arXiv subjects

Mohammad Dehghani Soltani

Publications and source records attributed to Mohammad Dehghani Soltani.

18 recordsLinked to original sources

arXiv2024

Interference Mitigation using Optimized Angle Diversity Receiver in LiFi Cellular Network

Light-fidelity (LiFi) is an emerging technology for high-speed short-range mobile communications. Inter-cell interference (ICI) is an important issue that limits the system performance in an optical attocell network. Angle diversity receivers (ADRs) have been proposed to mitigate ICI. In this paper, the structure of pyramid receivers (PRs) and truncated pyramid receivers (TPRs) are studied. The coverage problems of PRs and TPRs are defined and investigated, and the lower bound of field of view (FOV) for each PD is given analytically. The impact of random device orientation and diffuse link signal propagation are taken into consideration. The performances of PRs and TPRs are compared and then optimized ADR structures are proposed. The performance comparison between the select best combining (SBC) and maximum ratio combining (MRC) is given under different noise levels. It is shown that SBC will outperform MRC in an interference limited system, otherwise, MRC is a preferred scheme. In addition, the double source system, where each LiFi AP consists of two sources transmitting the same information signals but with opposite polarity, is proved to outperform the single source (SS) system under certain conditions.

cs.IT↗

arXiv2022

SPAD-Based Optical Wireless Communication with ACO-OFDM

The sensitivity of the optical wireless communication (OWC) can be effectively improved by employing the highly sensitive single-photon avalanche diode (SPAD) arrays. However, the nonlinear distortion introduced by the dead time strongly limits the throughput of the SPAD-based OWC systems. Optical orthogonal frequency division multiplexing (OFDM) can be employed in the systems with SPAD arrays to improve the spectral efficiency. In this work, a theoretical performance analysis of SPAD-based OWC system with asymmetrically-clipped optical OFDM (ACO-OFDM) is presented. The impact of the SPAD nonlinearity on the system performance is investigated. In addition, the comparison of the considered scheme with direct-current-biased optical OFDM (DCO-OFDM) is presented showing the distinct reliable operation regimes of the two schemes. In the low power regimes, ACO-OFDM outperforms DCO-OFDM; whereas, the latter is more preferable in the high power regimes.

cs.IT↗

arXiv2022

Terabit Indoor Laser-Based Wireless Communications: LiFi 2.0 for 6G

This paper provides a summary of available technologies required for implementing indoor laser-based wireless networks capable of achieving aggregate data-rates of terabits per second as widely accepted as a sixth generation (6G) key performance indicator. The main focus of this paper is on the technologies supporting the near infrared region of the optical spectrum. The main challenges in the design of the transmitter and receiver systems and communication/networking schemes are identified and new insights are provided. This paper also covers the previous and recent standards as well as industrial applications for optical wireless communications (OWC) and LiFi.

cs.IT↗

arXiv2022

Performance Analysis of SPAD-Based Optical Wireless Communication with OFDM

In recent years, there has been a growing interest in the use of single-photon avalanche diode (SPAD) in optical wireless communication (OWC). SPAD operates in the Geiger mode and can act as a photon counting receiver obviating the need for a transimpedance amplifier (TIA). Although a SPAD receiver can provide higher sensitivity compared to the traditional linear photodetectors, it suffers from the dead-time-induced nonlinearity. To improve the data rates of SPAD-based OWC systems, optical orthogonal frequency division multiplexing (OFDM) can be employed. This paper provides a comprehensive theoretical analysis of the SPAD-based OWC systems using OFDM signalling considering the effects of signal clipping, SPAD nonlinearity, and signal-dependent shot noise. An equivalent additive Gaussian noise channel model is proposed to describe the performance of the SPAD-based OFDM system. The statistics of the proposed channel model and the analytical expressions of the signal-to-noise ratio (SNR) and bit error rate (BER) are derived in closed forms. By means of extensive numerical results, the impact of the unique receiver nonlinearity on the system performance is investigated. The results demonstrate new insights into different optical power regimes of reliable operation for SPAD-based OFDM systems even well beyond SPAD saturation level.

cs.IT↗

arXiv2022

High-Speed Imaging Receiver Design for 6G Optical Wireless Communications: A Rate-FOV Trade-Off

