arXiv subjects

N. Blaskovic Kraljevic

Publications and source records attributed to N. Blaskovic Kraljevic.

12 recordsLinked to original sources

arXiv2024

The Development of Low-Q Cavity Type Beam Position Monitor with a Position Resolution of Nanometer for Future Colliders

The nano-meter beam size in future linear colliders requires very high resolution beam position monitor since higher resolution allows more accurate position measurement in the interaction point. We developed and tested a low-Q C-band beam position monitor with position resolution of nanometer. The C-band BPM was tested for the fast beam feedback system at the interaction point of ATF2 in KEK, in which C-band beam position monitor is called to IPBPM (Interaction Point Beam Position Monitor). The average position resolution of the developed IPBPMs was measured to be 10.1 nm at a nominal beam charge of $87\%$ of ATF2. From the measured beam position resolution, we can expect beam position resolution of around 8.8 nm and 4.4 nm with nominal ATF2 and ILC beam charge conditions, respectively, in which the position resolution is below the vertical beam size in ILC. In this paper, we describe the development of the IPBPM and the beam test results at the nanometer level in beam position resolution

physics.acc-ph↗

arXiv2024

Particle Physics at the European Spallation Source

Presently under construction in Lund, Sweden, the European Spallation Source (ESS) will be the world's brightest neutron source. As such, it has the potential for a particle physics program with a unique reach and which is complementary to that available at other facilities. This paper describes proposed particle physics activities for the ESS. These encompass the exploitation of both the neutrons and neutrinos produced at the ESS for high precision (sensitivity) measurements (searches).

physics.ins-det↗

arXiv2023

The ESSnuSB design study: overview and future prospects

ESSnuSB is a design study for an experiment to measure the CP violation in the leptonic sector at the second neutrino oscillation maximum using a neutrino beam driven by the uniquely powerful ESS linear accelerator. The reduced impact of systematic errors on sensitivity at the second maximum allows for a very precise measurement of the CP violating parameter. This review describes the fundamental advantages of measurement at the 2nd maximum, the necessary upgrades to the ESS linac in order to produce a neutrino beam, the near and far detector complexes, the expected physics reach of the proposed ESSnuSB experiment, concluding with the near future developments aimed at the project realization.

hep-ex↗

arXiv2022

The European Spallation Source neutrino Super Beam Conceptual Design Report

This conceptual design report provides a detailed account of the European Spallation Source neutrino Super Beam (ESS$ν$SB) feasibility study. This facility has been proposed after the measurements reported in 2012 of a relatively large value of the neutrino mixing angle $θ_{13}$, which raised the possibility of observing potential CP violation in the leptonic sector with conventional neutrino beams. The measured value of $θ_{13}$ also privileges the $2^{nd}$ oscillation maximum for the discovery of CP violation instead of the more typically studied $1^{st}$ maximum. The sensitivity at this $2^{nd}$ oscillation maximum is about three times higher than at the $1^{st}$ one, which implies a reduced influence of systematic errors. Working at the $2^{nd}$ oscillation maximum requires a very intense neutrino beam with an appropriate energy. The world's most intense pulsed spallation neutron source, the European Spallation Source (ESS), will have a proton linac operating at 5\,MW power, 2\,GeV kinetic energy and 14~Hz repetition rate (3~ms pulse duration, 4\% duty cycle) for neutron production. In this design study it is proposed to double the repetition rate and compress the beam pulses to the level of microseconds in order to provide an additional 5~MW proton beam for neutrino production. The physics performance has been evaluated for such a neutrino super beam, in conjunction with a megaton-scale underground water Cherenkov neutrino detector installed at a distance of 360--550\,km from ESS. The ESS proton linac upgrades, the accumulator ring required for proton-pulse compression, the target station design and optimisation, the near and far detector complexes, and the physics potential of the facility are all described in this report. The ESS linac will be operational by 2025, at which point the implementation of upgrades for the neutrino facility could begin.

