arXiv subjects

Ningfeng Zhu

Publications and source records attributed to Ningfeng Zhu.

At least 19 recordsLinked to original sources

arXiv2022

Readout of a quantum processor with high dynamic range Josephson parametric amplifiers

We demonstrate a high dynamic range Josephson parametric amplifier (JPA) in which the active nonlinear element is implemented using an array of rf-SQUIDs. The device is matched to the 50 $\Omega$ environment with a Klopfenstein-taper impedance transformer and achieves a bandwidth of 250-300 MHz, with input saturation powers up to -95 dBm at 20 dB gain. A 54-qubit Sycamore processor was used to benchmark these devices, providing a calibration for readout power, an estimate of amplifier added noise, and a platform for comparison against standard impedance matched parametric amplifiers with a single dc-SQUID. We find that the high power rf-SQUID array design has no adverse effect on system noise, readout fidelity, or qubit dephasing, and we estimate an upper bound on amplifier added noise at 1.6 times the quantum limit. Lastly, amplifiers with this design show no degradation in readout fidelity due to gain compression, which can occur in multi-tone multiplexed readout with traditional JPAs.

quant-ph↗

arXiv2022

CCAT-prime: Design of the Mod-Cam receiver and 280 GHz MKID instrument module

Mod-Cam is a first light and commissioning instrument for the CCAT-prime project's six-meter aperture Fred Young Submillimeter Telescope (FYST), currently under construction at 5600 m on Cerro Chajnantor in Chile's Atacama Desert. Prime-Cam, a first-generation science instrument for FYST, will deliver over ten times greater mapping speed than current and near-term facilities for unprecedented 280-850 GHz broadband and spectroscopic measurements with microwave kinetic inductance detectors (MKIDs). CCAT-prime will address a suite of science goals, from Big Bang cosmology to star formation and galaxy evolution over cosmic time. Mod-Cam deployment on FYST with a 280 GHz instrument module containing MKID arrays is planned for early science observations in 2024. Mod-Cam will be used to test instrument modules for Prime-Cam, which can house up to seven instrument modules. We discuss the design and status of the 0.9 m diameter, 1.8 m long Mod-Cam receiver and 40 cm diameter 280 GHz instrument module, with cold stages at 40 K, 4 K, 1 K, and 100 mK. We also describe the instrument module's cryogenic readout designs to enable the readout of more than 10,000 MKIDs across 18 networks.

astro-ph.IM↗

arXiv2022

The Simons Observatory: Design and Measured Performance of a Carbon Fiber Strut for a Cryogenic Truss

We present the design and measured performance of a new carbon fiber strut design that is used in a cryogenically cooled truss for the Simons Observatory Small Aperture Telescope (SAT). The truss consists of two aluminum 6061 rings separated by 24 struts. Each strut consists of a central carbon fiber tube fitted with two aluminum end caps. We tested the performance of the strut and truss by (i) cryogenically cycling and destructively pull-testing strut samples, (ii) non-destructively pull-testing the final truss, and (iii) measuring the thermal conductivity of the carbon fiber tubes. We found that the strut strength is limited by the mounting fasteners and the strut end caps, not the epoxy adhesive or the carbon fiber tube. This result is consistent with our numerical predictions. Our thermal measurements suggest that the conductive heat load through the struts (from 4 K to 1 K) will be less than 1 mW. This strut design may be a promising candidate for use in other cryogenic support structures.

astro-ph.IM↗

arXiv2021

The 90 and 150 GHz universal focal-plane modules for the Simons Observatory

The Simons Observatory (SO) is a suite of telescopes located in the Atacama Desert in Chile that will make sensitive measurements of the cosmic microwave background. There are a host of cosmological and astrophysical questions that SO is forecasted to address. The universal focal-plane modules (UFMs) populate the four SO telescope receiver focal planes. There are three varieties of UFMs, each of which contains transition-edge-sensor bolometers observing in two spectral bands between 30 and 290~GHz. We describe the novel mid-frequency UFMs, which target two of the six spectral bands at 90 and 150~GHz and are central to the cosmological goals of SO.