The design of a compact high-speed and wide field of view (FOV) receiver is challenging due to the presence of two well-known trade-offs. The first one is the area-bandwidth trade-off of photodetectors (PDs) and the second one is the gain-FOV trade-off due to the use of optics. The combined effects of these two trade-offs imply that the achievable data rate of an imaging optical receiver is limited by its FOV, i.e., a rate-FOV trade-off. To control the area-bandwidth trade-off, an array of small PDs can be used instead of a single PD. Moreover, in practice, a large-area lens is required to ensure sufficient power collection, which in turn limits the receiver FOV (i.e., gain-FOV trade-off). We propose an imaging receiver design in the form of an array of arrays. To achieve a reasonable receiver FOV, we use individual focusing lens for each PD array rather than a single collection lens for the whole receiver. The proposed array of arrays structure provides an effective method to control both gain-FOV trade-off (via an array of lenses) and area-bandwidth trade-off (via arrays of PDs). We first derive a tractable analytical model for the SNR of an array of PDs where the maximum ratio combining has been employed. Then, we extend the model for the proposed array of arrays structure and the accuracy of the analytical model is verified based on several Optic Studio-based simulations. Next, we formulate an optimization problem to maximize the achievable data rate of the imaging receiver subject to a minimum required FOV. The optimization problem is solved for two commonly used modulation techniques, namely, OOK and direct current biased optical orthogonal frequency division multiplexing with variable rate quadrature amplitude modulation. It is demonstrated that a data rate of ~ 24 Gbps with a FOV of 15 is achievable using OOK with a total receiver size of 2 cm by 2 cm.

cs.IT↗

arXiv2022

A Tb/s Indoor MIMO Optical Wireless Backhaul System Using VCSEL Arrays

In this paper, the design of a multiple-input multiple-output (MIMO) optical wireless communication (OWC) link based on vertical cavity surface emitting laser (VCSEL) arrays is systematically carried out with the aim to support data rates in excess of 1 Tb/s for the backhaul of sixth generation (6G) indoor wireless networks. The proposed design combines direct current optical orthogonal frequency division multiplexing (DCO-OFDM) and a spatial multiplexing MIMO architecture. For such an ultra-high-speed line-of-sight (LOS) OWC link with low divergence laser beams, maintaining alignment is of high importance. In this paper, two types of misalignment error between the transmitter and receiver are distinguished, namely, radial displacement error and orientation angle error, and they are thoroughly modeled in a unified analytical framework assuming Gaussian laser beams, resulting in a generalized misalignment model (GMM). The derived GMM is then extended to MIMO arrays and the performance of the MIMO-OFDM OWC system is analyzed in terms of the aggregate data rate. Novel insights are provided into the system performance based on computer simulations by studying various influential factors such as beam waist, array configuration and different misalignment errors, which can be used as guidelines for designing short range Tb/s MIMO OWC systems.

cs.IT↗

arXiv2021

A VCSEL Array Transmission System with Novel Beam Activation Mechanisms

Optical wireless communication (OWC) is considered to be a promising technology which will alleviate traffic burden caused by the increasing number of mobile devices. In this study, a novel vertical-cavity surface-emitting laser (VCSEL) array is proposed for indoor OWC systems. To activate the best beam for a mobile user, two beam activation methods are proposed for the system. The method based on a corner-cube retroreflector (CCR) provides very low latency and allows real-time activation for high-speed users. The other method uses the omnidirectional transmitter (ODTx). The ODTx can serve the purpose of uplink transmission and beam activation simultaneously. Moreover, systems with ODTx are very robust to the random orientation of a user equipment (UE). System level analyses are carried out for the proposed VCSEL array system. For a single user scenario, the probability density function (PDF) of the signal-to-noise ratio (SNR) for the central beam of the VCSEL array system can be approximated as a uniform distribution. In addition, the average data rate of the central beam and its upper bound are given analytically and verified by Monte-Carlo simulations. For a multi-user scenario, an analytical upper bound for the average data rate is given. The effects of the cell size and the full width at half maximum (FWHM) angle on the system performance are studied. The results show that the system with a FWHM angle of $4^\circ$ outperforms the others.