hep-ex↗

arXiv2022

The European Spallation Source neutrino Super Beam

In this Snowmass 2021 white paper, we summarise the Conceptual Design of the European Spallation Source neutrino Super Beam (ESSvSB) experiment and its synergies with the possible future muon based facilities, e.g. a Low Energy nuSTORM and the Muon Collider. The ESSvSB will benefit from the high power, 5 MW, of the European Spallation Source (ESS) LINAC in Lund-Sweden to produce the world most intense neutrino beam, enabling measurements to be made at the second oscillation maximum. Assuming a ten-year exposure, physics simulations show that the CP-invariance violation can be established with a significance of 5 sigma over more than 70% of all values of delta CP and with an error in the measurement of the delta CP angle of less than 8 degree for all values of delta CP. However, several technological and physics challenges must be further studied before achieving a final Technical Design. Measuring at the 2nd oscillation maximum necessitates a very intense neutrino beam with the appropriate energy. For this, the ESS proton beam LINAC, which is designed to produce the world's most intense neutron beam, will need to be upgraded to 10 MW power, 2.5 GeV energy and 28 Hz beam pulse repetition rate. An accumulator ring will be required for the compression of the ESS LINAC beam pulse from 2.86 ms to 1.3 mus. A high power target station facility will be needed to produce a well-focused intense (super) mu-neutrino beam. The physics performance of that neutrino Super Beam in conjunction with a megaton underground Water Cherenkov neutrino far detector installed at a distance of either 360 km or 540 km from the ESS, the baseline, has been evaluated.

physics.acc-ph↗

arXiv2022

A high-resolution, low-latency, bunch-by-bunch feedback system for nano-beam stabilization

We report the design, operation and performance of a high-resolution, low-latency, bunch-by-bunch feedback system for nano-beam stabilisation. The system employs novel, ultra-low quality-factor cavity beam position monitors (BPMs), a two-stage analogue signal down-mixing system, and a digital signal processing and feedback board incorporating an FPGA. The FPGA firmware allows for the real-time integration of up to fifteen samples of the BPM waveforms within a measured latency of 232 ns. We show that this real-time sample integration improves significantly the beam position resolution and, consequently, the feedback performance. The best demonstrated real-time beam position resolution was 19 nm, which, as far as we are aware, is the best real-time resolution achieved in any operating BPM system. The feedback was operated in two complementary modes to stabilise the vertical position of the ultra-small beam produced at the focal point of the ATF2 beamline at KEK. In single-BPM feedback mode, beam stabilisation to 50$\pm$5 nm was demonstrated. In two-BPM feedback mode, beam stabilisation to 41$\pm$4 nm was achieved.

physics.acc-ph↗

arXiv2021

Updated physics performance of the ESSnuSB experiment

In this paper, we present the physics performance of the ESSnuSB experiment in the standard three flavor scenario using the updated neutrino flux calculated specifically for the ESSnuSB configuration and updated migration matrices for the far detector. Taking conservative systematic uncertainties corresponding to a normalization error of $5\%$ for signal and $10\%$ for background, we find that there is $10σ$ $(13σ)$ CP violation discovery sensitivity for the baseline option of 540 km (360 km) at $δ_{\rm CP} = \pm 90^\circ$. The corresponding fraction of $δ_{\rm CP}$ for which CP violation can be discovered at more than $5 σ$ is $70\%$. Regarding CP precision measurements, the $1σ$ error associated with $δ_{\rm CP} = 0^\circ$ is around $5^\circ$ and with $δ_{\rm CP} = -90^\circ$ is around $14^\circ$ $(7^\circ)$ for the baseline option of 540 km (360 km). For hierarchy sensitivity, one can have $3σ$ sensitivity for 540 km baseline except $δ_{\rm CP} = \pm 90^\circ$ and $5σ$ sensitivity for 360 km baseline for all values of $δ_{\rm CP}$. The octant of $θ_{23}$ can be determined at $3 σ$ for the values of: $θ_{23} > 51^\circ$ ($θ_{23} < 42^\circ$ and $θ_{23} > 49^\circ$) for baseline of 540 km (360 km). Regarding measurement precision of the atmospheric mixing parameters, the allowed values at $3 σ$ are: $40^\circ < θ_{23} < 52^\circ$ ($42^\circ < θ_{23} < 51.5^\circ$) and $2.485 \times 10^{-3}$ eV$^2 < Δm^2_{31} < 2.545 \times 10^{-3}$ eV$^2$ ($2.49 \times 10^{-3}$ eV$^2 < Δm^2_{31} < 2.54 \times 10^{-3}$ eV$^2$) for the baseline of 540 km (360 km).

