arXiv subjects

Nicolas Roch

Publications and source records attributed to Nicolas Roch.

At least 37 records · Page 2Linked to original sources

arXiv2023

Thermodynamics of a Single Mesoscopic Phononic Mode

In recent decades, the laws of thermodynamics have been pushed down to smaller and smaller scales, within the field of stochastic thermodynamics and state-of-art experiments performed on mesoscopic systems. These measurements concern electrons, photons, and mesoscopic mechanical objects. Here we report on the measurements of thermal fluctuations of a single mechanical mode in-equilibrium with a heat reservoir. The device under study is a nanomechanical beam with a first flexure resonating at 3.8MHz, cooled down to temperatures in the range from 100mK to 400mK. The technique is constructed around a microwave opto-mechanical setup using a cryogenic High Electron Mobility Transistor, and is based on two parametric amplifications implemented in series: an in-built opto-mechanical 'blue-detuned' pumping plus a Traveling Wave Parametric Amplifier stage. We demonstrate our ability to resolve energy fluctuations of the mechanical mode in real-time up to the fastest relevant speed given by the mechanical relaxation rate. The energy probability distribution is then exponential, matching the expected Boltzmann distribution. The variance of fluctuations is found to be $(k_B T)^2$ with no free parameters. Our microwave detection floor is about 3 Standard Quantum Limit at 6GHz; the resolution of our fastest acquisition tracks reached about 100 phonons, and is related to the rather poor opto-mechanical coupling of the device ($g_0/2π\approx 0.5~$Hz). This result is deeply in the classical regime, but shall be extended to the quantum case in the future with systems presenting a much larger $g_0$ (up to $2π\times 250~$Hz), potentially reaching the resolution of a single mechanical quantum. We believe that it will open a new experimental field: phonon-based quantum stochastic thermodynamics, with fundamental implications for quantum heat transport and macroscopic mechanical quantum coherence.

cond-mat.mes-hall↗

arXiv2022

Evidence of dual Shapiro steps in a Josephson junctions array

The modern primary voltage standard is based on the AC Josephson effect and the ensuing Shapiro steps, where a microwave tone applied to a Josephson junction yields a constant voltage $hf/2e$ ($h$ is Planck's constant and $e$ the electron charge) determined by only the microwave frequency $f$ and fundamental constants. Duality arguments for current and voltage have long suggested the possibility of dual Shapiro steps -- that a Josephson junction device could produce current steps with heights determined only on the applied frequency. In this report, we embed an ultrasmall Josephson junction in a high impedance array of larger junctions to reveal dual Shapiro steps. For multiple frequencies, we detect that the AC response of the circuit is synchronised with the microwave tone at frequency $f$, and the corresponding emergence of flat steps in the DC response with current $2ef$, equal to the tunnelling of a Cooper pair per tone period. This work sheds new light on phase-charge duality, omnipresent in condensed matter physics, and extends it to Josephson circuits. Looking forward, it opens a broad range of possibilities for new experiments in the field of circuit quantum electrodynamics and is an important step towards the long-sought closure of the quantum metrology electrical triangle.

cond-mat.mes-hall↗

arXiv2022

An Haloscope Amplification Chain based on a Travelling Wave Parametric Amplifier

In this paper we will describe the characterisation of a rf detection chain based on a travelling wave parametric amplifier (TWPA). The detection chain is meant to be used for dark matter axion searches and thus it is mounted coupled to a high Q microwave resonant cavity. A system noise temperature $T_{\rm sys} = (3.3 \pm 0.1$) K has been measured at a frequency of 10.77 GHz, using a novel scheme allowing measurement of $T_{\rm sys} $ exactly at the cavity output port.

physics.ins-det↗

arXiv2022

Kerr reversal in Josephson meta-material and traveling wave parametric amplification

Josephson meta-materials have recently emerged as very promising platform for superconducting quantum science and technologies. Their distinguishing potential resides in ability to engineer them at sub-wavelength scales, which allows complete control over wave dispersion and nonlinear interaction. In this article we report a versatile Josephson transmission line with strong third order nonlinearity which can be tuned from positive to negative values, and suppressed second order non linearity. As an initial implementation of this multipurpose meta-material, we operate it to demonstrate reversed Kerr phase-matching mechanism in traveling wave parametric amplification. Compared to previous state of the art phase matching approaches, this reversed Kerr phase matching avoids the presence of gaps in transmission, can reduce gain ripples, and allows in situ tunability of the amplification band over an unprecedented wide range. Besides such notable advancements in the amplification performance with direct applications to superconducting quantum computing and generation of broadband squeezing, the in-situ tunability with sign reversal of the nonlinearity in traveling wave structures, with no counterpart in optics to the best of our knowledge, opens exciting experimental possibilities in the general framework of microwave quantum optics, single-photon detection and quantum limited amplification.

