arXiv subjects

Ojas Kanhere

Publications and source records attributed to Ojas Kanhere.

16 recordsLinked to original sources

arXiv2025

ISAC Imaging by Channel State Information using Ray Tracing for Next Generation 6G

Integrated sensing and communications (ISAC) is emerging as a cornerstone technology for sixth generation (6G) wireless systems, unifying connectivity and environmental mapping through shared hardware, spectrum, and waveforms. The following paper presents an ISAC imaging framework utilizing channel state information (CSI) per-path components, transmitter (TX) positions, and receiver (RX) positions obtained from the calibrated NYURay ray tracer at 6.75 GHz in the upper mid-band. Our work shows how each resolvable multipath component can be extracted from CSI estimation and cast into an equivalent three-dimensional reflection point by fusing its angle and delay information, which is useful and challenging for multi-bounce reflections. The primary contribution of the paper is the two-segment reflection point optimization algorithm, which independently estimates the path lengths from the TX position and RX position to an equivalent reflection point (ERP) on the object surface, thus enabling precise geometric reconstruction. Subsequently, we aggregate the ERPs derived from multiple pairs of TX and RX positions, generating dense three dimensional point clouds representing the objects in the channel. Experimental results validate that the proposed ISAC imaging framework accurately reconstructs object surfaces, edges, and curved features. To the best of our knowledge, this paper provides the first demonstration of multi bounce ISAC imaging using wireless ray tracing at 6.75 GHz.

eess.SP↗

arXiv2022

Sub-Terahertz Wireless Coverage Analysis at 142 GHz in Urban Microcell

Small-cell cellular base stations are going to be used for mmWave and sub-THz communication systems to provide multi-Gbps data rates and reliable coverage to mobile users. This paper analyzes the base station coverage of sub-THz communication systems and the system performance in terms of spectral efficiency through Monte Carlo simulations for both single-cell and multi-cell cases. The simulations are based on realistic channel models derived from outdoor field measurements at 142 GHz in urban microcell (UMi) environments conducted in downtown Brooklyn, New York. The single-cell base station can provide a downlink coverage area with a radius of 200 m and the 7-cell system can provide a downlink coverage area with a radius of 400 m at 142 GHz. Using a 1 GHz downlink bandwidth and 100 MHz uplink bandwidth, the 7-cell system can provide about 4.5 Gbps downlink average data rate and 410 Mbps uplink average data rate at 142 GHz.

cs.IT↗

arXiv2022

A Real-Time Millimeter Wave V2V Channel Sounder

Wireless communication in millimeter wave spectrum is poised to provide the latency and bandwidth needed for advanced use cases unfeasible at lower frequencies. Despite the market potential of vehicular communication networks, investigations into the millimeter wave vehicular channel are lacking. In this paper, we present a detailed overview of a novel 1 GHz wide, multi-antenna vehicle to vehicle directional channel sounding and measurement platform operating at 28 GHz. The channel sounder uses two 256-element phased arrays at the transmitter vehicle and four 64-element arrays at the receiver vehicle, with the receiver measuring 116 different directional beams in less than 1 millisecond. By measuring the full multi-beam channel impulse response at large bandwidths, our system provides unprecedented insight in instantaneous mobile vehicle to vehicle channels. The system also uses centimeter-level global position tracking and 360 degree video capture to provide additional contextual information for joint communication and sensing applications. An initial measurement campaign was conducted on highway and surface streets in Austin, Texas. We show example data that highlights the sensing capability of the system. Preliminary results from the measurement campaign show that bumper mounted mmWave arrays provide rich scattering in traffic as well a provide significant directional diversity aiding towards high reliability vehicular communication. Additionally, potential waveguide effects from high traffic in lanes can also extend the range of mmWave signals significantly.

