arXiv subjects

Olga I. Vinogradova

Publications and source records attributed to Olga I. Vinogradova.

At least 55 records · Page 3Linked to original sources

arXiv2014

Disjoining Pressure of an Electrolyte Film Confined between Semipermeable Membranes

We consider an electrolyte solution confined by semipermeable membranes in contact with a salt-free solvent. Membranes are uncharged, but since small counter-ions leak-out into infinite salt-free reservoirs, we observe a distance-dependent membrane potential, which generates a repulsive electrostatic disjoining pressure. We obtain the distribution of the potential and of ions, and derive explicit formulas for the disjoining pressure, which are validated by computer simulations. We predict a strong short-range power-law repulsion, and a weaker long-range exponential decay. Our results also demonstrate that an interaction between membranes does strongly depend on the screening lengths, valency of an electrolyte solution, and an inter-membrane film thickness. Finally, our analysis can be directly extended to the study of more complex situations and some biological problems.

cond-mat.soft↗

arXiv2014

Contact Angle Hysteresis on Superhydrophobic Stripes

We study experimentally and discuss quantitatively the contact angle hysteresis on striped superhydrophobic surfaces as a function of a solid fraction, $ϕ_S$. It is shown that the receding regime is determined by a longitudinal sliding motion the deformed contact line. Despite an anisotropy of the texture the receding contact angle remains isotropic, i.e. is practically the same in the longitudinal and transverse directions. The cosine of the receding angle grows nonlinearly with $ϕ_S$, in contrast to predictions of the Cassie equation. To interpret this we develop a simple theoretical model, which shows that the value of the receding angle depends both on weak defects at smooth solid areas and on the elastic energy of strong defects at the borders of stripes, which scales as $ϕ_S^2 \ln ϕ_S$. The advancing contact angle was found to be anisotropic, except as in a dilute regime, and its value is determined by the rolling motion of the drop. The cosine of the longitudinal advancing angle depends linearly on $ϕ_S$, but a satisfactory fit to the data can only be provided if we generalize the Cassie equation to account for weak defects. The cosine of the transverse advancing angle is much smaller and is maximized at $ϕ_S\simeq 0.5$. An explanation of its value can be obtained if we invoke an additional energy due to strong defects in this direction, which is shown to be proportional to $ϕ_S^2$. Finally, the contact angle hysteresis is found to be quite large and generally anisotropic, but it becomes isotropic when $ϕ_S\leq 0.2$.

cond-mat.soft↗

arXiv2014

Lattice-Boltzmann simulations of the drag force on a sphere approaching a superhydrophobic striped plane

By means of lattice-Boltzmann simulations the drag force on a sphere of radius R approaching a superhydrophobic striped wall has been investigated as a function of arbitrary separation h. Superhydrophobic (perfect-slip vs. no-slip) stripes are characterized by a texture period L and a fraction of the gas area $ϕ$. For very large values of h/R we recover the macroscopic formulae for a sphere moving towards a hydrophilic no-slip plane. For h/R=O(1) and smaller the drag force is smaller than predicted by classical theories for hydrophilic no-slip surfaces, but larger than expected for a sphere interacting with a uniform perfectly slipping wall. At a thinner gap, $h\ll R$ the force reduction compared to a classical result becomes more pronounced, and is maximized by increasing $ϕ$. In the limit of very small separations our simulation data are in quantitative agreement with an asymptotic equation, which relates a correction to a force for superhydrophobic slip to texture parameters. In addition, we examine the flow and pressure field and observe their oscillatory character in the transverse direction in the vicinity of the wall, which reflects the influence of the heterogeneity and anisotropy of the striped texture. Finally, we investigate the lateral force on the sphere, which is detectable in case of very small separations and is maximized by stripes with $ϕ=0.5$.

physics.flu-dyn↗

arXiv2013

Effective slip-length tensor for a flow over weakly slipping stripes

We discuss the flow past a flat heterogeneous solid surface decorated by slipping stripes. The spatially varying slip length, $b(y)$, is assumed to be small compared to the scale of the heterogeneities, $L$, but finite. For such "weakly" slipping surfaces, earlier analyses have predicted that the effective slip length is simply given by the surface-averaged slip length, which implies that the effective slip-length tensor becomes isotropic. Here we show that a different scenario is expected if the local slip length has step-like jumps at the edges of slipping heterogeneities. In this case, the next-to-leading term in an expansion of the effective slip-length tensor in powers of ${max}\,(b(y)/L)$ becomes comparable to the leading-order term, but anisotropic, even at very small $b(y)/L$. This leads to an anisotropy of the effective slip, and to its significant reduction compared to the surface-averaged value. The asymptotic formulae are tested by numerical solutions and are in agreement with results of dissipative particle dynamics simulations.

