Searcharxiv⌕ Search

arXiv subjects

N. N. Berendeev

Publications and source records attributed to N. N. Berendeev.

3 recordsLinked to original sources

Effect of superplastic deformation on the intergranular corrosion resistance of austenitic steel 321 with different types of UFG structure: A case of homogeneous and heterogeneous microstructure obtained by ECAP

The effects of superplasticity (SP) on the structure, hardness, and intergranular corrosion (IGC) resistance of UFG 321L steel are reported. By increasing the number of the ECAP cycles (N) and varying the ECAP temperature, and annealing temperature, the degree of the microstructural heterogeneity was changed. Regardless of the microstructural homogeneity degree, UFG steels demonstrated the possibility of realizing the SP effect at temperatures below the onset temperature of dynamic recrystallization. The dependence of ductility of the UFG steel on the test temperature is non-monotonic with a minimum at 450-600C. The maximum elongation to failure (~250%) was achieved at a SP temperature of 800C. The SP deformation of the UFG steel is controlled by the power law creep. It is shown that the hardness of UFG steel samples after SP is equal than the hardness of UFG steels annealed at the same temperature. It is also shown what SP leads to a decrease in the IGC resistance of the UFG steel. Heterostructured steel have reduced ductility, as well as lower resistance to IGC after tension tests at room temperature (RT). The minimum IGC resistance is ensured at N=2, and the maximum - at N=4. The IGC resistance of homogeneous UFG samples after tension testing exceeds the IGC resistance of coarse-grained steel. Tension test at a RT has the greatest negative effect on the IGC resistance of heterostructured steel, and the least negative effect on the IGC resistance of homogeneous steel. Increasing the number of ECAP cycles enhances the ductility of the UFG steel at 750-900C. Increasing the ECAP temperature results in a simultaneous decrease in ductility and flow stress. Heterostructured steel exhibits minimal values of the activation energy of SP deformation. Increasing the number of ECAP cycles and increasing the ECAP temperature lead to an increase in the activation energy of SP deformation.

cond-mat.mtrl-sci↗

Effect of annealing on the corrosion-fatigue strength and hot salt corrosion resistance of fine-grained titanium near-α alloy Ti-5Al-2V obtained by Rotary Swaging

The corrosion-fatigue strength in 3% aqueous NaCl solution and the resistance against hot salt corrosion (HSC) of the fine-grained near-a alloy Ti-5Al-2V (Russian analog of Grade 9 titanium alloy with increased aluminum content) has been studied. The properties of the Ti-5Al-2V alloy in the coarse-grained state, in the fine-grained after cold Rotary Swaging (RS), in partly recrystallized state, and in fully recrystallized one have been investigated. The mechanical properties of the alloy were characterized using compression tests and microhardness measurements. The effects of RS and of the annealing temperature and time on the character of corrosion destruction of the surface and on the composition of the products of the HSC were studied. RS was shown to result in an increase in the depth of the intergranular corrosion defects while the recrystallization annealing promotes the increasing of the corrosion resistance of the Ti-5Al-2V titanium alloy. The parameters of the Basquin equation for the corrosion-fatigue curves for the near-a Ti-5Al-2V alloy in the coarse-grained state, in the severely strained one, and after recrystallization annealing were determined for the first time. An effect of nonmonotonous dependencies of the slopes of the corrosion-fatigue curves for the strained near-a Ti-5Al-2V alloy on the recrystallization annealing temperature has been observed.

cond-mat.mtrl-sci↗

Corrosion fatigue crack initiation in ultrafine-grained near-a titanium alloy PT7M prepared by Rotary Swaging

The study focuses on corrosion fatigue processes taking place in an ultrafine-grained (UFG) near-a-titanium alloy Ti-2.5Al-2.6Zr (Russian industrial name PT7M) used in nuclear engineering. UFG structure formed with Rotary Swaging is found to increase resistance to corrosion fatigue. Parameters of the Basquin's equation are defined and the slope of the fatigue curve Sa-lg(N) is shown to depend (nonmonotonic dependence) on the UFG alloy annealing temperature. This effect can be explained with the patterns of microstructural evolution in a UFG alloy PT7M during annealing: (1) reduced density of lattice dislocations, (2) precipitation and dissolution of zirconium nanoparticles, (3) release of a''-phase particles causing internal stress fields along interphase (a-a'')-boundaries, and (4) intensive grain growth at elevated annealing temperatures. It is shown that the fatigue crack closure effect manifested as changing internal stress fields determined using XRD method may be observed in UFG titanium alloys.

cond-mat.mtrl-sci↗