Searcharxiv⌕ Search

arXiv subjects

Mostafa Mo. Massoud

Publications and source records attributed to Mostafa Mo. Massoud.

3 recordsLinked to original sources

Direct-Ink-Writing of Soft Thin Film Force-Sensitive Resistors with Velostat and Printed-Carbon Sensing Elements

Flexible resistive force sensors are useful for wearable, rehabilitation, and human--machine interfaces, but their performance depends on sensing-material architecture and fabrication. This work presents a parameterized Voltera NOVA-based direct-ink-writing workflow using printed silver electrodes with multilayer Velostat sensing elements on PET and TPU substrates, together with an exploratory fully printed carbon architecture. Velostat sensors containing 1, 2, 4, and 6 sensing layers exhibited strongly nonlinear force--voltage responses, with the greatest sensitivity at low forces. Best-fit straight-line $R^2$ values ranged from 0.475 to 0.641, area-based hysteresis from 3.90\% to 7.47\%, and 5-min voltage drift from 1.9\% to 7.3\%, with no consistent monotonic relationship between layer count and these metrics. Selected PET6 and TPU6 devices showed less than 0.05~V change in peak output between the first and final 100 cycles of a 10,000-cycle test. Printed-carbon devices demonstrated the feasibility of a more fully printed architecture, but configurations with six or fewer layers saturated below approximately 0.5~N or were nonfunctional, while the eight-layer device responded primarily below approximately 2~N. These results establish the feasibility of the printed-electrode Velostat workflow while identifying printed sensing materials as a key area for further development.

cs.RO↗

Soft Robotic Exogloves for Dexterous Mobility -- Towards Personalized Rehabilitation

Soft robotic exogloves can provide hand rehabilitation and assistance. Fitting these gloves often relies on standardized measurements not tailored to the individual, limiting their effectiveness, especially for fine articulation necessary for dexterous manipulation. We present the design, fabrication, modeling, and testing of a personalized pneumatically-actuated soft robotic exoglove. The glove was fit to a user's hand with topological scans and fabricated with silicone mold casting. Finite element analysis (FEA) was performed to evaluate actuator bending and forces from physical human-robot interaction (pHRI) between an actuator and a simplified personalized biomechanical finger model. Pneumatic pressure control experiments were conducted to flex the user's finger with static and dynamic references. Fabrication results show that topological scans enable precise tailoring to hand anatomy. Simulations showed that anatomical personalization enables analysis of pHRI contact forces, and results indicate sufficient joint mobilization with non-ideal compression on the proximal phalanx. Pneumatic testing indicates that pressure control allows accurate and targeted mobility of the metacarpophalangeal (MCP) and proximal interphalangeal (PIP) joints with intrinsic stiffness. Testing of multiple designs showed that relaxing the strain-limiting layer improves actuator-to-finger joint alignment during actuation. This work presents personalization to the human hand in structural conformability, joint topology, modeling of pHRI contact, and time-dependent actuation-deformation profiles. This lays the groundwork for informing exoglove design optimization to enable assistance in dexterous manipulation and neuromuscular rehabilitation of fine motor skills.

cs.RO↗

Robust Silicone Pour Casting and Sensor Embedding Procedures for Soft Robotic Actuators

Soft robots are well-suited for applications such as rehabilitation and surgery that require adaptable and safe interaction with their environment. However, the challenges of reproducible and scalable fabrication of soft robots limit their real-world deployment. Various fabrication methods have been introduced, but many are labor-intensive and prone to human error. Therefore, traditional two-part pour casting remains an attractive option. This paper presents procedures for robust, repeatable, and scalable fabrication of soft pneumatic actuators using two-part pour casting. The presented methods prevent internal cavity clogging and ensure air-tight sealing. Additionally, a robust sensor embedding procedure for thin-film flex sensors is presented, which allows for accurate and repeatable data acquisition. Finite Element Modeling (FEM) of the soft actuator is performed to analyze stress and deformation from internal pressure loadings. Pneumatic actuation experiments with PID pressure control are performed. Automated image processing is used to calibrate the embedded flex sensor to bending angle measurements. Staircase and sinusoidal profile actuation experiments validate the performance of the fabricated actuator. Angle response experiments for the staircase input show repeatable performance, and the sinusoidal input shows a small amount of hysteresis consistent with viscoelastic response to pneumatic actuation of soft actuators. Simulated and real-world bending angles show comparable response. These methods provide a repeatable and robust fabrication procedure, validated across two operators and 24 successful fabrications, along with benchmark simulations and experimental testing. These benchmarks will enable more widespread adoption of soft robotics.

cs.RO↗