arXiv subjects

N. Demos

Publications and source records attributed to N. Demos.

7 recordsLinked to original sources

arXiv2026

LIGO Detector Characterization in the Second and Third Parts of the Fourth Observing Run

LIGO detector characterization efforts enabled the confident detection of gravitational waves from hundreds of compact binary coalescences during the fourth observing run. Reliable production of high quality detector data and rapid noise mitigation efforts allow the extraction of the most in-depth knowledge of gravitational wave sources and their progenitors. In this paper we describe LIGO detector characterization activities during the second and third parts of O4-O4b and O4c. We summarize changes in detector configuration and performance at the LIGO Hanford and LIGO Livingston Observatories between the end of the first part of O4a and the end of O4c, including upgrades made during the commissioning break preceding O4b and during repairs performed in O4c. We describe instrumental investigations carried out at both sites designed to understand and subsequently mitigate the effect on detector sensitivity of transient glitches, narrowband spectral lines, and vibration-driven noise, among other data quality concerns. We then review the tools and procedures used to validate gravitational wave candidates and the data quality products thus supplied to searches for gravitational waves from compact binary coalescences and unmodeled transients, continuous gravitational waves, and the stochastic gravitational wave background. The efforts of the detector characterization group are essential for maintaining and improving the sensitivity and reliability of the LIGO detectors especially as observing runs lengthen and more events are detected. We conclude with prospects for LIGO detector characterization activities in future observing runs.

astro-ph.IM↗

arXiv2026

Experimental Realization of Optimized Ternary Mirror Coatings

We report on the first experimental realization of multi-material dielectric mirror coatings designed through a multi-objective optimization algorithm to simultaneously minimize thermal noise and optical losses. We validate this design strategy by fabricating and characterizing two distinct ternary systems: a SiNx -based proof-of-concept and a Ti:GeO2 -based system targeting lower optical losses. The performance of the SiN x coating shows remarkable agreement with predictions, demonstrating a noise amplitude spectral density reduction of 0.82 with respect to current reference coatings, and validating our design-to-fabrication pipeline. The Ti:GeO2 -based system achieves the crucial goal of sub-ppm absorption; its measured thermal noise, however, is higher than the theoretically predicted level of 0.71, extrapolated from single-layer material characterization. A dedicated tolerance analysis confirms that this discrepancy is not attributable to random thickness errors, emphasizing that further studies of the manufacturing process are needed to fully exploit this combination of materials. This work establishes a robust methodology for producing complex, high-performance optical coatings tailored for precision experiments.

physics.optics↗

arXiv2025

Low thermal noise mirror coatings utilising titanium dioxide and germanium dioxide mixtures

Upgrades to ground-based gravitational-wave observatories will require mirror coatings with reduced thermal noise, enabling improved detector sensitivity and extended astrophysical reach. Recent studies have shown that optical coatings utilising amorphous materials that exhibit a larger fraction of corner-sharing between adjacent structural units of metal-centered polyhedra are a promising route for reducing mechanical dissipation and thus thermal noise at room temperature. We report on multilayer optical coatings that are fabricated using germanium dioxide mixed with titanium dioxide (TiO$_2$:GeO$_2$) for the high index layers, and silicon dioxide (SiO$_2$) for the low index material. Single layers of TiO$_2$:GeO$_2$ are characterised to optimise the mixture proportion and based on that highly reflective multilayer stacks were deposited. Exceptional optical absorption at 1064 nm below 1 part-per-million (ppm) is observed in the multilayer stacks after heat treatment. The annealing process also induces the formation of blisters which leads to increased optical scattering. However, there is indication that blisters can be suppressed by decreasing the water partial pressure in the deposition chamber. Direct thermal noise measurements provide experimental verification of a significant 25\% reduction of thermal noise over the mirrors currently employed, which combined with sub-ppm levels of optical absorption show the potential of TiO$_2$:GeO$_2$ to improve the sensitivity of gravitational-wave observatories.