astro-ph.IM↗

arXiv2021

The Simons Observatory: Galactic Science Goals and Forecasts

Observing in six frequency bands from 27 to 280 GHz over a large sky area, the Simons Observatory (SO) is poised to address many questions in Galactic astrophysics in addition to its principal cosmological goals. In this work, we provide quantitative forecasts on astrophysical parameters of interest for a range of Galactic science cases. We find that SO can: constrain the frequency spectrum of polarized dust emission at a level of $\Delta\beta_d \lesssim 0.01$ and thus test models of dust composition that predict that $\beta_d$ in polarization differs from that measured in total intensity; measure the correlation coefficient between polarized dust and synchrotron emission with a factor of two greater precision than current constraints; exclude the non-existence of exo-Oort clouds at roughly 2.9$\sigma$ if the true fraction is similar to the detection rate of giant planets; map more than 850 molecular clouds with at least 50 independent polarization measurements at 1 pc resolution; detect or place upper limits on the polarization fractions of CO(2-1) emission and anomalous microwave emission at the 0.1% level in select regions; and measure the correlation coefficient between optical starlight polarization and microwave polarized dust emission in $1^\circ$ patches for all lines of sight with $N_{\rm H} \gtrsim 2\times10^{20}$ cm$^{-2}$. The goals and forecasts outlined here provide a roadmap for other microwave polarization experiments to expand their scientific scope via Milky Way astrophysics.

astro-ph.GA↗

arXiv2021

The Simons Observatory: Constraining inflationary gravitational waves with multi-tracer B-mode delensing

We introduce and validate a delensing framework for the Simons Observatory (SO), which will be used to improve constraints on inflationary gravitational waves (IGWs) by reducing the lensing noise in measurements of the $B$-modes in CMB polarization. SO will initially observe CMB by using three small aperture telescopes and one large-aperture telescope. While polarization maps from small-aperture telescopes will be used to constrain IGWs, the internal CMB lensing maps used to delens will be reconstructed from data from the large-aperture telescope. Since lensing maps obtained from the SO data will be noise-dominated on sub-degree scales, the SO lensing framework constructs a template for lensing-induced $B$-modes by combining internal CMB lensing maps with maps of the cosmic infrared background from Planck as well as galaxy density maps from the LSST survey. We construct a likelihood for constraining the tensor-to-scalar ratio $r$ that contains auto- and cross-spectra between observed $B$-modes and the lensing $B$-mode template. We test our delensing analysis pipeline on map-based simulations containing survey non-idealities, but that, for this initial exploration, does not include contamination from Galactic and extragalactic foregrounds. We find that the SO survey masking and inhomogeneous and atmospheric noise have very little impact on the delensing performance, and the $r$ constraint becomes $\sigma(r)\approx 0.0015$ which is close to that obtained from the idealized forecasts in the absence of the Galactic foreground and is nearly a factor of two tighter than without delensing. We also find that uncertainties in the external large-scale structure tracers used in our multi-tracer delensing pipeline lead to bias much smaller than the $1\,\sigma$ statistical uncertainties.

astro-ph.CO↗

arXiv2021

The Simons Observatory: HoloSim-ML: machine learning applied to the efficient analysis of radio holography measurements of complex optical systems

Near-field radio holography is a common method for measuring and aligning mirror surfaces for millimeter and sub-millimeter telescopes. In instruments with more than a single mirror, degeneracies arise in the holography measurement, requiring multiple measurements and new fitting methods. We present HoloSim-ML, a Python code for beam simulation and analysis of radio holography data from complex optical systems. This code uses machine learning to efficiently determine the position of hundreds of mirror adjusters on multiple mirrors with few micron accuracy. We apply this approach to the example of the Simons Observatory 6m telescope.

