arXiv subjects

Pablo Marin-Palomo

Publications and source records attributed to Pablo Marin-Palomo.

16 recordsLinked to original sources

arXiv2026

Nanosecond-scale discrete wavelength switching in feedback-controlled single-gain-section multi-wavelength lasers

We investigate discrete wavelength switching in single-gain-section multi-wavelength lasers monolithically integrated on InP with phase-controlled optical-feedback. By modulating the feedback phase, nanosecond-scale wavelength switching is experimentally demonstrated with transition times below 2.5 ns. Measurements consistently show that the switching time decreases with stronger optical feedback and larger phase-modulation amplitudes. Transitions from lower to higher modal gain are faster. We support the experimental observations with a multi-mode extension of the Lang-Kobayashi rate-equation model. We analyze the influence of laser, feedback-cavity, and modulation parameters on the switching dynamics, and highlight the role of mode coupling. These results highlight the potential of integrated multi-wavelength lasers for compact and high-speed all-optical networking systems.

physics.optics↗

arXiv2025

Theoretical analysis of optical feedback-controlled emission of dual-wavelength lasers

Dual and multi-wavelength lasers, i.e., lasers with the ability to emit at two or more wavelengths in a controlled fashion, represent an exciting new twist in laser physics. Harnessing the mode competition to control them better remains, however, a challenge. In this work, we numerically explore the effect of optical feedback on the emission properties of a dual-wavelength laser using a rate equation model. We focus on switching capability and investigate the impact of key laser and feedback parameters. We connect the emergence of simultaneous emission to a lower cross-saturation between modes, and demonstrate that robust switching can be achieved using a short feedback cavity and a sufficiently strong feedback. In particular and in contrast to previous publications, we highlight that the feedback phase difference between the two modes is not a critical parameter. Our results are consistent with recent experimental observations, supporting the relevance of feedback-based control techniques for multi-wavelength lasers.

physics.optics↗

arXiv2025

Agile and Broadband All-Optical Wavelength Conversion with Multi-Wavelength Lasers

We demonstrate a novel approach to all-optical wavelength conversion (AOWC) using a monolithically integrated InP multi-wavelength laser (MWL). By exploiting carrier-induced gain modulation and intermodal coupling within the common gain section, we achieve data wavelength conversion over a 1.3 THz range for signals up to 10 GBd, without the need for an external probe laser. The scheme relies on optical injection of the data signal into the MWL, where strong mode coupling enables transfer of the modulation to other longitudinal modes. A monolithically integrated feedback cavity provides agile switching between three longitudinal modes or even broadcasting across the three channels by adjusting the feedback phase. We evaluate the signal quality of the converted data through BER measurements for various symbol rates, showing both transparent conversion and, at low injection powers, even net signal gain. Complementary numerical simulations, based on a multimode extension of the Lang-Kobayashi rate equations, reveal the role of modal gain imbalance and cross-saturation in shaping the conversion efficiency. These results establish a scalable, compact, and energy-efficient route toward agile AOWC devices.

physics.optics↗

arXiv2025

Photonic Filter for THz via optical injection into a feedback-controlled on-chip multi-wavelength laser

The growing demand for ultra-fast wireless data transmission is accelerating the exploration of THz frequencies for next-generation wireless communication systems. THz photonics provides a platform for generating, processing, and detecting THz signals by upconversion to the optical domain and leveraging the large available bandwidth of photonic devices at optical frequencies. However, efficient, tunable, and agile photonic filters remain a significant technical challenge. Here, we present a monolithically-integrated, feedback-controlled multiwavelength laser (MWL) enabling photonic filtering through regenerative amplification induced by optical signal injection. The feedback cavity enables agile control of the filter response by tuning the feedback phase. We experimentally demonstrate selective filtering of an upconverted THz signal comprising two channels separated by 34 GHz and offset by 1.3 THz from the carrier. Using a broadband signal, our photonic filter achieves up to 20dB suppression ratio, 3-dB bandwidths as narrow as 160 MHz, and optical gain of up to 15 dB for lowpower optical signals commonly obtained after THz-to-optical conversion, making it highly attractive for THz communication links.

physics.optics↗

arXiv2024

Response of a multi-wavelength laser to single-sideband optical injection

Single-mode semiconductor lasers subject to optical injection have been shown to trigger a wide range of dynamical behavior from injection locking to chaos. Multi-wavelength lasers add even more degrees of freedom and complexity to the dynamical repertoire potentially unlocking new functionalities for applications ranging from THz generation and processing to all-optical memories. In particular, leveraging the inherent mode coupling in multi-wavelength lasers, spectral multiplication over a THz range of an injected optical signal has been shown. While most of the research on optical injection has been focused on single-mode semiconductor lasers, the dynamical behavior of multi-wavelength lasers, particularly when subjected to injection of amplitude-modulated signals remains vastly unexplored. In this work, we numerically and experimentally investigate the response of an on-chip dual-wavelength laser subject to the optical injection of a single-sideband signal around one of the modes of the laser. Our findings show an asymmetric power evolution of the sidebands appearing around both the injected and un-injected modes with respect to the modulation frequency. The power and bandwidth of the sideband signals strongly depend on the resonance frequency produced by the interference between the cavity mode and the injection, which can be tailored by twerking the strength and the detuning of the injection. The outcomes of our numerical investigations, based on rate equations, align closely with the experimental results highlighting the influence of key injection and laser parameters.