cs.IT↗

arXiv2021

Safety Analysis for Laser-based Optical Wireless Communications: A Tutorial

Light amplification by stimulated emission of radiation (laser) sources have many advantages for use in high data rate optical wireless communications. In particular, the low cost and high-bandwidth properties of laser sources such as vertical-cavity surface-emitting lasers (VCSELs) make them attractive for future indoor optical wireless communications. In order to be integrated into future indoor networks, such lasers should conform to eye safety regulations determined by the international electrotechnical commission (IEC) standards for laser safety. In this paper, we provide a detailed study of beam propagation to evaluate the received power of various laser sources, based on which as well as the maximum permissible exposure (MPE) defined by the IEC 60825-1:2014 standard, we establish a comprehensive framework for eye safety analyses. This framework allows us to calculate the maximum allowable transmit power, which is crucial in the design of a reliable and safe laser-based wireless communication system. Initially, we consider a single-mode Gaussian beam and calculate the maximum permissible transmit power. Subsequently, we generalize this approach for higher-mode beams. It is shown that the M-squared-based approach for analysis of multimode lasers ensures the IEC eye safety limits, however, in some scenarios, it can be too conservative compared to the precise beam decomposition method. Laser safety analyses with consideration of optical elements such as lens and diffuser, as well as for VCSEL array have been also presented. Skin safety, as another significant factor of laser safety, has also been investigated in this paper. We have studied the impacts of various parameters such as wavelength, exposure duration and the divergence angle of laser sources on the safety analysis by presenting insightful results.

cs.IT↗

arXiv2020

End-to-End Energy Efficiency Evaluation for B5G Ultra Dense Networks

Energy efficiency (EE) is a major performance metric for fifth generation (5G) and beyond 5G (B5G) wireless communication systems, especially for ultra dense networks. This paper proposes an end-to-end (e2e) power consumption model and studies the energy efficiency for a heterogeneous B5G cellular architecture that separates the indoor and outdoor communication scenarios in ultra dense networks. In this work, massive multiple-input-multiple-output (MIMO) technologies at conventional sub-6 GHz frequencies are used for long-distance outdoor communications. Light-Fidelity (LiFi) and millimeter wave (mmWave) technologies are deployed to provide a high data rate service to indoor users. Whereas, in the referenced nonseparated system, the indoor users communicate with the outdoor massive MIMO macro base station directly. The performance of these two systems are evaluated and compared in terms of the total power consumption and energy efficiency. The results show that the network architecture which separates indoor and outdoor communication can support a higher data rate transmission for less energy consumption, compared to non-separate communication scenario. In addition, the results show that deploying LiFi and mmWave IAPs can enable users to transmit at a higher data rate and further improve the EE.

eess.SP↗

arXiv2020

Invoking Deep Learning for Joint Estimation of Indoor LiFi User Position and Orientation

Light-fidelity (LiFi) is a fully-networked bidirectional optical wireless communication (OWC) that is considered a promising solution for high-speed indoor connectivity. Unlike in conventional radio frequency wireless systems, the OWC channel is not isotropic, meaning that the device orientation affects the channel gain significantly. However, due to the lack of proper channel models for LiFi systems, many studies have assumed that the receiver is vertically upward and randomly located within the coverage area, which is not a realistic assumption from a practical point of view. In this paper, novel realistic and measurement-based channel models for indoor LiFi systems are proposed. Precisely, the statistics of the channel gain are derived for the case of randomly oriented stationary and mobile LiFi receivers. For stationary users, two channel models are proposed, namely, the modified truncated Laplace (MTL) model and the modified Beta (MB) model. For LiFi users, two channel models are proposed, namely, the sum of modified truncated Gaussian (SMTG) model and the sum of modified Beta (SMB) model. Based on the derived models, the impact of random orientation and spatial distribution of LiFi users is investigated, where we show that the aforementioned factors can strongly affect the channel gain and system performance.

eess.SP↗

arXiv2020

Measurements-Based Channel Models for Indoor LiFi Systems

eess.SP↗

arXiv2020

Hybrid LiFi and WiFi Networks: A Survey

To tackle the rapidly growing number of mobile devices and their expanding demands for Internet services, network convergence is envisaged to integrate different technology domains. A recently proposed and promising approach to indoor wireless communications is integrating light fidelity (LiFi) and wireless fidelity (WiFi), namely a hybrid LiFi and WiFi network (HLWNet). This type of network combines the high-speed data transmission of LiFi and the ubiquitous coverage of WiFi. In this paper, we present a survey-style introduction to HLWNets, starting with a framework including the network structure, cell deployment, multiple access schemes, modulation techniques, illumination requirements and backhauling. Then, key performance metrics and recent achievements are reviewed. Further, the unique challenges faced by HLWNets are elaborated in many research directions, including user behavior modeling, interference management, handover and load balancing. Finally, we discuss the potential of HLWNets in application areas such as indoor positioning and physical layer security.