astro-ph.IM↗

arXiv2021

The Simons Observatory microwave SQUID multiplexing detector module design

Advances in cosmic microwave background (CMB) science depend on increasing the number of sensitive detectors observing the sky. New instruments deploy large arrays of superconducting transition-edge sensor (TES) bolometers tiled densely into ever larger focal planes. High multiplexing factors reduce the thermal loading on the cryogenic receivers and simplify their design. We present the design of focal-plane modules with an order of magnitude higher multiplexing factor than has previously been achieved with TES bolometers. We focus on the novel cold readout component, which employs microwave SQUID multiplexing ($\mu$mux). Simons Observatory will use 49 modules containing 60,000 bolometers to make exquisitely sensitive measurements of the CMB. We validate the focal-plane module design, presenting measurements of the readout component with and without a prototype detector array of 1728 polarization-sensitive bolometers coupled to feedhorns. The readout component achieves a $95\%$ yield and a 910 multiplexing factor. The median white noise of each readout channel is 65 $\mathrm{pA/\sqrt{Hz}}$. This impacts the projected SO mapping speed by $< 8\%$, which is less than is assumed in the sensitivity projections. The results validate the full functionality of the module. We discuss the measured performance in the context of SO science requirements, which are exceeded.

astro-ph.IM↗

arXiv2021

Atacama Cosmology Telescope measurements of a large sample of candidates from the Massive and Distant Clusters of WISE Survey: Sunyaev-Zeldovich effect confirmation of MaDCoWS candidates using ACT

Galaxy clusters are an important tool for cosmology, and their detection and characterization are key goals for current and future surveys. Using data from the Wide-field Infrared Survey Explorer (WISE), the Massive and Distant Clusters of WISE Survey (MaDCoWS) located 2,839 significant galaxy overdensities at redshifts $0.7\lesssim z\lesssim 1.5$, which included extensive follow-up imaging from the Spitzer Space Telescope to determine cluster richnesses. Concurrently, the Atacama Cosmology Telescope (ACT) has produced large area mm-wave maps in three frequency bands along with a large catalog of Sunyaev-Zeldovich (SZ) selected clusters, as part of its Data Release 5 (DR5). Using the maps and cluster catalog from DR5, we explore the scaling between SZ mass and cluster richness. We use complementary radio survey data from the Very Large Array, submillimeter data from Herschel, and ACT 224~GHz data to assess the impact of contaminating sources on the SZ signals. We then use a hierarchical Bayesian model to fit the mass-richness scaling relation. We find that MaDCoWS clusters have submillimeter contamination which is consistent with a gray-body spectrum, while the ACT clusters are consistent with no submillimeter emission on average. We find the best fit ACT SZ mass vs. MaDCoWS richness scaling relation has a slope of $\kappa = 1.84^{+0.15}_{-0.14}$, where the slope is defined as $M\propto \lambda_{15}^{\kappa}$ where $\lambda_{15}$ is the richness. Additionally, we find that the approximate level of in-fill of the ACT and MaDCoWS cluster SZ signals to be at the percent level

astro-ph.GA↗

arXiv2021

The Simons Observatory: the Large Aperture Telescope (LAT)

The Simons Observatory (SO) is a Cosmic Microwave Background (CMB) experiment to observe the microwave sky in six frequency bands from 30GHz to 290GHz. The Observatory -- at $\sim$5200m altitude -- comprises three Small Aperture Telescopes (SATs) and one Large Aperture Telescope (LAT) at the Atacama Desert, Chile. This research note describes the design and current status of the LAT along with its future timeline.

astro-ph.IM↗

arXiv2021

The Simons Observatory Large Aperture Telescope Receiver

The Simons Observatory (SO) Large Aperture Telescope Receiver (LATR) will be coupled to the Large Aperture Telescope located at an elevation of 5,200 m on Cerro Toco in Chile. The resulting instrument will produce arcminute-resolution millimeter-wave maps of half the sky with unprecedented precision. The LATR is the largest cryogenic millimeter-wave camera built to date with a diameter of 2.4 m and a length of 2.6 m. It cools 1200 kg of material to 4 K and 200 kg to 100 mk, the operating temperature of the bolometric detectors with bands centered around 27, 39, 93, 145, 225, and 280 GHz. Ultimately, the LATR will accommodate 13 40 cm diameter optics tubes, each with three detector wafers and a total of 62,000 detectors. The LATR design must simultaneously maintain the optical alignment of the system, control stray light, provide cryogenic isolation, limit thermal gradients, and minimize the time to cool the system from room temperature to 100 mK. The interplay between these competing factors poses unique challenges. We discuss the trade studies involved with the design, the final optimization, the construction, and ultimate performance of the system.

astro-ph.IM↗

arXiv2021

The Integration and Testing Program for the Simons Observatory Large Aperture Telescope Optics Tubes

