arXiv subjects

Oliver Jeong

Publications and source records attributed to Oliver Jeong.

At least 19 recordsLinked to original sources

arXiv2026

High efficiency superconducting filterbank with impedance-defined resolution for millimeter-wave spectroscopy

We present a high efficiency, moderate resolution on-chip superconducting filterbank spectrometer designed for line intensity mapping and broadband wave-like dark matter searches. Existing implementations used by the millimeter-wave community rely on resistive feedline termination for standing wave mitigation which caps the per-channel efficiency $η_\mathrm{ch}$ at 50\% and utilize microstrip resonators which highly couple the resolving power $\mathcal{R}=ν/δν$ and $η_\mathrm{ch}$ to thin-film dielectric loss. The architecture presented in this paper addresses these limitations by eliminating the termination resistor and employing niobium coplanar waveguide resonators patterned directly on single-crystal silicon, which fixes the resonator's internal quality factor by the silicon substrate property rather than by the loss tangent of a deposited film. The resolving power is set by the impedance ratio between the resonator and feedline. Electromagnetic and circuit simulations of a ten-channel filterbank near 90~GHz at unity oversampling show $\mathcal{R}=1170$ and $η_\mathrm{ch}> 78\%$, with no significant trend in efficiency across channels. A ten-channel prototype, designed for $\mathcal{R}=92\pm5$ and $η_\mathrm{ch}=(81\pm3)\%$ over 90--106~GHz with a 560~nm interlayer based on simulations, was fabricated and optically characterized, yielding $\mathcal{R}=208\pm74$ and $η_\mathrm{ch}=(77\pm6)\%$. Measured $η_\mathrm{ch}$ well above the 50\% termination limit, together with demonstrated impedance tuning of $\mathcal{R}$, validate the design principles of this filterbank spectrometer and establishes a route to high-efficiency, high-resolution on-chip spectrometer arrays.

astro-ph.IM↗

arXiv2026

Atmosphere mitigation in CMB observations using multi-frequency time-domain component separation

CMB observations from ground-based observatories are limited in sensitivity by the fluctuating emission from the Earth's atmosphere, mostly due to water vapor inhomogeneities. Even in atmospheric windows, this spurious signal remains the dominant source of contamination in the data. Traditional mitigation techniques include low-frequency filtering, or for polarization measurements specifically, pair-differencing or modulation with a rotating half-wave plate. The first method filters out a significant fraction of the target cosmological signal while the second leaves residuals due to imperfections, temperature to polarization leakage, or polarized atmospheric emission. In this work, we present a new data analysis framework, based on estimation of atmosphere emission templates using a multi-frequency focal plane. The core novelty of this setup is to have detectors dedicated to atmosphere monitoring, allowing the removal of atmospheric contamination with time-domain component separation techniques. We introduce a multipole-dependent atmospheric decontamination factor $A^\mathrm{atm}_\ell$ to quantify the relative reduction of the atmospheric contamination angular power spectrum achievable with this approach. Using this criterion, we demonstrate that our component separation pipeline can outperform a classical filter-bin map-making pipeline by a factor of 4000 for $30\le \ell \le 300$.

astro-ph.IM↗

arXiv2026

Joint Estimation of Properties of the Lunar Subsurface and Galactic Foregrounds with LuSEE-Night

The Lunar Surface Electromagnetics Experiment (LuSEE-Night) is a joint NASA-DOE-ESA low-frequency radio telescope that will reach the lunar far side in 2027. The unknown dielectric properties of the subsurface at the LuSEE-Night landing site impose the most significant limitation for precision instrument calibration, as reflections from the lunar subsurface can change the primary beam at the 10-20% level. Simulations of these effects have provided insight and concern, showing that the lunar subsurface modeled as a lossy dielectric can absorb a large amount of the power of the sky signal. While this absorption may not strongly impact the signal-to-noise ratio in a sky-noise-dominated regime, it could complicate the beam pattern and make the signal more difficult to model and interpret. We have simulated the far-field properties of the LuSEE-Night beam for varying dielectric profiles of the lunar subsurface. We find that varying the properties of the lunar subsurface has the most significant impact around the antenna resonance, impacting its amplitude, position and width. Conversely, changing the properties of the foreground impacts the data across the band. We use a Bayesian inference pipeline to jointly estimate parameters of a galactic foreground model and dielectric properties of the lunar subsurface around the LuSEE-Night landing site and find that parameters of both the galaxy and subsurface properties can be estimated jointly. While the modeling is somewhat idealized, we believe that the results are largely robust owing to the fact that spectral variations for plausible subsurface and galaxy models have very different spectral signatures.