cs.IT↗

arXiv2022

Sub-Terahertz Channel Measurements and Characterization in a Factory Building

Sub-Terahertz (THz) frequencies between 100 GHz and 300 GHz are being considered as a key enabler for the sixth-generation (6G) wireless communications due to the vast amounts of unused spectrum. The 3rd Generation Partnership Project (3GPP) included the indoor industrial environments as a scenario of interest since Release 15. This paper presents recent sub-THz channel measurements using directional horn antennas of 27 dBi gain at 142 GHz in a factory building, which hosts equipment manufacturing startups. Directional measurements with co-polarized and cross-polarized antenna configurations were conducted over distances from 6 to 40 meters. Omnidirectional and directional path loss with two antenna polarization configurations produce the gross cross-polarization discrimination (XPD) with a mean of 27.7 dB, which suggests that dual-polarized antenna arrays can provide good multiplexing gain for sub-THz wireless systems. The measured power delay profile and power angular spectrum show the maximum root mean square (RMS) delay spread of 66.0 nanoseconds and the maximum RMS angular spread of 103.7 degrees using a 30 dB threshold, indicating the factory scenario is a rich-scattering environment due to a massive number of metal structures and objects. This work will facilitate emerging sub-THz applications such as super-resolution sensing and positioning for future smart factories.

eess.SP↗

arXiv2021

Millimeter Wave and Sub-Terahertz Spatial Statistical Channel Model for an Indoor Office Building

Millimeter-wave (mmWave) and sub-Terahertz (THz) frequencies are expected to play a vital role in 6G wireless systems and beyond due to the vast available bandwidth of many tens of GHz. This paper presents an indoor 3-D spatial statistical channel model for mmWave and sub-THz frequencies based on extensive radio propagation measurements at 28 and 140 GHz conducted in an indoor office environment from 2014 to 2020. Omnidirectional and directional path loss models and channel statistics such as the number of time clusters, cluster delays, and cluster powers were derived from over 15,000 measured power delay profiles. The resulting channel statistics show that the number of time clusters follows a Poisson distribution and the number of subpaths within each cluster follows a composite exponential distribution for both LOS and NLOS environments at 28 and 140 GHz. This paper proposes a unified indoor statistical channel model for mmWave and sub-Terahertz frequencies following the mathematical framework of the previous outdoor NYUSIM channel models. A corresponding indoor channel simulator is developed, which can recreate 3-D omnidirectional, directional, and multiple input multiple output (MIMO) channels for arbitrary mmWave and sub-THz carrier frequency up to 150 GHz, signal bandwidth, and antenna beamwidth. The presented statistical channel model and simulator will guide future air-interface, beamforming, and transceiver designs for 6G and beyond.

cs.IT↗

arXiv2021

Outdoor sub-THz Position Location and Tracking using Field Measurements at 142 GHz

Future sub-THz cellular deployments may be utilized to complement the coverage of the global positioning system (GPS) and provide centimeter-level accuracy. In this work, we use measurement data at 142 GHz to test a map-based position location algorithm in an outdoor urban microcell (UMi) environment. We utilize an extended Kalman filter (EKF) to track the position of the user equipment (UE) along a rectangular track, with the transmitter-receiver separation distances varying from 24.3 m to 52.8 m. The position and velocity of the UE are tracked by the EKF, with measurements of the angle of arrival and time of flight information obtained along an outdoor track, to provide a mean accuracy of 24.8 cm at 142 GHz, over 34 UE locations, using a single base station in line-of-sight and non-line-of-sight.

cs.IT↗

arXiv2021

Position Location for Futuristic Cellular Communications -- 5G and Beyond

With vast mmWave spectrum and narrow beam antenna technology, precise position location is now possible in 5G and future mobile communication systems. In this article, we describe how centimeterlevel localization accuracy can be achieved, particularly through the use of map-based techniques. We show how data fusion of parallel information streams, machine learning, and cooperative localization techniques further improve positioning accuracy.

cs.IT↗

arXiv2020

3-D Statistical Indoor Channel Model for Millimeter-Wave and Sub-Terahertz Bands

Millimeter-wave (mmWave) and Terahertz (THz) will be used in the sixth-generation (6G) wireless systems, especially for indoor scenarios. This paper presents an indoor three-dimensional (3-D) statistical channel model for mmWave and sub-THz frequencies, which is developed from extensive channel propagation measurements conducted in an office building at 28 GHz and 140 GHz in 2014 and 2019. Over 15,000 power delay profiles (PDPs) were recorded to study channel statistics such as the number of time clusters, cluster delays, and cluster powers. All the parameters required in the channel generation procedure are derived from empirical measurement data for 28 GHz and 140 GHz line-of-sight (LOS) and non-line-of-sight (NLOS) scenarios. The channel model is validated by showing that the simulated root mean square (RMS) delay spread and RMS angular spread yield good agreements with measured values. An indoor channel simulation software is built upon the popular NYUSIM outdoor channel simulator, which can generate realistic channel impulse response, PDP, and power angular spectrum.

