detectors (MKIDs) cooled down at temperatures $T \le T_c / 20$ ($T_c \simeq 4.6~\text{K}$), we observe a large phase-response highlighting two different modes simultaneously that are nevertheless related. The first corresponds to the well-known transition of cooper-pair breaking into quasi-particles which produces a known phase response. This is immediately followed by a large inverse response lasting several hundreds of microseconds to several milliseconds depending on the temperature. We propose to model this inverse pulse as the thermal perturbation of the superconductor and interaction with two level system (TLS) that reduces the dielectric constant which in turns modify the capacitance and therefore the resonance frequency. The ratio of the TLS responding to the illumination is on the order of that of the area of the inductor to the whole resonator

astro-ph.IM↗

arXiv2019

QUBIC: Exploring the primordial Universe with the Q\&U Bolometric Interferometer

In this paper we describe QUBIC, an experiment that will observe the polarized microwave sky with a novel approach, which combines the sensitivity of state-of-the art bolometric detectors with the systematic effects control typical of interferometers. QUBIC unique features are the so-called "self-calibration", a technique that allows us to clean the measured data from instrumental effects, and its spectral imaging power, i.e. the ability to separate the signal in various sub-bands within each frequency band. QUBIC will observe the sky in two main frequency bands: 150 GHz and 220 GHz. A technological demonstrator is currently under testing and will be deployed in Argentina during 2019, while the final instrument is expected to be installed during 2020.

astro-ph.IM↗

arXiv2017

Exploring cosmic origins with CORE: gravitational lensing of the CMB

Lensing of the CMB is now a well-developed probe of large-scale clustering over a broad range of redshifts. By exploiting the non-Gaussian imprints of lensing in the polarization of the CMB, the CORE mission can produce a clean map of the lensing deflections over nearly the full-sky. The number of high-S/N modes in this map will exceed current CMB lensing maps by a factor of 40, and the measurement will be sample-variance limited on all scales where linear theory is valid. Here, we summarise this mission product and discuss the science that it will enable. For example, the summed mass of neutrinos will be determined to an accuracy of 17 meV combining CORE lensing and CMB two-point information with contemporaneous BAO measurements, three times smaller than the minimum total mass allowed by neutrino oscillations. In the search for B-mode polarization from primordial gravitational waves with CORE, lens-induced B-modes will dominate over instrument noise, limiting constraints on the gravitational wave power spectrum amplitude. With lensing reconstructed by CORE, one can "delens" the observed polarization internally, reducing the lensing B-mode power by 60%. This improves to 70% by combining lensing and CIB measurements from CORE, reducing the error on the gravitational wave amplitude by 2.5 compared to no delensing (in the null hypothesis). Lensing measurements from CORE will allow calibration of the halo masses of the 40000 galaxy clusters that it will find, with constraints dominated by the clean polarization-based estimators. CORE can accurately remove Galactic emission from CMB maps with its 19 frequency channels. We present initial findings that show that residual Galactic foreground contamination will not be a significant source of bias for lensing power spectrum measurements with CORE. [abridged]

astro-ph.CO↗

arXiv2013

PRISM (Polarized Radiation Imaging and Spectroscopy Mission): A White Paper on the Ultimate Polarimetric Spectro-Imaging of the Microwave and Far-Infrared Sky

PRISM (Polarized Radiation Imaging and Spectroscopy Mission) was proposed to ESA in response to the Call for White Papers for the definition of the L2 and L3 Missions in the ESA Science Programme. PRISM would have two instruments: (1) an imager with a 3.5m mirror (cooled to 4K for high performance in the far-infrared---that is, in the Wien part of the CMB blackbody spectrum), and (2) an Fourier Transform Spectrometer (FTS) somewhat like the COBE FIRAS instrument but over three orders of magnitude more sensitive. Highlights of the new science (beyond the obvious target of B-modes from gravity waves generated during inflation) made possible by these two instruments working in tandem include: (1) the ultimate galaxy cluster survey gathering 10e6 clusters extending to large redshift and measuring their peculiar velocities and temperatures (through the kSZ effect and relativistic corrections to the classic y-distortion spectrum, respectively) (2) a detailed investigation into the nature of the cosmic infrared background (CIB) consisting of at present unresolved dusty high-z galaxies, where most of the star formation in the universe took place, (3) searching for distortions from the perfect CMB blackbody spectrum, which will probe a large number of otherwise inaccessible effects (e.g., energy release through decaying dark matter, the primordial power spectrum on very small scales where measurements today are impossible due to erasure from Silk damping and contamination from non-linear cascading of power from larger length scales). These are but a few of the highlights of the new science that will be made possible with PRISM.

astro-ph.CO↗

arXiv2009

A demonstrator for bolometric interferometry

Bolometric Interferometry (BI) is one of the most promising techniques for precise measurements of the Cosmic Microwave Background polarization. In this paper, we present the results of DIBO (Demonstrateur d'Interferometrie Bolometrique), a single-baseline demonstrator operating at 90 GHz, built to proof the validity of the BI concept applied to a millimeter-wave interferometer. This instrument has been characterized in the laboratory with a detector at room temperature and with a 4 K bolometer. This allowed us to measure interference patterns in a clean way, both (1) rotating the source and (2) varying with time the phase shift among the two interferometer's arms. Detailed modelisation has also been performed and validated with measurements.

astro-ph.IM↗

arXiv2006

Probing neutrino masses with CMB lensing extraction

We evaluate the ability of future cosmic microwave background (CMB) experiments to measure the power spectrum of large scale structure using quadratic estimators of the weak lensing deflection field. We calculate the sensitivity of upcoming CMB experiments such as BICEP, QUaD, BRAIN, ClOVER and PLANCK to the non-zero total neutrino mass M_nu indicated by current neutrino oscillation data. We find that these experiments greatly benefit from lensing extraction techniques, improving their one-sigma sensitivity to M_nu by a factor of order four. The combination of data from PLANCK and the SAMPAN mini-satellite project would lead to sigma(M_nu) = 0.1 eV, while a value as small as sigma(M_nu) = 0.035 eV is within the reach of a space mission based on bolometers with a passively cooled 3-4 m aperture telescope, representative of the most ambitious projects currently under investigation. We show that our results are robust not only considering possible difficulties in subtracting astrophysical foregrounds from the primary CMB signal but also when the minimal cosmological model (Lambda Mixed Dark Matter) is generalized in order to include a possible scalar tilt running, a constant equation of state parameter for the dark energy and/or extra relativistic degrees of freedom.

astro-ph↗