astro-ph.IM↗

arXiv2026

Linear map-making with LuSEE-Night

LuSEE-Night is a pathfinder radio telescope on the lunar far side employing four 3-m monopole antennas arranged as two horizontal cross pseudo-dipoles on a rotational stage and sensitive to the radio sky in the 1-50 MHz frequency band. LuSEE-Night measures the corresponding 16 correlation products as a function of frequency. While each antenna combination measures radiation coming from a large area of the sky, their aggregate information as a function of phase in the lunar cycle and rotational stage position can be deconvolved into a low-resolution map of the sky. We study this deconvolution using linear map-making based on the Wiener filter algorithm. We illustrate how systematic effects can be effectively marginalised over as contributions to the noise covariance and demonstrate this technique on beam knowledge uncertainty and gain fluctuations. With reasonable assumptions about instrument performance, we show that LuSEE-Night should be able to map the sub-50 MHz sky at a ~5-degree resolution.

astro-ph.IM↗

arXiv2025

Fast far-sidelobe modeling for centimeter to sub-millimeter astrophysical observations

Next-generation centimeter to sub-millimeter telescopes require exquisite control over instrumental far-sidelobe response to accurately measure faint signals like the Cosmic Microwave Background B modes. Because existing electromagnetic modeling methods are computationally expensive, we developed a novel, diffraction-based beam modeling method for rapid and low-cost calculations. We applied this methodology to model the BICEP3 far-sidelobes and found good qualitative agreement with in situ beam measurements. Using this validated simulated beam, we calculated the sidelobe temperature pickup for a specific observation scenario: scanning near the slopes of Cerro Toco in the Atacama Desert. This rapid, predictive framework is most valuable as a tool for optimizing instrument baffling and identifying efficient scan strategies during the conceptual design phase.

astro-ph.IM↗

arXiv2025

Constraints on the polarization angle oscillations of the Crab Nebula with the Simons Array and its applications to the search for axion-like particles

We present a search for polarization oscillation of the Crab Nebula, also known as Tau A, at millimeter wavelengths using observations with the Simons Array, the successor experiment to POLARBEAR. We follow up on previous work by POLARBEAR using 90 GHz band data of the 2023 observing season of the Simons Array to evaluate the variability of Tau A's polarization angle. Tau A is widely used as a polarization angle calibration source in millimeter-wave astronomy, and thus it is necessary to validate the stability. Additionally, an interesting application of the time-resolved polarimetry of Tau A is to search for axion-like particles (ALPs). We do not detect a global signal across the frequencies considered in this analysis and place a median 95% upper bound of polarization oscillation amplitude $A<0.12^{\circ}$ over oscillation frequencies from 3.39 year$^{-1}$ to 1.50 day$^{-1}$. This constrains the ALP-photon coupling at a median 95% upper bound of $g_{aγγ}< 3.84\times 10^{-12}\times\left(m_a/10^{-21}\,\mathrm{eV}\right)$ in the mass range from $4.4\times10^{-22}$ to $7.2\times10^{-20}$ eV, assuming the ALP constitutes all of dark matter, its field is a stochastic Gaussian field, and it is the sole source of Tau A's polarization angle oscillation. Additionally, we do not detect signal at the frequencies where 2.5$σ$ hints were previously reported by POLARBEAR, but we do not exclude these signals at the 95% confidence level.

astro-ph.CO↗

arXiv2025

A novel double-rim forebaffle design for centimeter to sub-millimeter astrophysical observations

Stray radiation of various origin is a major source of degradation of centimeter to sub-millimeter astronomical observations. This is particularly problematic for the detection of signals such as faint cosmic microwave background polarization B modes, or for mapping large-scale extragalactic or Galactic diffuse emission. In this paper, we propose a double-rim forebaffle design to reduce the impact of such stray radiation contamination. Using qualitative arguments and numerical simulations, we show that such a design has the potential to substantially improve the quality of future observations.