physics.flu-dyn↗

arXiv2013

Effective slippage on superhydrophobic trapezoidal grooves

We study the effective slippage on superhydrophobic grooves with trapezoidal cross-sections of various geometries (including the limiting cases of triangles and rectangular stripes), by using two complementary approaches. First, dissipative particle dynamics (DPD) simulations of a flow past such surfaces have been performed to validate an expression [E.S.Asmolov and O.I.Vinogradova, J. Fluid Mech. \textbf{706}, 108 (2012)] that relates the eigenvalues of the effective slip-length tensor for one-dimensional textures. Second, we propose theoretical estimates for the effective slip length and calculate it numerically by solving the Stokes equation based on a collocation method. The comparison between the two approaches shows that they are in excellent agreement. Our results demonstrate that the effective slippage depends strongly on the area-averaged slip, the amplitude of the roughness, and on the fraction of solid in contact with the liquid. To interpret these results, we analyze flow singularities near slipping heterogeneities, and demonstrate that they inhibit the effective slip and enhance the anisotropy of the flow. Finally, we propose some guidelines to design optimal one-dimensional superhydrophobic surfaces, motivated by potential applications in microfluidics.

physics.flu-dyn↗

arXiv2013

Flow in channels with superhydrophobic trapezoidal textures

Superhydrophobic one-dimensional surfaces reduce drag and generate transverse hydrodynamic phenomena by combining hydrophobicity and roughness to trap gas bubbles in microscopic textures. Recent works in this area have focused on specific cases of superhydrophobic stripes. Here we provide some theoretical results to guide the optimization of the forward flow and transverse hydrodynamic phenomena in a parallel-plate channel with a superhydrophobic trapezoidal texture, varying on scales larger than the channel thickness. The permeability of such a thin channel is shown to be equivalent to that of a striped one with greater average slip. The maximization of a transverse flow normally requires largest possible slip at the gas areas, similarly to a striped channel. However, in case of trapezoidal textures with a very small fraction of the solid phase this maximum occurs at a finite slip at the gas areas. Exact numerical calculations show that our analysis, based on a lubrication theory, can also be applied for a larger gap. However, in this case it overestimates a permeability of the channel, and underestimates an anisotropy of the flow. Our results provide a framework for the rational design of superhydrophobic surfaces for microfluidic applications.

physics.flu-dyn↗

arXiv2013

Electrostatic Interaction of Heterogeneously Charged Surfaces with Semipermeable Membranes

In this paper we study the electrostatic interaction of a heterogeneously charged wall with a neutral semipermeable membrane. The wall consists of periodic stripes, where the charge density varies in one direction. The membrane is in a contact with a bulk reservoir of an electrolyte solution and separated from the wall by a thin film of salt-free liquid. One type of ions (small counterions) permeates into the gap and gives rise to a distance-dependent membrane potential, which translates into a repulsive electrostatic disjoining pressure due to an overlap of counterion clouds in the gap. To quantify it we use two complementary approaches. First, we propose a mean-field theory based on a linearized Poisson-Boltzmann equation and Fourier analysis. These calculations allow us to estimate the effect of a heterogeneous charge pattern at the wall on the induced heterogeneous membrane potential, and the value of the disjoining pressure as a function of the gap. Second, we perform Langevin dynamics simulations of the same system with explicit ions. The results of the two approaches are in good agreement with each other at low surface charge and small gap, but differ due to nonlinearity at the higher charge. These results demonstrate that a heterogeneity of the wall charge can lead to a huge reduction in the electrostatic repulsion, which could dramatically facilitate a self-assembly in complex synthetic and biological systems.

cond-mat.soft↗

arXiv2013

Effective hydrodynamic boundary conditions for microtextured surfaces

We report measurements of the hydrodynamic drag force acting on a smooth sphere falling down under gravity to a plane decorated with microscopic periodic grooves. Both surfaces are lyophilic, so that a liquid (silicone oil) invades the surface texture being in the Wenzel state. A significant decrease in the hydrodynamic resistance force as compared with that predicted for two smooth surfaces is observed. To quantify the effect of roughness we use the effective no-slip boundary condition, which is applied at the imaginary smooth homogeneous isotropic surface located at an intermediate position between top and bottom of grooves. Such an effective condition fully characterizes the force reduction measured with the real surface, and the location of this effective plane is related to geometric parameters of the texture by a simple analytical formula.