quant-ph↗

arXiv2022

Observation of two-mode squeezing in a traveling wave parametric amplifier

Traveling wave parametric amplifiers (TWPAs) have recently emerged as essential tools for broadband near quantum-limited amplification. However, their use to generate microwave quantum states still misses an experimental demonstration. In this letter, we report operation of a TWPA as a source of two-mode squeezed microwave radiation. We demonstrate broadband entanglement generation between two modes separated by up to 400 MHz by measuring logarithmic negativity between 0.27 and 0.51 and collective quadrature squeezing below the vacuum limit between 1.5 and 2.1 dB. This work opens interesting perspectives for the exploration of novel microwave photonics experiments with possible applications in quantum sensing and continuous variable quantum computing.

quant-ph↗

arXiv2022

A gate-tunable graphene Josephson parametric amplifier

With a large portfolio of elemental quantum components, superconducting quantum circuits have contributed to dramatic advances in microwave quantum optics. Of these elements, quantum-limited parametric amplifiers have proven to be essential for low noise readout of quantum systems whose energy range is intrinsically low (tens of $μ$eV ). They are also used to generate non classical states of light that can be a resource for quantum enhanced detection. Superconducting parametric amplifiers, like quantum bits, typically utilize a Josephson junction as a source of magnetically tunable and dissipation-free nonlinearity. In recent years, efforts have been made to introduce semiconductor weak links as electrically tunable nonlinear elements, with demonstrations of microwave resonators and quantum bits using semiconductor nanowires, a two dimensional electron gas, carbon nanotubes and graphene. However, given the challenge of balancing nonlinearity, dissipation, participation, and energy scale, parametric amplifiers have not yet been implemented with a semiconductor weak link. Here we demonstrate a parametric amplifier leveraging a graphene Josephson junction and show that its working frequency is widely tunable with a gate voltage. We report gain exceeding 20 dB and noise performance close to the standard quantum limit. Our results complete the toolset for electrically tunable superconducting quantum circuits and offer new opportunities for the development of quantum technologies such as quantum computing, quantum sensing and fundamental science.

quant-ph↗

arXiv2021

Spin-boson quantum phase transition in multilevel superconducting qubits

Superconducting circuits are currently developed as a versatile platform for the exploration of many-body physics, by building on non-linear elements that are often idealized as two-level qubits. A classic example is given by a charge qubit that is capacitively coupled to a transmission line, which leads to the celebrated spin-boson description of quantum dissipation. We show that the intrinsic multilevel structure of superconducting qubits drastically restricts the validity of the spin-boson paradigm due to phase localization, which spreads the wavefunction over many charge states. Numerical Renormalization Group simulations also show that the quantum critical point moves out of the physically accessible range in the multilevel regime. Imposing charge discreteness in a simple variational state accounts for these multilevel effects, that are relevant for a large class of devices.

cond-mat.mes-hall↗

arXiv2021

The Grenoble Axion Haloscope platform (GrAHal): development plan and first results

In this note we report on the development plans and first results of the Grenoble Axion Haloscope (GrAHal) project. It is aimed at developing a haloscope platform dedicated to the search for axion dark matter particles. We discuss its general framework and the plans to reach the sensitivity required to probe well known invisible axion models, over particularly relevant axion masses and coupling regions. We also present our first haloscope prototype and the result of its test run at liquid He temperature, setting a new exclusion limit $g_{a γγ} \leq 2.2 \times 10^{-13}~ \text{GeV}^{-1}$ ($g_{a γγ} \leq 22 \times g_{\text{KSVZ}}$) around 6.375 GHz ($m_a \simeq 26.37$ $μ\text{eV}$).

hep-ex↗

arXiv2021

Perspective on traveling wave microwave parametric amplifiers

Quantum-limited microwave parametric amplifiers are genuine key pillars for rising quantum technologies and in general for applications that rely on the successful readout of weak microwave signals by adding only the minimum amount of noise allowed by quantum mechanics. In this perspective, after providing a brief overview on the different families of parametric microwave amplifiers, we focus on traveling wave parametric amplifiers (TWPAs), underlining the key achievements of the last years and the present open challenges. We discuss also possible new research directions beyond amplification such as exploring these devices as a platform for multi-mode entanglement generation and for the development of single photon detectors.