cs.IT↗

arXiv2019

Physical Layer Security for Visible Light Communication Systems: A Survey

Due to the dramatic increase in high data rate services and in order to meet the demands of the fifth-generation (5G) networks, researchers from both academia and industry are exploring advanced transmission techniques, new network architectures and new frequency spectrum such as the visible light spectra. Visible light communication (VLC) particularly is an emerging technology that has been introduced as a promising solution for 5G and beyond. Although VLC systems are more immune against interference and less susceptible to security vulnerabilities since light does not penetrate through walls, security issues arise naturally in VLC channels due to their open and broadcasting nature, compared to fiber-optic systems. In addition, since VLC is considered to be an enabling technology for 5G, and security is one of the 5G fundamental requirements, security issues should be carefully addressed and resolved in the VLC context. On the other hand, due to the success of physical layer security (PLS) in improving the security of radio-frequency (RF) wireless networks, extending such PLS techniques to VLC systems has been of great interest. Only two survey papers on security in VLC have been published in the literature. However, a comparative and unified survey on PLS for VLC from information theoretic and signal processing point of views is still missing. This paper covers almost all aspects of PLS for VLC, including different channel models, input distributions, network configurations, precoding/signaling strategies, and secrecy capacity and information rates. Furthermore, we propose a number of timely and open research directions for PLS-VLC systems, including the application of measurement-based indoor and outdoor channel models, incorporating user mobility and device orientation into the channel model, and combining VLC and RF systems to realize the potential of such technologies.

eess.SP↗

arXiv2019

Impact of Device Orientation on Error Performance of LiFi Systems

Most studies on optical wireless communications (OWCs) have neglected the effect of random orientation in their performance analysis due to the lack of a proper model for the random orientation. Our recent empirical-based research illustrates that the random orientation follows a Laplace distribution for a static user equipment (UE). In this paper, we analyze the device orientation and assess its importance on system performance. The reliability of an OWC channel highly depends on the availability and alignment of line-of-sight (LOS) links. In this study, the effect of receiver orientation including both polar and azimuth angles on the LOS channel gain are analyzed. The probability of establishing a LOS link is investigated and the probability density function (PDF) of signal-to-noise ratio (SNR) for a randomly-oriented device is derived. By means of the PDF of SNR, the bit-error ratio (BER) of DC-biased optical orthogonal frequency division multiplexing (DCO-OFDM) in additive white Gaussian noise (AWGN) channels is evaluated. A closed-form approximation for the BER of UE with random orientation is presented which shows a good match with Monte-Carlo simulation results. Furthermore, the impact of the UE's random motion on the BER performance has been assessed. Finally, the effect of random orientation on the average signal-to-interference-plus-noise ratio (SINR) in a multiple access points (APs) scenario is investigated.

cs.IT↗

arXiv2018

Bidirectional Optical Spatial Modulation for Mobile Users: Towards a Practical Design for LiFi Systems

Among the challenges of realizing the full potential of light-fidelity (LiFi) cellular networks are user mobility, random device orientation and blockage. We study the impact of those challenges on the performance of LiFi in an indoor environment using measurement-based channel models. We adopt spatial modulation (SM), which has been shown to be energy efficient in many applications, including LiFi. We consider two configurations for placing the photodiodes (PDs) on the user equipment (UE). The first one is referred to as the screen receiver (SR) whereby all the PDs are located on one face of the UE, whereas the other one is a multi-directional receiver (MDR), in which the PDs are located on different sides of the UE. The latter configuration was motivated by the fact that SR exhibited poor performance in the presence of random device orientation and blockage. We show that MDR outperforms SR by over $10$ dB at BER of $3.8\times10^{-3}$. Moreover, an adaptive access point (AP) selection scheme for SM is considered where the number of APs are chosen adaptively in an effort to achieve the lowest energy requirement for a target BER and spectral efficiency. The user performance with random orientation and blockage in the whole room is evaluated for sitting and walking activities. For the latter, we invoke the orientation-based random waypoint (ORWP) mobility model. We also study the performance of the underlying system on the uplink channel where the same techniques are used for the downlink channel. Specifically, as the transmitted uplink power is constrained, the energy efficiency of SM is evaluated analytically. It is shown that the multi-directional transmitter (MDT) with adaptive SM is highly energy efficient. As a benchmark, we compare the performance of the proposed framework to that of the conventional spatial multiplexing system, and demonstrate the superiority of the proposed one.