The Simons Observatory (SO) will be a cosmic microwave background (CMB) survey experiment with three small-aperture telescopes and one large-aperture telescope, which will observe from the Atacama Desert in Chile. In total, SO will field over 60,000 transition-edge sensor (TES) bolometers in six spectral bands centered between 27 and 280 GHz in order to achieve the sensitivity necessary to measure or constrain numerous cosmological quantities, as outlined in The Simons Observatory Collaboration et al. (2019). The 6~m Large Aperture Telescope (LAT), which will target the smaller angular scales of the CMB, utilizes a cryogenic receiver (LATR) designed to house up to 13 individual optics tubes. Each optics tube is comprised of three silicon lenses, IR blocking filters, and three dual-polarization, dichroic TES detector wafers. The scientific objectives of the SO project require these optics tubes to achieve high-throughput optical performance while maintaining exquisite control of systematic effects. We describe the integration and testing program for the SO LATR optics tubes that will verify the design and assembly of the optics tubes before they are shipped to the SO site and installed in the LATR cryostat. The program includes a quick turn-around test cryostat that is used to cool single optics tubes and validate the cryogenic performance and detector readout assembly. We discuss the optical design specifications the optics tubes must meet to be deployed on sky and the suite of optical test equipment that is prepared to measure these requirements.

astro-ph.IM↗

arXiv2021

Simons Observatory Small Aperture Telescope overview

The Simons Observatory (SO) is a cosmic microwave background (CMB) experiment from the Atacama Desert in Chile comprising three small-aperture telescopes (SATs) and one large-aperture telescope (LAT). In total, SO will field over 60,000 transition-edge sensor (TES) bolometers in six spectral bands centered between 27 and 280 GHz in order to achieve the sensitivity necessary to measure or constrain numerous cosmological quantities. In this work, we focus on the SATs which are optimized to search for primordial gravitational waves that are detected as parity-odd polarization patterns called a B-modes on degree scales in the CMB. Each SAT employs a single optics tube with TES arrays operating at 100 mK. The high throughput optics system has a 42 cm aperture and a 35-degree field of view coupled to a 36 cm diameter focal plane. The optics consist of three metamaterial anti-re ection coated silicon lenses. Cryogenic ring baffles with engineered blackbody absorbers are installed in the optics tube to minimize the stray light. The entire optics tube is cooled to 1 K. A cryogenic continuously rotating half-wave plate near the sky side of the aperture stop helps to minimize the effect of atmospheric uctuations. The telescope warm baffling consists of a forebaffle, an elevation stage mounted co-moving shield, and a fixed ground shield that together control the far side-lobes and mitigates ground-synchronous systematics. We present the status of the SAT development.

astro-ph.IM↗

arXiv2021

Design and Fabrication of Metamaterial Anti-Reflection Coatings for the Simons Observatory

astro-ph.IM↗

arXiv2020

The Simons Observatory: Overview of data acquisition, control, monitoring, and computer infrastructure

The Simons Observatory (SO) is an upcoming polarized cosmic microwave background (CMB) survey experiment with three small-aperture telescopes and one large-aperture telescope that will observe from the Atacama Desert in Chile. In total, SO will field over 60,000 transition-edge sensor (TES) bolometers in six spectral bands centered between 27 and 280 GHz to achieve the sensitivity necessary to measure or constrain numerous cosmological parameters, including the tensor-to-scalar ratio, effective number of relativistic species, and sum of the neutrino masses. The SO scientific goals require coordination and control of the hardware distributed among the four telescopes on site. To meet this need, we have designed and built an open-sourced platform for distributed system management, called the Observatory Control System (ocs). This control system interfaces with all subsystems including the telescope control units, the microwave multiplexing readout electronics, and the cryogenic thermometry. We have also developed a system for live monitoring of housekeeping data and alerting, both of which are critical for remote observation. We take advantage of existing open source projects, such as crossbar for RPC and PubSub, twisted for asynchronous events, grafana for online remote monitoring, and docker for containerization. We provide an overview of the SO software and computer infrastructure, including the integration of SO-developed code with open source resources and lessons learned while testing at SO labs developing hardware systems as we prepare for deployment.

