arXiv subjects

N. Thomas

Publications and source records attributed to N. Thomas.

93 records · Page 6Linked to original sources

arXiv2008

The Balloon-borne Large Aperture Submillimeter Telescope: BLAST

The Balloon-borne Large Aperture Submillimeter Telescope (BLAST) is a sub-orbital surveying experiment designed to study the evolutionary history and processes of star formation in local galaxies (including the Milky Way) and galaxies at cosmological distances. The BLAST continuum camera, which consists of 270 detectors distributed between 3 arrays, observes simultaneously in broad-band (30%) spectral-windows at 250, 350, and 500 microns. The optical design is based on a 2m diameter telescope, providing a diffraction-limited resolution of 30" at 250 microns. The gondola pointing system enables raster mapping of arbitrary geometry, with a repeatable positional accuracy of ~30"; post-flight pointing reconstruction to ~5" rms is achieved. The on-board telescope control software permits autonomous execution of a pre-selected set of maps, with the option of manual override. In this paper we describe the primary characteristics and measured in-flight performance of BLAST. BLAST performed a test-flight in 2003 and has since made two scientifically productive long-duration balloon flights: a 100-hour flight from ESRANGE (Kiruna), Sweden to Victoria Island, northern Canada in June 2005; and a 250-hour, circumpolar-flight from McMurdo Station, Antarctica, in December 2006.

astro-ph↗

arXiv2004

Evidence of two effects in the size segregation process in a dry granular media

In a half-filled rotating drum, the size segregation of particles of equal density builds a ring pattern of the large particles, whose location continuously varies from the periphery to the center depending on the size ratio between particles [Thomas, Phys. Rev. E 62, 1 (2000) 961-974]. For small size ratios (typically15): large beads are close to the bottom in a reversing position. The existence of circles with an intermediate radius shows that the segregation at an intermediate level within a flow is possible. In this paper, we experimentally study the segregation of particles of different densities and sizes in a half-filled rotating drum and other devices (chute flow, pile). In the drum, the location of the segregated ring continuously varies from the periphery to the center and is very sensitive to both the size (from 1 to 33) and density (from 0.36 to 4.8) ratios. The densest large beads segregate on a circle close to the center, the lightest large beads on a circle close to the periphery. Consequently, we found that for any tracer, its excess of mass, due to only a size excess, a density excess, or both, leads to a deep inside segregation of the tracer. There is a push-away process that makes heavy beads of any type go downwards, while the excess of size is already known to push large beads towards the surface, by a dynamical sieving process. Each segregation at an intermediate ring corresponds to a balance between these mass and geometrical effects. The segregation level in the flow is determined by the ratio of the intensities of both effects.

cond-mat.other↗

arXiv2003

Monodisperse Dry Granular Flows on Inclined Planes : Role of Roughness

Recent studies have pointed out the importance of the basal friction on the dynamics of granular flows. We present experimental results on the influence of the roughness of the inclined plane on the dynamics of a monodisperse dry granular flow. We found experimentally that it exists a maximum of the friction for a given relative roughness. This maximum is shown to be independent of the angle of the slope. This behavior is observed for four planes with different bump sizes (given by the size of the beads glued on the plane) from 200 microns to 2 mm. The relative roughness corresponding to the maximum of the friction can be predicted with a geometrical model of stability of one single bead on the plane. The main parameters are the size of the bumps and the size of the flowing beads. In order to obtain a higher precision, the model also takes into account of the spacing between the bumps of the rough plane. Experimental results and model are in good agreement for all the planes we studied. Other parameters, like the sphericity of the beads, or irregularities in the thickness of the layer of glued particles, are shown to be of influence on the friction.

cond-mat.soft↗