physics.flu-dyn↗

arXiv2013

Effective slip boundary conditions for arbitrary one-dimensional surfaces

In many applications it is advantageous to construct effective slip boundary conditions, which could fully characterize flow over patterned surfaces. Here we focus on laminar shear flows over smooth anisotropic surfaces with arbitrary scalar slip $b(y)$, varying in only one direction. We derive general expressions for eigenvalues of the effective slip-length tensor, and show that the transverse component is equal to a half of the longitudinal one with twice larger local slip, $2b(y)$. A remarkable corollary of this relation is that the flow along any direction of the 1D surface can be easily determined, once the longitudinal component of the effective slip tensor is found from the known spatially nonuniform scalar slip.

physics.flu-dyn↗

arXiv2012

Flow past superhydrophobic surfaces with cosine variation in local slip length

Anisotropic super-hydrophobic surfaces have the potential to greatly reduce drag and enhance mixing phenomena in microfluidic devices. Recent work has focused mostly on cases of super-hydrophobic stripes. Here, we analyze a relevant situation of cosine variation of the local slip length. We derive approximate formulae for maximal (longitudinal) and minimal (transverse) directional effective slip lengths that are in good agreement with the exact numerical solution and lattice-Bolzmann simulations for any surface slip fraction. The cosine texture can provide a very large effective (forward) slip, but it was found to be less efficient in generating a transverse flow as compared to super-hydrophobic stripes.

physics.flu-dyn↗

arXiv2012

Interactions of neutral semipermeable shells in asymmetric electrolyte solutions

We study the ionic equilibria and interactions of neutral semi-permeable spherical shells immersed in electrolyte solutions, including polyions. Although the shells are uncharged, only one type of ions of the electrolyte can permeate them, thus leading to a steric charge separation in the system. This gives rise to a charge accumulation inside the shell and a build up of concentration- dependent shell potential, which converts into a disjoining pressure between the neighboring shells. These are quantified by using the Poisson-Boltzmann and integral equations theory. In particular, we show that in case of low valency electrolytes, interactions between shells are repulsive and can be sufficiently strong to stabilize the shell dispersion. In contrast, the charge correlation effects in solutions of polyvalent ions result in attractions between the shells, with can lead to their aggregation.

cond-mat.soft↗

arXiv2012

Anisotropic flow in striped superhydrophobic channels

We report results of dissipative particle dynamics simulations and develop a semi-analytical theory of an anisotropic flow in a parallel-plate channel with two superhydrophobic striped walls. Our approach is valid for any local slip at the gas sectors and an arbitrary distance between the plates, ranging from a thick to a thin channel. It allows us to optimize area fractions, slip lengths, channel thickness and texture orientation to maximize a transverse flow. Our results may be useful for extracting effective slip tensors from global measurements, such as the permeability of a channel, in experiments or simulations, and may also find applications in passive microfluidic mixing.

physics.flu-dyn↗

arXiv2012

Electrostatic interaction of neutral semipermeable membranes

We consider an osmotic equilibrium between bulk solutions of polyelectrolyte bounded by semipermeable membranes and separated by a thin film of salt-free liquid. Although the membranes are neutral, the counter-ions of the polyelectrolyte molecules permeate into the gap and lead to a steric charge separation. This gives rise to a distance-dependent membrane potential, which translates into a repulsive electrostatic disjoining pressure. From the solution of the non-linear Poisson-Boltzmann equation we obtain the distribution of the potential and of ions. We then derive an explicit formula for the pressure exerted on the membranes and show that it deviates from the classical van't Hoff expression for the osmotic pressure. This difference is interpreted in terms of a repulsive electrostatic disjoining pressure originating from the overlap of counterion clouds inside the gap. We also develop a simplified theory based on a linearized Poisson-Boltzmann approach. A comparison with simulation of a primitive model for the electrolyte is provided and does confirm the validity of the theoretical predictions Beyond the fundamental result that the neutral surfaces can repel, this mechanism not only helps to control the adhesion and long-range interactions of living cells, bacteria, and vesicles, but also allows us to argue that electrostatic interactions should play enormous role in determining behavior and functions of systems bounded by semipermeable membranes.