astro-ph.IM↗

arXiv2020

The Simons Observatory: the Large Aperture Telescope Receiver (LATR) Integration and Validation Results

The Simons Observatory (SO) will observe the cosmic microwave background (CMB) from Cerro Toco in the Atacama Desert of Chile. The observatory consists of three 0.5 m Small Aperture Telescopes (SATs) and one 6 m Large Aperture Telescope (LAT), covering six frequency bands centering around 30, 40, 90, 150, 230, and 280 GHz. The SO observations will transform the understanding of our universe by characterizing the properties of the early universe, measuring the number of relativistic species and the mass of neutrinos, improving our understanding of galaxy evolution, and constraining the properties of cosmic reionization. As a critical instrument, the Large Aperture Telescope Receiver (LATR) is designed to cool $\sim$ 60,000 transition-edge sensors (TES) to $<$ 100 mK on a 1.7 m diameter focal plane. The unprecedented scale of the LATR drives a complex design. In this paper, we will first provide an overview of the LATR design. Integration and validation of the LATR design are discussed in detail, including mechanical strength, optical alignment, and cryogenic performance of the five cryogenic stages (80 K, 40 K, 4 K, 1 K, and 100 mK). We will also discuss the microwave-multiplexing ($\mu$Mux) readout system implemented in the LATR and demonstrate the operation of dark prototype TES bolometers. The $\mu$Mux readout technology enables one coaxial loop to read out $\mathcal{O}(10^3)$ TES detectors. Its implementation within the LATR serves as a critical validation for the complex RF chain design. The successful validation of the LATR performance is not only a critical milestone within the Simons Observatory, it also provides a valuable reference for other experiments, e.g. CCAT-prime and CMB-S4.

astro-ph.IM↗

arXiv2020

The Simons Observatory: Magnetic Sensitivity Measurements of Microwave SQUID Multiplexers

The Simons Observatory (SO) will be a cosmic microwave background (CMB) survey experiment with three small-aperture telescopes and one large-aperture telescope, which will observe from the Atacama Desert in Chile. In total, SO will field $\sim$70,000 transition-edge sensor (TES) bolometers in six spectral bands centered between 27 and 280 GHz in order to achieve the sensitivity necessary to measure or constrain numerous cosmological quantities. The SO Universal Focal Plane Modules (UFMs) each contain a 150 mm diameter TES detector array, horn or lenslet optical coupling, cold readout components, and magnetic shielding. SO will use a microwave SQUID multiplexing ($\mu$MUX) readout at an initial multiplexing factor of $\sim$1000; the cold (100 mK) readout components are packaged in a $\mu$MUX readout module, which is part of the UFM, and can also be characterized independently. The 100 mK stage TES bolometer arrays and microwave SQUIDs are sensitive to magnetic fields, and their measured response will vary with the degree to which they are magnetically shielded. We present measurements of the magnetic pickup of test microwave SQUID multiplexers as a study of various shielding configurations for the Simons Observatory. We discuss how these measurements motivated the material choice and design of the UFM magnetic shielding.

astro-ph.IM↗

arXiv2020

The Simons Observatory: Metamaterial Microwave Absorber (MMA) and its Cryogenic Applications

Controlling stray light at millimeter wavelengths requires special optical design and selection of absorptive materials that should be compatible with cryogenic operating environments. While a wide selection of absorptive materials exists, these typically exhibit high indices of refraction and reflect/scatter a significant fraction of light before absorption. For many lower index materials such as commercial microwave absorbers, their applications in cryogenic environments are challenging. In this paper, we present a new tool to control stray light: metamaterial microwave absorber tiles. These tiles comprise an outer metamaterial layer that approximates a lossy gradient index anti-reflection coating. They are fabricated via injection molding commercially available carbon-loaded polyurethane (25\% by mass). The injection molding technology enables mass production at low cost. The design of these tiles is presented, along with thermal tests to 1 K. Room temperature optical measurements verify their control of reflectance to less than 1\% up to 65$\circ$ angles of incidence, and control of wide angle scattering below 0.01\%. The dielectric properties of the bulk carbon-loaded material used in the tiles is also measured at different temperatures, confirming that the material maintains similar dielectric properties down to 3 K.

astro-ph.IM↗