astro-ph.IM↗

arXiv2025

A measurement of atmospheric circular polarization with POLARBEAR

At millimeter wavelengths, the atmospheric emission is circularly polarized owing to the Zeeman splitting of molecular oxygen by the Earth's magnetic field. We report a measurement of the signal in the 150 GHz band using 3 years of observational data with the \textsc{Polarbear} project. Non-idealities of a continuously rotating half-wave plate (HWP) partially convert circularly polarized light to linearly polarized light. While \textsc{Polarbear} detectors are sensitive to linear polarization, this effect makes them sensitive to circular polarization. Although this was not the intended use, we utilized this conversion to measure circular polarization. We reconstruct the azimuthal gradient of the circular polarization signal and measure its dependency from the scanning direction and the detector bandpass. We compare the signal with a simulation based on atmospheric emission theory, the detector bandpass, and the HWP leakage spectrum model. We find the ratio of the observed azimuthal slope to the simulated slope is $0.92 \pm 0.01\rm{(stat)} \pm 0.07\rm{(sys)}$. This ratio corresponds to a brightness temperature of $3.8\,\mathrm{m K}$ at the effective band center of $121.8\,\mathrm{GHz}$ and bandwidth of $3.5\,\mathrm{GHz}$ estimated from representative detector bandpass and the spectrum of Zeeman emission. This result validates our understanding of the instrument and reinforces the feasibility of measuring the circular polarization using the imperfection of continuously rotating HWP. Continuously rotating HWP is popular in ongoing and future cosmic microwave background experiments to modulate the polarized signal. This work shows a method for signal extraction and leakage subtraction that can help measuring circular polarization in such experiments.

astro-ph.IM↗

arXiv2024

Exploration of the polarization angle variability of the Crab Nebula with POLARBEAR and its application to the search for axion-like particles

The Crab Nebula, also known as Tau A, is a polarized astronomical source at millimeter wavelengths. It has been used as a stable light source for polarization angle calibration in millimeter-wave astronomy. However, it is known that its intensity and polarization vary as a function of time at a variety of wavelengths. Thus, it is of interest to verify the stability of the millimeter-wave polarization. If detected, polarization variability may be used to better understand the dynamics of Tau~A, and for understanding the validity of Tau~A as a calibrator. One intriguing application of such observation is to use it for the search of axion-like particles (ALPs). Ultralight ALPs couple to photons through a Chern-Simons term, and induce a temporal oscillation in the polarization angle of linearly polarized sources. After assessing a number of systematic errors and testing for internal consistency, we evaluate the variability of the polarization angle of the Crab Nebula using 2015 and 2016 observations with the 150 GHz POLARBEAR instrument. We place a median 95% upper bound of polarization oscillation amplitude $A < 0.065^\circ$ over the oscillation frequencies from $0.75~\mathrm{year}^{-1}$ to $0.66~\mathrm{hour}^{-1}$. Assuming that no sources other than ALP are causing Tau A's polarization angle variation, that the ALP constitutes all the dark matter, and that the ALP field is a stochastic Gaussian field, this bound translates into a median 95% upper bound of ALP-photon coupling $g_{aγγ} < 2.16\times10^{-12}\,\mathrm{GeV}^{-1}\times(m_a/10^{-21} \mathrm{eV})$ in the mass range from $9.9\times10^{-23} \mathrm{eV}$ to $7.7\times10^{-19} \mathrm{eV}$. This demonstrates that this type of analysis using bright polarized sources is as competitive as those using the polarization of cosmic microwave background in constraining ALPs.

astro-ph.CO↗

arXiv2023

Broadband plasma spray anti-reflection coating technology for millimeter-wave astrophysics

We present a broadband plasma spray anti-reflection (AR) coating technology for millimeter-wave astrophysics experiments with large-format, cryogenic optics. By plasma spraying alumina- and silica-based powders, we have produced coatings of tunable index of refraction and thickness, low loss, and coefficient of thermal expansion matched to alumina substrates. We demonstrate two-layer AR coatings on alumina with reflection below 5% over 82% and 69% fractional bandwidths for 90/150 and 220/280 GHz passband designs, respectively, and band-averaged absorption loss reduced to ~1% at 100 K for both AR coatings. We describe the design, tolerance, fabrication process, and optical measurements of these AR coatings.

astro-ph.IM↗

arXiv2020

Measurement of the Cosmic Microwave Background Polarization Lensing Power Spectrum from Two Years of POLARBEAR Data

We present a measurement of the gravitational lensing deflection power spectrum reconstructed with two seasons cosmic microwave background polarization data from the POLARBEAR experiment. Observations were taken at 150 GHz from 2012 to 2014 which survey three patches of sky totaling 30 square degrees. We test the consistency of the lensing spectrum with a Cold Dark Matter (CDM) cosmology and reject the no-lensing hypothesis at a confidence of 10.9 sigma including statistical and systematic uncertainties. We observe a value of A_L = 1.33 +/- 0.32 (statistical) +/- 0.02 (systematic) +/- 0.07 (foreground) using all polarization lensing estimators, which corresponds to a 24% accurate measurement of the lensing amplitude. Compared to the analysis of the first year data, we have improved the breadth of both the suite of null tests and the error terms included in the estimation of systematic contamination.