eess.SP↗

arXiv2020

Real-time Millimeter Wave Omnidirectional Channel Sounder Using Phased Array Antennas

Characterization of the millimeter wave wireless channel is needed to facilitate fully connected vehicular communication in the future. To study the multipath-rich, rapidly varying nature of the vehicular propagation environment, fast millimeter wave channel sounders are required. We present a channel sounder design capable of covering 360 degrees in azimuth and 60 degrees in elevation with 200 individual beam directions in 6.25 ms by using four phased arrays simultaneously. The channel measurements are accompanied by high resolution positioning and video data, allowing channel sounding to be conducted while either the transmitter, or the receiver, or both are moving. Channel sounding campaigns were conducted at multiple urban locations with light traffic conditions in Austin, Texas. Preliminary results show that beam selection at the receiver can lower the effective pathloss exponent to 1.6 for line-of-sight and 2.25 for non line-of-sight.

cs.IT↗

arXiv2020

Millimeter Wave Position Location using Multipath Differentiation for 3GPP using Field Measurements

3GPP air interface standards support meter-level position location of a user in a cellular network. With wider bandwidths and narrow antenna beamwidths available at mmWave frequencies, cellular networks now have the potential to provide sub-meter position location for each user. In this work, we provide an overview of 3GPP position location techniques that are designed for line-of-sight propagation. We discuss additional measurements required in the 3GPP standard that enable multipath-based non-line-of-sight position location. Further, we validate the concepts in this paper by using field data to test a map-based position location algorithm in an indoor office environment which has dimensions of 35 m by 65.5 m. We demonstrate how the fusion of angle of arrival and time of flight information in concert with a 3-D map of the office provides a mean accuracy of 5.72 cm at 28 GHz and 6.29 cm at 140 GHz, over 23 receiver distances ranging from 4.2 m to 32.3 m, using a single base station in line-of-sight and non-line-of-sight. We also conduct a theoretical analysis of the typical error experienced in the map-based position location algorithm and show that the complexity of the map-based algorithm is low enough to allow real-time implementation.

cs.IT↗

arXiv2019

Indoor Wireless Channel Properties at Millimeter Wave and Sub-Terahertz Frequencies

This paper provides indoor reflection, scattering, transmission, and large-scale path loss measurements and models, which describe the main propagation mechanisms at millimeter wave and Terahertz frequencies. Channel properties for common building materials (drywall and clear glass) are carefully studied at 28, 73, and 140 GHz using a wideband sliding correlation based channel sounder system with rotatable narrow-beam horn antennas. Reflection coefficient is shown to linearly increase as the incident angle increases, and lower reflection loss (e.g., stronger reflections) are observed as frequencies increase for a given incident angle. Although backscatter from drywall is present at 28, 73, and 140 GHz, smooth surfaces (like drywall) are shown to be modeled as a simple reflected surface, since the scattered power is 20 dB or more below the reflected power over the measured range of frequency and angles. Partition loss tends to increase with frequency, but the amount of loss is material dependent. Both clear glass and drywall are shown to induce a depolarizing effect, which becomes more prominent as frequency increases. Indoor propagation measurements and large-scale indoor path loss models at 140 GHz are provided, revealing similar path loss exponent and shadow fading as observed at 28 and 73 GHz. The measurements and models in this paper can be used for future wireless system design and other applications within buildings for frequencies above 100 GHz.

eess.SP↗

arXiv2019

A Millimeter-Wave Channel Simulator NYUSIM with Spatial Consistency and Human Blockage

Accurate channel modeling and simulation are indispensable for millimeter-wave wideband communication systems that employ electrically-steerable and narrow beam antenna arrays. Three important channel modeling components, spatial consistency, human blockage, and outdoor-to-indoor penetration loss, were proposed in the 3rd Generation Partnership Project Release 14 for mmWave communication system design. This paper presents NYUSIM 2.0, an improved channel simulator which can simulate spatially consistent channel realizations based on the existing drop-based channel simulator NYUSIM 1.6.1. A geometry-based approach using multiple reflection surfaces is proposed to generate spatially correlated and time-variant channel coefficients. Using results from 73 GHz pedestrian measurements for human blockage, a four-state Markov model has been implemented in NYUSIM to simulate dynamic human blockage shadowing loss. To model the excess path loss due to penetration into buildings, a parabolic model for outdoor-to-indoor penetration loss has been adopted from the 5G Channel Modeling special interest group and implemented in NYUSIM 2.0. This paper demonstrates how these new modeling capabilities reproduce realistic data when implemented in Monte Carlo fashion using NYUSIM 2.0, making it a valuable measurement-based channel simulator for fifth-generation and beyond mmWave communication system design and evaluation.

