arXiv subjects

Naidu Bezawada

Publications and source records attributed to Naidu Bezawada.

10 recordsLinked to original sources

arXiv2026

An Analysis of Large Astronomical Detector Controller Systems and Implications for Future ESO Detector Systems

Large astronomical instruments using tens to hundreds of optical or infrared science detectors pose specific challenges for detector control, where, in addition to performance, other engineering aspects like scalability, power consumption, size, weight and programmatic aspects such as cost and sustainability need to be considered. In this paper we analyze the approach existing instruments have taken for detector control. We focus this analysis on recent ground based astronomical instruments using 10 or more detectors for science imaging or spectrography. From this analysis we identify key technologies, like cryogenic electronics, Ethernet based interfaces and fully-digital detectors, for implementing efficient control of many detectors. We also propose a concept joining all identified technologies that could be considered for future large ESO instruments as a complement of ESO's general detector controller, NGCII.

astro-ph.IM↗

arXiv2020

Detector Systems Engineering for Extremely Large Instruments

The scientific detector systems for the ESO ELT first-light instruments, HARMONI, MICADO, and METIS, together will require 27 science detectors: seventeen 2.5 $μ$m cutoff H4RG-15 detectors, four 4K x 4K 231-84 CCDs, five 5.3 $μ$m cutoff H2RG detectors, and one 13.5 $μ$m cutoff GEOSNAP detector. This challenging program of scientific detector system development covers everything from designing and producing state-of-the-art detector control and readout electronics, to developing new detector characterization techniques in the lab, to performance modeling and final system verification. We report briefly on the current design of these detector systems and developments underway to meet the challenging scientific performance goals of the ELT instruments.

astro-ph.IM↗

arXiv2020

Characterisation, performance, and operational aspects of the H4RG-15 near infrared detectors for the MOONS instrument

MOONS is a multi-object spectrograph for the ESO VLT covering a simultaneous wavelength range of 0.6-1.8 microns using approximately 1000 fibres. It uses four Teledyne Imaging Systems H4RG-15 4K x 4K detectors with 2.5 $μ$m cut-off material for the two longer wavebands (YJ and H). Since the spectrographs utilize an extremely fast modified Schmidt camera design, then the detectors are situated in the optical beam and hence required the development of a novel 64- channel cryogenic differential cryogenic preamplifier, minimized for optical footprint which will be reported on. We have operated the Engineering Grade H4RG detector at a range of temperatures from 90K to 40K and we will report on the advantages of the lower operational temperature. We have completed a full persistence analysis and are able to model it reasonably well and will offer a correction for it in our data pipeline. We have also configured the detector for use with both unbuffered and buffered outputs and report on the differences in performance between the two output types. We have also seen some programming issues with the detector type and will report on our work-around for this, we will also describe the use of the column-deselect feature and row skipping to minimize the effects of PEDs. We have also measured charge injection per read and report on this, likewise we have also measured the inter-pixel capacitance in different regions of the detector. We will present all these results together with a summary of the complete performance characteristics of this detector family.

astro-ph.IM↗

arXiv2020

Performance advantages of buffered mode operation of HxRG near infrared detectors

The Teledyne HxRG detectors have versatile and programmable output options to allow operation of them in a variety of configurations such as slow unbuffered, slow buffered, fast buffered or unbuffered modes to optimise the detector performance for a given application. Normally at ESO, for low noise operation, the detectors are operated in slow unbuffered mode. Whilst the slow unbuffered mode offers a simple interface to the external preamplifier electronics, the detector operation in this mode can suffer from reduced pixel frequency response and higher electrical crosstalk between the readout channels. In the context of the detector systems required for the first generation instruments of the ELT (MICADO, HARMONI and METIS), an exercise was undertaken to evaluate the noise, speed and crosstalk performance of the detectors in the slow buffered mode. A test preamplifier has been designed with options to operate a H2RG detector in buffered or unbuffered and with or without using the reference output, so a direct performance comparison can be made between different modes. This paper presents the performance advantages such as increased pixel frequency response, elimination of electrical crosstalk between the readout channels and the noise performance in the buffered mode operation. These improvements allow us to achieve the same frame readout time using half the detector cryogenic electronics and detector controller electronics for the ELT instruments, which significantly reduces the associated cryomechanical complexities in the instrument.

astro-ph.IM↗

arXiv2020

HIRES, the high-resolution spectrograph for the ELT

HIRES will be the high-resolution spectrograph of the European Extremely Large Telescope at optical and near-infrared wavelengths. It consists of three fibre-fed spectrographs providing a wavelength coverage of 0.4-1.8 mic (goal 0.35-1.8 mic) at a spectral resolution of ~100,000. The fibre-feeding allows HIRES to have several, interchangeable observing modes including a SCAO module and a small diffraction-limited IFU in the NIR. Therefore, it will be able to operate both in seeing and diffraction-limited modes. ELT-HIRES has a wide range of science cases spanning nearly all areas of research in astrophysics and even fundamental physics. Some of the top science cases will be the detection of bio signatures from exoplanet atmospheres, finding the fingerprints of the first generation of stars (PopIII), tests on the stability of Nature's fundamental couplings, and the direct detection of the cosmic acceleration. The HIRES consortium is composed of more than 30 institutes from 14 countries, forming a team of more than 200 scientists and engineers.