astro-ph.CO↗

arXiv2019

Evidence for the Cross-correlation between Cosmic Microwave Background Polarization Lensing from POLARBEAR and Cosmic Shear from Subaru Hyper Suprime-Cam

We present the first measurement of cross-correlation between the lensing potential, reconstructed from cosmic microwave background (CMB) {\it polarization} data, and the cosmic shear field from galaxy shapes. This measurement is made using data from the POLARBEAR CMB experiment and the Subaru Hyper Suprime-Cam (HSC) survey. By analyzing an 11~deg$^2$ overlapping region, we reject the null hypothesis at 3.5$σ$\ and constrain the amplitude of the {\bf cross-spectrum} to $\widehat{A}_{\rm lens}=1.70\pm 0.48$, where $\widehat{A}_{\rm lens}$ is the amplitude normalized with respect to the Planck~2018{} prediction, based on the flat $Λ$ cold dark matter cosmology. The first measurement of this {\bf cross-spectrum} without relying on CMB temperature measurements is possible due to the deep POLARBEAR map with a noise level of ${\sim}$6\,$μ$K-arcmin, as well as the deep HSC data with a high galaxy number density of $n_g=23\,{\rm arcmin^{-2}}$. We present a detailed study of the systematics budget to show that residual systematics in our results are negligibly small, which demonstrates the future potential of this cross-correlation technique.

astro-ph.CO↗

arXiv2018

The Simons Observatory: Instrument Overview

The Simons Observatory (SO) will make precise temperature and polarization measurements of the cosmic microwave background (CMB) using a set of telescopes which will cover angular scales between 1 arcminute and tens of degrees, contain over 60,000 detectors, and observe at frequencies between 27 and 270 GHz. SO will consist of a 6 m aperture telescope coupled to over 30,000 transition-edge sensor bolometers along with three 42 cm aperture refractive telescopes, coupled to an additional 30,000+ detectors, all of which will be located in the Atacama Desert at an altitude of 5190 m. The powerful combination of large and small apertures in a CMB observatory will allow us to sample a wide range of angular scales over a common survey area. SO will measure fundamental cosmological parameters of our universe, constrain primordial fluctuations, find high redshift clusters via the Sunyaev-Zel`dovich effect, constrain properties of neutrinos, and trace the density and velocity of the matter in the universe over cosmic time. The complex set of technical and science requirements for this experiment has led to innovative instrumentation solutions which we will discuss. The large aperture telescope will couple to a cryogenic receiver that is 2.4 m in diameter and nearly 3 m long, creating a number of technical challenges. Concurrently, we are designing the array of cryogenic receivers housing the 42 cm aperture telescopes. We will discuss the sensor technology SO will use and we will give an overview of the drivers for and designs of the SO telescopes and receivers, with their cold optical components and detector arrays.

astro-ph.IM↗

arXiv2018

A large-diameter cryogenic rotation stage for half-wave plate polarization modulation on the POLARBEAR-2 experiment

We describe the design of a cryogenic rotation stage (CRS) for use with the cryogenic half-wave plate (CHWP) polarization modulator on the POLARBEAR-2b and POLARBEAR-2c (PB2b/c) cosmic microwave background (CMB) experiments, the second and third installments of the Simons Array. Rapid modulation of the CMB polarization signal using a CHWP suppresses 1/f contamination due to atmospheric turbulence and allows a single polarimeter to measure both polarization states, mitigating systematic effects that arise when differencing orthogonal detectors. To modulate the full detector array while avoiding excess photon loading due to thermal emission, the CHWP must have a clear-aperture diameter of > 450 mm and be cooled to < 100 K. We have designed a 454-mm-clear-aperture, < 65 K CRS using a superconducting magnetic bearing driven by a synchronous magnetic motor. We present the specifications for the CRS, its interfacing to the PB2b/c receiver cryostat, its performance in a stand-alone test, and plans for future work.