cs.IT↗

arXiv2019

Map-Assisted Millimeter Wave Localization for Accurate Position Location

Accurate precise positioning at millimeter wave frequencies is possible due to the large available bandwidth that permits precise on-the-fly time of flight measurements using conventional air interface standards. In addition, narrow antenna beamwidths may be used to determine the angles of arrival and departure of the multipath components between the base station and mobile users. By combining accurate temporal and angular information of multipath components with a 3-D map of the environment (that may be built by each user or downloaded a-priori), robust localization is possible, even in non-line-of-sight environments. In this work, we develop an accurate 3-D ray tracer for an indoor office environment and demonstrate how the fusion of angle of departure and time of flight information in concert with a 3-D map of a typical large office environment provides a mean accuracy of 12.6 cm in line-of-sight and 16.3 cm in non-line-of-sight, over 100 receiver distances ranging from 1.5 m to 24.5 m using a single base station. We show how increasing the number of base stations improves the average non-line-of-sight position location accuracy to 5.5 cm at 21 locations with a maximum propagation distance of 24.5 m.

cs.IT↗

arXiv2019

Scattering Mechanisms and Modeling for Terahertz Wireless Communications

This paper provides an analysis of radio wave scattering for frequencies ranging from the microwave to the Terahertz band (e.g., 1 GHz - 1 THz), by studying the scattering power reradiated from various types of materials with different surface roughnesses. First, fundamentals of scattering and reflection are developed and explained for use in wireless mobile radio, and the effect of scattering on the reflection coefficient for rough surfaces is investigated. Received power is derived using two popular scattering models - the directive scattering (DS) model and the radar cross section (RCS) model through simulations over a wide range of frequencies, materials, and orientations for the two models, and measurements confirm the accuracy of the DS model at 140 GHz. This paper shows that scattering can become a prominent propagation mechanism as frequencies extend to millimeter-wave (mmWave) and beyond, but at other times can be treated like simple reflection. Knowledge of scattering effects is critical for appropriate and realistic channel models, which further support the development of massive multiple input-multiple output (MIMO) techniques, localization, ray tracing tool design, and imaging for future 5G and 6G wireless systems.

eess.SP↗

arXiv2018

Position Locationing for Millimeter Wave Systems

The vast amount of spectrum available for millimeter wave (mmWave) wireless communication systems will support accurate real-time positioning concurrent with communication signaling. This paper demonstrates that accurate estimates of the position of an unknown node can be determined using estimates of time of arrival (ToA), angle of arrival (AoA), as well as data fusion or machine learning. Real-world data at 28 GHz and 73 GHz is used to show that AoA-based localization techniques will need to be augmented with other positioning techniques. The fusion of AoA-based positioning with received power measurements for RXs in an office which has dimensions of 35 m by 65.5 m is shown to provide location accuracies ranging from 16 cm to 3.25 m, indicating promise for accurate positioning capabilities in future networks. Received signal strength intensity (RSSI) based positioning techniques that exploit the ordering of the received power can be used to determine rough estimates of user position. Prediction of received signal characteristics is done using 2-D ray tracing.

cs.IT↗

arXiv2018

Verification and Calibration of Antenna Cross-Polarization Discrimination and Penetration Loss for Millimeter Wave Communications

This article presents measurement guidelines and verification procedures for antenna cross-polarization discrimination (XPD) and penetration loss measurements for millimeter wave (mmWave) channel sounder systems. These techniques are needed to ensure accurate and consistent measurements by different researchers at different frequencies and bandwidths. Measurements at 73 GHz are used to demonstrate and verify the guidelines, and show the consistency of the antenna XPD factor and the penetration loss at different transmitter-receiver (T-R) separation distances, thus providing a systematic method that may be used at any frequency for reliable field measurements.

cs.IT↗