hep-ex↗

arXiv2021

Stripping Mechanisms and Remediation for H$^-$ Beams

Negative hydrogen ions are often used for injecting protons from linacs to storage rings via charge-exchange injection. In this process, the two electrons are stripped by a foil or laser to produce protons which can be merged with an existing beam without significantly affecting its dynamics, allowing high intensities of protons to be accumulated. However, this capability comes with the drawback that the outer electron of an H$^-$ ion has a low binding energy and can easily be stripped away prior to injection. This paper addresses the following stripping mechanisms: interactions with residual gas in the beam pipe, blackbody radiation from accelerator components, and electromagnetic fields from accelerator optics (Lorentz-force stripping) and particles within the bunch itself (intrabeam stripping); with a discussion on how to avoid excessive activation from stripped H$^0$ particles and protons. We also demonstrate that the proportion of stripped H$^0$ colliding with a nearby beam pipe or machine-element walls presents only roughly 10\% of those lost in stripping; the remaining stripped particles traverse to the end of a linac or local straight section, which may relax the limits for allowable stripping-based beam loss in H$^-$ accelerators.

physics.acc-ph↗

arXiv2020

Measurements of sub-nT dynamic magnetic field shielding with soft iron and mu-metal for use in linear colliders

There is an increasing need to shield beams and accelerator elements from stray magnetic fields. The application of magnetic shielding in linear colliders is discussed. The shielding performance of soft iron and mu-metal is measured for magnetic fields of varying amplitude and frequency. Special attention is given to characterise the shielding performance for very small-amplitude magnetic fields.

physics.acc-ph↗

arXiv2020

Measurements and modelling of stray magnetic fields and the simulation of their impact on the Compact Linear Collider at 380 GeV

The Compact Linear Collider (CLIC) targets a nanometre beam size at the collision point. Realising this beam size requires the generation and transport of ultra-low emittance beams. Dynamic imperfections can deflect the colliding beams, leading to a collision with a relative offset. They can also degrade the emittance of each beam. Both of these effects can significantly impact the luminosity of CLIC. In this paper, we examine a newly considered dynamic imperfection: stray magnetic fields. Measurements of stray magnetic fields in the Large Hadron Collider tunnel are presented and used to develop a statistical model that can be used to realistically generate stray magnetic fields in simulations. The model is used in integrated simulations of CLIC at 380GeV including mitigation systems for stray magnetic fields to evaluate their impact on luminosity.

physics.acc-ph↗

arXiv2020

Luminosity Performance of the Compact Linear Collider at 380 GeV with Static and Dynamic Imperfections

The Compact Linear Collider is one of the two main European options for a collider in a post Large Hadron Collider era. This is a linear $e^+e^-$ collider with three centre-of-mass energy stages: 380 GeV, 1.5 TeV and 3 TeV. The luminosity performance of the first stage at 380 GeV is presented including the impact of static and dynamic imperfections. These calculations are performed with fully realistic tracking simulations from the exit of the damping rings to the interaction point and including beam-beam effects in the collisions. A luminosity of $4.3\times10^{34}\,\text{cm}^{-2}\text{s}^{-1}$ can be achieved with a perfect collider, which is almost three times the nominal luminosity target of $1.5\times10^{34}\,\text{cm}^{-2}\text{s}^{-1}$. In simulations with static imperfections, a luminosity of $2.35\times10^{34}\,\text{cm}^{-2}\text{s}^{-1}$ or greater is achieved by 90% of randomly misaligned colliders. Expressed as a percentage of the nominal luminosity target, this is a surplus of approximately 57%. Including the impact of ground motion, a luminosity surplus of 53% or greater can be expected for 90% of colliders. The average expected luminosity is $2.8\times10^{34}~\text{cm}^{-2}\text{s}^{-1}$, which is almost twice the nominal luminosity target.

physics.acc-ph↗

arXiv2018

Design and operation of a prototype interaction point beam collision feedback system for the International Linear Collider

A high-resolution, intratrain position feedback system has been developed to achieve and maintain collisions at the proposed future electron-positron International Linear Collider (ILC). A prototype has been commissioned and tested with a beam in the extraction line of the Accelerator Test Facility at the High Energy Accelerator Research Organization in Japan. It consists of a stripline beam position monitor (BPM) with analogue signal-processing electronics, a custom digital board to perform the feedback calculation, and a stripline kicker driven by a high-current amplifier. The closed-loop feedback latency is 148 ns. For a three-bunch train with 154 ns bunch spacing, the feedback system has been used to stabilize the third bunch to 450 nm. The kicker response is linear, and the feedback performance is maintained, over a correction range of over $\pm$60 μm. The propagation of the correction has been confirmed by using an independent stripline BPM located downstream of the feedback system. The system has been demonstrated to meet the BPM resolution, beam kick, and latency requirements for the ILC.

physics.acc-ph↗