eess.SP↗

arXiv2018

Modeling the Random Orientation of Mobile Devices: Measurement, Analysis and LiFi Use Case

Light-fidelity (LiFi) is a networked optical wireless communication (OWC) solution for high-speed indoor connectivity for fixed and mobile optical communications. Unlike conventional radio frequency wireless systems, the OWC channel is not isotropic, meaning that the device orientation affects the channel gain significantly, particularly for mobile users. However, due to the lack of a proper model for device orientation, many studies have assumed that the receiver is vertically upward and fixed. In this paper, a novel model for device orientation based on experimental measurements of forty participants has been proposed. It is shown that the probability density function (PDF) of the polar angle can be modeled either based on a Laplace (for static users) or a Gaussian (for mobile users) distribution. In addition, a closed-form expression is obtained for the PDF of the cosine of the incidence angle based on which line-of-sight (LOS) channel gain is described in OWC channels. An approximation of this PDF based on the truncated Laplace is proposed and the accuracy of this approximation is confirmed by the Kolmogorov-Smirnov distance (KSD). Moreover, the statistics of the LOS channel gain are calculated and the random orientation of a user equipment (UE) is modeled as a random process. The influence of the random orientation on signal-to-noise-ratio (SNR) performance of OWC systems has been evaluated. Finally, an orientation-based random waypoint (ORWP) mobility model is proposed by considering the random orientation of the UE during the user's movement. The performance of ORWP is assessed on the handover rate and it is shown that it is important to take the random orientation into account.

cs.IT↗

arXiv2018

Terminal Orientation in OFDM-based LiFi Systems

Light-fidelity (LiFi) is a wireless communication technology that employs both infrared and visible light spectra to support multiuser access and user mobility. Considering the small wavelength of light, the optical channel is affected by the random orientation of a user equipment (UE). In this paper, a random process model for changes in the UE orientation is proposed based on data measurements. We show that the coherence time of the random orientation is in the order of hundreds of milliseconds. Therefore, an indoor optical wireless channel can be treated as a slowly-varying channel as its delay spread is typically in the order of nanoseconds. A study of the orientation model on the performance of direct-current-biased orthogonal frequency-division multiplexing (DC-OFDM) is also presented. The performance analysis of the DC-OFDM system incorporates the effect of diffuse link due to reflection and blockage by the user. The results show that the diffuse link and the blockage have significant effects, especially if the UE is located relatively far away from an access point (AP). It is shown that the effect is notable if the horizontal distance between the UE and the AP is greater than $1.5$ m in a typical $5\times3.5\times3$ m$^3$ indoor room.

eess.SP↗

arXiv2017

Bidirectional User Throughput Maximization Based on Feedback Reduction in LiFi Networks

Channel adaptive signalling, which is based on feedback, can result in almost any performance metric enhancement. Unlike the radio frequency (RF) channel, the optical wireless communications (OWCs) channel is fairly static. This feature enables a potential improvement of the bidirectional user throughput by reducing the amount of feedback. Light-Fidelity (LiFi) is a subset of OWCs, and it is a bidirectional, high-speed and fully networked wireless communication technology where visible light and infrared are used in downlink and uplink respectively. In this paper, two techniques for reducing the amount of feedback in LiFi cellular networks are proposed, i) Limited-content feedback (LCF) scheme based on reducing the content of feedback information and ii) Limited-frequency feedback (LFF) based on the update interval scheme that lets the receiver to transmit feedback information after some data frames transmission. Furthermore, based on the random waypoint (RWP) mobility model, the optimum update interval which provides maximum bidirectional user equipment (UE) throughput, has been derived. Results show that the proposed schemes can achieve better average overall throughput compared to the benchmark one-bit feedback and full-feedback mechanisms.

cs.IT↗