quant-ph↗

arXiv2021

A CMOS compatible platform for high impedance superconducting quantum circuits

Aluminium based platforms have allowed to reach major milestones for superconducting quantum circuits. For the next generation of devices, materials that are able to maintain low microwave losses while providing new functionalities, such as large kinetic inductance or compatibility with CMOS platform are sought for. Here we report on a combined direct current (DC) and microwave investigation of titanium nitride lms of dierent thicknesses grown using CMOS compatible methods. For microwave resonators made of TiN lm of thickness $\sim$3 nm, we measured large kinetic inductance LK $\sim$ 240 pH/sq, high mode impedance of $\sim$ 4.2 k$Ω$ while maintaining microwave quality factor $\sim$ 10^5 in the single photon limit. We present an in-depth study of the microwave loss mechanisms in these devices that indicates the importance of quasiparticles and provide insights for further improvement.

cond-mat.other↗

arXiv2020

Quantum non-demolition dispersive readout of a superconducting artificial atom using large photon numbers

Reading out the state of superconducting artificial atoms typically relies on dispersive coupling to a readout resonator. For a given system noise temperature, increasing the circulating photon number $\bar{n}$ in the resonator enables a shorter measurement time and is therefore expected to reduce readout errors caused by spontaneous atom transitions. However, increasing $\bar{n}$ is generally observed to also increase these transition rates. Here we present a fluxonium artificial atom in which we measure an overall flat dependence of the transition rates between its first two states as a function of $\bar{n}$, up to $\bar{n}\approx200$. Despite the fact that we observe the expected decrease of the dispersive shift with increasing readout power, the signal-to-noise ratio continuously improves with increasing $\bar{n}$. Even without the use of a parametric amplifier, at $\bar{n}=74$, we measure fidelities of 99% and 93% for feedback-assisted ground and excited state preparation, respectively.

quant-ph↗

arXiv2020

Minimizing the discrimination time for quantum states of an artificial atom

Fast discrimination between quantum states of superconducting artificial atoms is an important ingredient for quantum information processing. In circuit quantum electrodynamics, increasing the signal field amplitude in the readout resonator, dispersively coupled to the artificial atom, improves the signal-to-noise ratio and increases the measurement strength. Here we employ this effect over two orders of magnitude in readout power, made possible by the unique combination of a dimer Josephson junction array amplifier with a large dynamic range, and the fact that the readout of our granular aluminum fluxonium artificial atom remained quantum-non-demolition (QND) at relatively large photon numbers in the readout resonator, up to $\overline{n} = 110$. Using Bayesian inference, this allows us to detect quantum jumps faster than the readout resonator response time $2/κ$, where $κ$ is the bandwidth of the readout resonator.

quant-ph↗

arXiv2020

Highly transparent contacts to the 1D hole gas in ultra-scaled Ge/Si core/shell nanowires

Semiconductor-superconductor hybrid systems have outstanding potential for emerging high-performance nanoelectronics and quantum devices. However, critical to their successful application is the fabrication of high-quality and reproducible semiconductor-superconductor interfaces. Here, we realize and measure axial Al-Ge-Al nanowire heterostructures with atomically precise interfaces, enwrapped by an ultrathin epitaxial Si layer further denoted as Al-Ge/Si-Al nanowire heterostructures. The heterostructures were synthesized by a thermally induced exchange reaction of single-crystalline Ge/Si core/shell nanowires and lithographically defined Al contact pads. Applying this heterostructure formation scheme enables self-aligned quasi one-dimensional crystalline Al leads contacting ultrascaled Ge/Si segments with contact transparencies greater than 96%. Integration into back-gated field-effect devices and continuous scaling beyond lithographic limitations allows us to exploit the full potential of the highly transparent contacts to the 1D hole gas at the Ge-Si interface. This leads to the observation of ballistic transport as well as quantum confinement effects up to temperatures of 150 K. Low-temperature measurements reveal proximity-induced superconductivity in the Ge/Si core/shell nanowires. The realization of a Josephson field-effect transistor allows us to study the subgap structure caused by multiple Andreev reflections. Most importantly, the absence of a quantum dot regime indicates a hard superconducting gap originating from the highly transparent contacts to the 1D hole gas, which is potentially interesting for the study of Majorana zero modes. Moreover, underlining the importance of the proposed thermally induced Al-Ge/Si-Al heterostructure formation technique, our system could contribute to the development of key components of quantum computing such as gatemon or transmon qubits

cond-mat.mes-hall↗

arXiv2019

State preparation of a fluxonium qubit with feedback from a custom FPGA-based platform

We developed a versatile integrated control and readout instrument for experiments with superconducting quantum bits (qubits), based on a field-programmable gate array (FPGA) platform. Using this platform, we perform measurement-based, closed-loop feedback operations with $428 \, \mathrm{ns}$ platform latency. The feedback capability is instrumental in realizing active reset initialization of the qubit into the ground state in a time much shorter than its energy relaxation time $T_1$. We show experimental results demonstrating reset of a fluxonium qubit with $99.4\,\%$ fidelity, using a readout-and-drive pulse sequence approximately $1.5 \, \mathrm{μs}$ long. Compared to passive ground state initialization through thermalization, with the time constant given by $T_1 = ~ 80 \, \mathrm{μs}$, the use of the FPGA-based platform allows us to improve both the fidelity and the time of the qubit initialization by an order of magnitude.