cond-mat.soft↗

arXiv2012

Tensorial slip of super-hydrophobic channels

We describe a generalization of the tensorial slip boundary condition, originally justified for a thick (compared to texture period) channel, to any channel thickness. The eigenvalues of the effective slip length tensor, however, in general case become dependent on the gap and cannot be viewed as a local property of the surface, being a global characteristic of the channel. To illustrate the use of the tensor formalism we develop a semi-analytical theory of an effective slip in a parallel-plate channel with one super-hydrophobic striped and one hydrophilic surface. Our approach is valid for any local slip at the gas sectors and an arbitrary distance between the plates, ranging from a thick to a thin channel. We then present results of lattice Boltzmann simulations to validate the analysis. Our results may be useful for extracting effective slip tensors from global measurements, such as the permeability of a channel, in experiments or simulations.

physics.flu-dyn↗

arXiv2011

Electro-osmosis on anisotropic super-hydrophobic surfaces

We give a general theoretical description of electro-osmotic flow at striped super-hydrophobic surfaces in a thin double layer limit, and derive a relation between the electro-osmotic mobility and hydrodynamic slip-length tensors. Our analysis demonstrates that electro-osmotic flow shows a very rich behavior controlled by slip length and charge at the gas sectors. In case of uncharged liquid-gas interface, the flow is the same or inhibited relative to flow in homogeneous channel with zero interfacial slip. By contrast, it can be amplified by several orders of magnitude provided slip regions are uniformly charged. When gas and solid regions are oppositely charged, we predict a flow reversal, which suggests a possibility of huge electro-osmotic slip even for electro-neutral surfaces. On the basis of these observations we suggest strategies for practical microfluidic mixing devices. These results provide a framework for the rational design of super-hydrophobic surfaces.

cond-mat.soft↗

arXiv2011

Wetting, roughness and hydrodynamic slip

The hydrodynamic slippage at a solid-liquid interface is currently at the center of our understanding of fluid mechanics. For hundreds of years this science has relied upon no-slip boundary conditions at the solid-liquid interface that has been applied successfully to model many macroscopic experiments, and the state of this interface has played a minor role in determining the flow. However, the problem is not that simple and has been revisited recently. Due to the change in the properties of the interface, such as wettability and roughness, this classical boundary condition could be violated, leading to a hydrodynamic slip. In this chapter, we review recent advances in the understanding and expectations for the hydrodynamic boundary conditions in different situations, by focussing mostly on key papers from past decade. We highlight mostly the impact of hydrophobicity, roughness, and especially their combination on the flow properties. In particular, we show that hydrophobic slippage can be dramatically affected by the presence of roughness, by inducing novel hydrodynamic phenomena, such as giant interfacial slip, superfluidity, mixing, and low hydrodynamic drag. Promising directions for further research are also discussed.

cond-mat.soft↗

arXiv2011

Drag force on a sphere moving towards an anisotropic super-hydrophobic plane

We analyze theoretically a high-speed drainage of liquid films squeezed between a hydrophilic sphere and a textured super-hydrophobic plane, that contains trapped gas bubbles. A super-hydrophobic wall is characterized by parameters $L$ (texture characteristic length), $b_1$ and $b_2$ (local slip lengths at solid and gas areas), and $ϕ_1$ and $ϕ_2$ (fractions of solid and gas areas). Hydrodynamic properties of the plane are fully expressed in terms of the effective slip-length tensor with eigenvalues that depend on texture parameters and $H$ (local separation). The effect of effective slip is predicted to decrease the force as compared with expected for two hydrophilic surfaces and described by the Taylor equation. The presence of additional length scales, $L$, $b_1$ and $b_2$, implies that a film drainage can be much richer than in case of a sphere moving towards a hydrophilic plane. For a large (compared to $L$) gap the reduction of the force is small, and for all textures the force is similar to expected when a sphere is moving towards a smooth hydrophilic plane that is shifted down from the super-hydrophobic wall. The value of this shift is equal to the average of the eigenvalues of the slip-length tensor. By analyzing striped super-hydrophobic surfaces, we then compute the correction to the Taylor equation for an arbitrary gap. We show that at thinner gap the force reduction becomes more pronounced, and that it depends strongly on the fraction of the gas area and local slip lengths. For small separations we derive an exact equation, which relates a correction for effective slip to texture parameters. Our analysis provides a framework for interpreting recent force measurements in the presence of super-hydrophobic surface.

physics.flu-dyn↗

arXiv2011

Wetting, roughness and flow boundary conditions

We discuss how the wettability and roughness of a solid impacts its hydrodynamic properties. We see in particular that hydrophobic slippage can be dramatically affected by the presence of roughness. Owing to the development of refined methods for setting very well-controlled micro- or nanotextures on a solid, these effects are being exploited to induce novel hydrodynamic properties, such as giant interfacial slip, superfluidity, mixing, and low hydrodynamic drag, that could not be achieved without roughness.

cond-mat.soft↗