physics.ins-det↗

arXiv2024

Advanced LIGO detector performance in the fourth observing run

On May 24th, 2023, the Advanced Laser Interferometer Gravitational-Wave Observatory (LIGO), joined by the Advanced Virgo and KAGRA detectors, began the fourth observing run for a two-year-long dedicated search for gravitational waves. The LIGO Hanford and Livingston detectors have achieved an unprecedented sensitivity to gravitational waves, with an angle-averaged median range to binary neutron star mergers of 152 Mpc and 160 Mpc, and duty cycles of 65.0% and 71.2%, respectively, with a coincident duty cycle of 52.6%. The maximum range achieved by the LIGO Hanford detector is 165 Mpc and the LIGO Livingston detector 177 Mpc, both achieved during the second part of the fourth observing run. For the fourth run, the quantum-limited sensitivity of the detectors was increased significantly due to the higher intracavity power from laser system upgrades and replacement of core optics, and from the addition of a 300 m filter cavity to provide the squeezed light with a frequency-dependent squeezing angle, part of the A+ upgrade program. Altogether, the A+ upgrades led to reduced detector-wide losses for the squeezed vacuum states of light which, alongside the filter cavity, enabled broadband quantum noise reduction of up to 5.2 dB at the Hanford observatory and 6.1 dB at the Livingston observatory. Improvements to sensors and actuators as well as significant controls commissioning increased low frequency sensitivity. This paper details these instrumental upgrades, analyzes the noise sources that limit detector sensitivity, and describes the commissioning challenges of the fourth observing run.

gr-qc↗

arXiv2024

Development of ion-beam sputtered silicon nitride thin films for low-noise mirror coatings of gravitational-wave detectors

Brownian thermal noise of thin-film coatings is a fundamental limit for high-precision experiments based on optical resonators such as gravitational-wave interferometers. Here we present the results of a research activity aiming to develop lower-noise ion-beam sputtered silicon nitride thin films compliant with the very stringent requirements on optical loss of gravitational-wave interferometers. In order to test the hypothesis of a correlation between the synthesis conditions of the films and their elemental composition and optical and mechanical properties, we varied the voltage, current intensity and composition of the sputtering ion beam, and we performed a broad campaign of characterizations. While the refractive index was found to monotonically depend on the beam voltage and linearly vary with the N/Si ratio, the optical absorption appeared to be strongly sensitive to other factors, as yet unidentified. However, by systematically varying the deposition parameters, an optimal working point was found. Thus we show that the loss angle and extinction coefficient of our thin films can be as low as $(1.0 \pm 0.1) \times 10^{-4}$ rad at $\sim$2.8 kHz and $(6.4 \pm 0.2) \times 10^{-6}$ at 1064 nm, respectively, after thermal treatment at 900 $^{\circ}$C. To the best of our knowledge, such loss angle value is the lowest ever measured on this class of thin films. We then used our silicon nitride thin films to design and produce a multi-material mirror coating showing a thermal noise amplitude of $(10.3 \pm 0.2) \times 10^{-18}$ m Hz$^{-1/2}$ at 100 Hz, which is 25\% lower than in current mirror coatings of the Advanced LIGO and Advanced Virgo interferometers, and an optical absorption as low as $(1.6 \pm 0.5)$ parts per million at 1064 nm.

physics.ins-det↗

arXiv2024

LIGO Detector Characterization in the first half of the fourth Observing run

Progress in gravitational-wave astronomy depends upon having sensitive detectors with good data quality. Since the end of the LIGO-Virgo-KAGRA third Observing run in March 2020, detector-characterization efforts have lead to increased sensitivity of the detectors, swifter validation of gravitational-wave candidates and improved tools used for data-quality products. In this article, we discuss these efforts in detail and their impact on our ability to detect and study gravitational-waves. These include the multiple instrumental investigations that led to reduction in transient noise, along with the work to improve software tools used to examine the detectors data-quality. We end with a brief discussion on the role and requirements of detector characterization as the sensitivity of our detectors further improves in the future Observing runs.

astro-ph.IM↗

arXiv2021

Optical and mechanical properties of ion-beam-sputtered Nb$_2$O$_5$ and TiO$_2$-Nb$_2$O$_5$ thin films for gravitational-wave interferometers

Brownian thermal noise associated with highly-reflective mirror coatings is a fundamental limit for several precision experiments, including gravitational-wave detectors. Recently, there has been a worldwide effort to find mirror coatings with improved thermal noise properties that also fulfill strict optical requirements such as low absorption and scatter. We report on the optical and mechanical properties of ion-beam-sputtered niobia and titania-niobia thin films, and we discuss application of such coatings in current and future gravitational-wave detectors. We also report an updated direct coating thermal noise measurement of the HR coatings used in Advanced LIGO and Advanced Virgo.

physics.ins-det↗