quant-ph↗

arXiv2019

Observation of quantum many-body effects due to zero point fluctuations in superconducting circuits

Electromagnetic fields possess zero point fluctuations (ZPF) which lead to observable effects such as the Lamb shift and the Casimir effect. In the traditional quantum optics domain, these corrections remain perturbative due to the smallness of the fine structure constant. To provide a direct observation of non-perturbative effects driven by ZPF in an open quantum system we wire a highly non-linear Josephson junction to a high impedance transmission line, allowing large phase fluctuations across the junction. Consequently, the resonance of the former acquires a relative frequency shift that is orders of magnitude larger than for natural atoms. Detailed modelling confirms that this renormalization is non-linear and quantum. Remarkably, the junction transfers its non-linearity to about 30 environmental modes, a striking back-action effect that transcends the standard Caldeira-Leggett paradigm. This work opens many exciting prospects for longstanding quests such as the tailoring of many-body Hamiltonians in the strongly non-linear regime, the observation of Bloch oscillations, or the development of high-impedance qubits.

cond-mat.mes-hall↗

arXiv2019

A photonic crystal Josephson traveling wave parametric amplifier

An amplifier combining noise performances as close as possible to the quantum limit with large bandwidth and high saturation power is highly desirable for many solid state quantum technologies such as high fidelity qubit readout or high sensitivity electron spin resonance for example. Here we introduce a new Traveling Wave Parametric Amplifier based on Superconducting QUantum Interference Devices. It displays a 3 GHz bandwidth, a -102 dBm 1-dB compression point and added noise near the quantum limit. Compared to previous state-of-the-art, it is an order of magnitude more compact, its characteristic impedance is in-situ tunable and its fabrication process requires only two lithography steps. The key is the engineering of a gap in the dispersion relation of the transmission line. This is obtained using a periodic modulation of the SQUID size, similarly to what is done with photonic crystals. Moreover, we provide a new theoretical treatment to describe the non-trivial interplay between non-linearity and such periodicity. Our approach provides a path to co-integration with other quantum devices such as qubits given the low footprint and easy fabrication of our amplifier.

cond-mat.mes-hall↗

arXiv2019

Injection locking and parametric locking in a superconducting circuit

When a signal is injected in a parametric oscillator close enough to its resonance, the oscillator frequency and phase get locked to those of the injected signal. Here, we demonstrate two frequency locking schemes using a Josephson mixer in the parametric down-conversion regime, pumped beyond the parametric oscillation threshold. The circuit then emits radiation out of two spectraly and spatially separated resonators at frequencies determined by the locking schemes that we choose. When we inject the signal close to a resonance, it locks the oscillator emission to the signal frequency by injection locking. When we inject the signal close to the difference of resonances, it locks the oscillator emission by parametric locking. We compare both schemes and investigate the dependence of the parametric locking range on the pump and the injection signal power. Our results can be interpreted using Adler's theory for lasers, which makes a new link between laser physics and superconducting circuits that could enable better understanding of pumped circuits for quantum information applications such as error correction, circulators and photon number detectors.

cond-mat.mes-hall↗

arXiv2019

Fabrication and characterization of aluminum SQUID transmission lines

We report on the fabrication and characterization of 50 Ohms, flux-tunable, low-loss, SQUID-based transmission lines. The fabrication process relies on the deposition of a thin dielectric layer (few tens of nanometers) via Atomic Layer Deposition (ALD) on top of a SQUID array, the whole structure is then covered by a non-superconducting metallic top ground plane. We present experimental results from five different samples. We systematically characterize their microscopic parameters by measuring the propagating phase in these structures. We also investigate losses and discriminate conductor from dielectric losses. This fabrication method offers several advantages. First, the SQUID array fabrication does not rely on a Niobium tri-layer process but on a simpler double angle evaporation technique. Second, ALD provides high quality dielectric leading to low-loss devices. Further, the SQUID array fabrication is based on a standard, all-aluminum process, allowing direct integration with superconducting qubits. Moreover, our devices are in-situ flux tunable, allowing mitigation of incertitude inherent to any fabrication process. Finally, the unit cell being a single SQUID (no extra ground capacitance is needed), it is straightforward to modulate the size of the unit cell periodically, allowing band-engineering. This fabrication process can be directly applied to traveling wave parametric amplifiers.

cond-mat.mes-hall↗