astro-ph.IM↗

arXiv2020

Simulations and Design of a Single-Photon CMOS Imaging Pixel Using Multiple Non-Destructive Signal Sampling

A single-photon CMOS image sensor design based on pinned photodiode (PPD) with multiple charge transfers and sampling is described. In the proposed pixel architecture, the photogenerated signal is sampled non-destructively multiple times and the results are averaged. Each signal measurement is statistically independent and by averaging the electronic readout noise is reduced to a level where single photons can be distinguished reliably. A pixel design using this method has been simulated in TCAD and several layouts have been generated for a 180 nm CMOS image sensor process. Using simulations, the noise performance of the pixel has been determined as a function of the number of samples, sense node capacitance, sampling rate, and transistor characteristics. The strengths and the limitations of the proposed design are discussed in detail, including the trade-off between noise performance and readout rate and the impact of charge transfer inefficiency. The projected performance of our first prototype device indicates that single-photon imaging is within reach and could enable ground-breaking performance in many scientific and industrial imaging applications.

physics.ins-det↗

arXiv2018

The MICADO first light imager for the ELT: overview, operation, simulation

MICADO will enable the ELT to perform diffraction limited near-infrared observations at first light. The instrument's capabilities focus on imaging (including astrometric and high contrast) as well as single object spectroscopy. This contribution looks at how requirements from the observing modes have driven the instrument design and functionality. Using examples from specific science cases, and making use of the data simulation tool, an outline is presented of what we can expect the instrument to achieve.

astro-ph.IM↗

arXiv2018

First light with HiPERCAM on the GTC

HiPERCAM is a quintuple-beam imager that saw first light on the 4.2m William Herschel Telescope (WHT) in October 2017 and on the 10.4m Gran Telescopio Canarias (GTC) in February 2018. The instrument uses re-imaging optics and 4 dichroic beamsplitters to record ugriz (300-1000nm) images simultaneously on its five CCD cameras. The detectors in HiPERCAM are frame-transfer devices cooled thermo-electrically to -90degC, thereby allowing both long-exposure, deep imaging of faint targets, as well as high-speed (over 1000 windowed frames per second) imaging of rapidly varying targets. In this paper, we report on the as-built design of HiPERCAM, its first-light performance on the GTC, and some of the planned future enhancements.

astro-ph.IM↗

arXiv2015

The Visible and Infrared Survey Telescope for Astronomy (VISTA): Design, Technical Overview and Performance

The Visible and Infrared Survey Telescope for Astronomy (VISTA) is the 4-metre wide-field survey telescope at ESO's Paranal Observatory, equipped with the world's largest near-infrared imaging camera (VISTA IR Camera, VIRCAM), with 1.65 degree diameter field of view, and 67 Mpixels giving 0.6 square degrees active pixel area, operating at wavelengths 0.8 - 2.3 microns. We provide a short history of the project, and an overview of the technical details of the full system including the optical design, mirrors, telescope structure, IR camera, active optics, enclosure and software. The system includes several innovative design features such as the f/1 primary mirror, the dichroic cold-baffle camera design and the sophisticated wavefront sensing system delivering closed-loop 5-axis alignment of the secondary mirror. We conclude with a summary of the delivered performance, and a short overview of the six ESO public surveys in progress on VISTA.

astro-ph.IM↗

arXiv2012

Space-quality data from balloon-borne telescopes: the High Altitude Lensing Observatory (HALO)

We present a method for attaining sub-arcsecond pointing stability during sub- orbital balloon flights, as designed for in the High Altitude Lensing Observatory (HALO) concept. The pointing method presented here has the potential to perform near-space quality optical astronomical imaging at 1-2% of the cost of space-based missions. We also discuss an architecture that can achieve sufficient thermomechanical stability to match the pointing stability. This concept is motivated by advances in the development and testing of Ultra Long Duration Balloon (ULDB) flights which promise to allow observation campaigns lasting more than three months. The design incorporates a multi-stage pointing architecture comprising: a gondola coarse azimuth control system, a multi-axis nested gimbal frame structure with arcsecond stability, a telescope de-rotator to eliminate field rotation, and a fine guidance stage consisting of both a telescope mounted angular rate sensor and guide CCDs in the focal plane to drive a fast-steering mirror. We discuss the results of pointing tests together with a preliminary thermo-mechanical analysis required for sub-arcsecond pointing at high altitude. Possible future applications in the areas of wide-field surveys and exoplanet searches are also discussed.

astro-ph.IM↗