astro-ph.IM↗

arXiv2018

Optical Characterization of the SPT-3G Focal Plane

The third-generation South Pole Telescope camera is designed to measure the cosmic microwave background across three frequency bands (95, 150 and 220 GHz) with ~16,000 transition-edge sensor (TES) bolometers. Each multichroic pixel on a detector wafer has a broadband sinuous antenna that couples power to six TESs, one for each of the three observing bands and both polarization directions, via lumped element filters. Ten detector wafers populate the focal plane, which is coupled to the sky via a large-aperture optical system. Here we present the frequency band characterization with Fourier transform spectroscopy, measurements of optical time constants, beam properties, and optical and polarization efficiencies of the focal plane. The detectors have frequency bands consistent with our simulations, and have high average optical efficiency which is 86%, 77% and 66% for the 95, 150 and 220 GHz detectors. The time constants of the detectors are mostly between 0.5 ms and 5 ms. The beam is round with the correct size, and the polarization efficiency is more than 90% for most of the bolometers

astro-ph.IM↗

arXiv2017

CMB-S4 Technology Book, First Edition

CMB-S4 is a proposed experiment to map the polarization of the Cosmic Microwave Background (CMB) to nearly the cosmic variance limit for angular scales that are accessible from the ground. The science goals and capabilities of CMB-S4 in illuminating cosmic inflation, measuring the sum of neutrino masses, searching for relativistic relics in the early universe, characterizing dark energy and dark matter, and mapping the matter distribution in the universe have been described in the CMB-S4 Science Book. This Technology Book is a companion volume to the Science Book. The ambitious science goals of CMB-S4, a "Stage-4" experiment, require a step forward in experimental capability from the current Stage=II experiments. To guide this process, we summarize the current state of CMB instrumentation technology, and identify R&D efforts necessary to advance it for use in CMB-S4. The book focuses on technical challenges in four broad areas: Telescope Design; Receiver Optics; Focal-Plane Optical Coupling; and Focal-Plane Sensor and Readout.

astro-ph.IM↗

arXiv2017

Performance of a continuously rotating half-wave plate on the POLARBEAR telescope

A continuously rotating half-wave plate (CRHWP) is a promising tool to improve the sensitivity to large angular scales in cosmic microwave background (CMB) polarization measurements. With a CRHWP, single detectors can measure three of the Stokes parameters, $I$, $Q$ and $U$, thereby avoiding the set of systematic errors that can be introduced by mismatches in the properties of orthogonal detector pairs. We focus on the implementation of CRHWPs in large aperture telescopes (i.e. the primary mirror is larger than the current maximum half-wave plate diameter of $\sim$0.5 m), where the CRHWP can be placed between the primary mirror and focal plane. In this configuration, one needs to address the intensity to polarization ($I{\rightarrow}P$) leakage of the optics, which becomes a source of 1/f noise and also causes differential gain systematics that arise from CMB temperature fluctuations. In this paper, we present the performance of a CRHWP installed in the POLARBEAR experiment, which employs a Gregorian telescope with a 2.5 m primary illumination pattern. The CRHWP is placed near the prime focus between the primary and secondary mirrors. We find that the $I{\rightarrow}P$ leakage is larger than the expectation from the physical properties of our primary mirror, resulting in a 1/f knee of 100 mHz. The excess leakage could be due to imperfections in the detector system, i.e. detector non-linearity in the responsivity and time-constant. We demonstrate, however, that by subtracting the leakage correlated with the intensity signal, the 1/f noise knee frequency is reduced to 32 mHz ($\ell \sim$39 for our scan strategy), which is very promising to probe the primordial B-mode signal. We also discuss methods for further noise subtraction in future projects where the precise temperature control of instrumental components and the leakage reduction will play a key role.

astro-ph.IM↗

arXiv2016

Making maps of Cosmic Microwave Background polarization for B-mode studies: the POLARBEAR example

Analysis of cosmic microwave background (CMB) datasets typically requires some filtering of the raw time-ordered data. Filtering is frequently used to minimize the impact of low frequency noise, atmospheric contributions and/or scan synchronous signals on the resulting maps. In this work we explicitly construct a general filtering operator, which can unambiguously remove any set of unwanted modes in the data, and then amend the map-making procedure in order to incorporate and correct for it. We show that such an approach is mathematically equivalent to the solution of a problem in which the sky signal and unwanted modes are estimated simultaneously and the latter are marginalized over. We investigate the conditions under which this amended map-making procedure can render an unbiased estimate of the sky signal in realistic circumstances. We then study the effects of time-domain filtering on the noise correlation structure in the map domain, as well as impact it may have on the performance of the popular pseudo-spectrum estimators. We conclude that although maps produced by the proposed estimators arguably provide the most faithful representation of the sky possible given the data, they may not straightforwardly lead to the best constraints on the power spectra of the underlying sky signal and special care may need to be taken to ensure this is the case. By contrast, simplified map-makers which do not explicitly correct for time-domain filtering, but leave it to subsequent steps in the data analysis, may perform equally well and be easier and faster to implement. We focus on polarization-sensitive measurements targeting the B-mode component of the CMB signal and apply the proposed methods to realistic simulations based on characteristics of an actual CMB polarization experiment, POLARBEAR.

astro-ph.IM↗