physics.optics↗

arXiv2023

Slice-Less Optical Arbitrary Waveform Measurement (OAWM) in a Bandwidth of More than 600 GHz Using Soliton Microcombs

We propose and demonstrate a novel scheme for optical arbitrary waveform measurement (OAWM) that exploits chip-scale Kerr soliton combs as highly scalable multiwavelength local oscillators (LO) for ultra-broadband full-field waveform acquisition. In contrast to earlier concepts, our approach does not require any optical slicing filters and thus lends itself to efficient implementation on state-of-the-art high-index-contrast integration platforms such as silicon photonics. The scheme allows to measure truly arbitrary waveforms with high accuracy, based on a dedicated system model which is calibrated by means of a femtosecond laser with known pulse shape. We demonstrated the viability of the approach in a proof-of-concept experiment by capturing an optical waveform that contains multiple 16 QAM and 64 QAM wavelength-division multiplexed (WDM) data signals with symbol rates of up to 80 GBd, reaching overall line rates of up to 1.92 Tbit/s within an optical acquisition bandwidth of 610 GHz. To the best of our knowledge, this is the highest bandwidth that has so far been demonstrated in an OAWM experiment.

physics.optics↗

arXiv2022

Performance and control strategy of an integrated tunable laser with a single intra-cavity AMZI filter

Asymmetric Mach-Zehnder interferometers (AMZIs) can, in principle, enable continuous wavelength tuning of a laser when used as an intra-cavity filter. Their simplicity and good compatibility with generic foundry platforms are major advantages. However, the difficulty to develop a well-defined and robust control strategy is an important drawback which restricts the use-cases of these tunable lasers. Here, we make an in-depth investigation of the tunability properties of a laser including a single-stage AMZI in its cavity. We find that due to imperfections of Electro-Optic Phase Modulators (EOPMs), the dependence of the phase variation with the applied voltage is not linear. Because integrated EOPMs cannot be individually calibrated, these nonlinearities prevent a precise and independent tuning of the phase and amplitude of the AMZI transfer function, and thus continuous tuning cannot be reliably achieved. To overcome this issue, we propose a refined control strategy which allows for semi-continuous tuning. With this approach, we demonstrate a piece-wise continuous tuning of the emission wavelength by taking advantage of the coupling between amplitude and phase in the AMZI response. With our refined control strategy, we achieve tuning of the emission wavelength over the full free spectral range (FSR) of the AMZI.

physics.optics↗

arXiv2022

Mode-coupling effects in an optically-injected dual-wavelength laser

Lasers designed to emit at multiple and controllable modes, or multi-wavelength lasers, have the potential to become key building blocks for future microwave photonic technologies. While many interesting schemes relying on optical injection have been proposed, the nonlinear mode coupling between different modes of a multi-wavelength laser and their dynamical behavior under optical injection remains vastly unexplored. Here, we experimentally and numerically study the effect of optical injection around the suppressed mode of a dual12 wavelength laser and the resulting interactions with the dominant mode. We highlight a wavelength shift of the dominant mode triggered by injection locking of the suppressed mode and report a strong impact of the mode suppression ratio on the locking range. Finally, we show numerically that the cross-coupling parameter between the two modes might have a key role in this effect.

physics.optics↗

arXiv2021

Ultra-broadband polarization beam splitter and rotator based on 3D-printed waveguides

Multi-photon lithography has emerged as a powerful tool for photonic integration, allowing to complement planar photonic circuits by 3D-printed freeform structures such as waveguides or micro-optical elements. These structures can be fabricated with high precision on the facets of optical devices and lend themselves to highly efficient package-level chip-chip-connections in photonic assemblies. However, plain light transport and efficient coupling is far from exploiting the full geometrical design freedom that is offered by 3D laser lithography. Here, we extend the functionality of 3D-printed optical structures to manipulation of optical polarization states. We demonstrate compact ultra-broadband polarization beam splitters (PBS) that can be combined with polarization rotators (PR) and mode-field adapters into a monolithic 3D-printed structure, fabricated directly on the facets of optical devices. In a proof-of-concept experiment, we demonstrate measured polarization extinction ratios beyond 11 dB over a bandwidth of 350 nm at near-infrared (NIR) telecommunication wavelengths around 1550 nm. We demonstrate the viability of the device by receiving a 640 Gbit/s dual-polarization data signal using 16-state quadrature amplitude modulation (16QAM), without any measurable optical-signal-to-noise-ratio (OSNR) penalty compared to a commercial PBS.

physics.optics↗

arXiv2020

Mode-locked laser timing jitter limitation in optically enabled, spectrally sliced ADCs

Novel analog-to-digital converter (ADC) architectures are motivated by the demand for rising sampling rates and effective number of bits (ENOB). The main limitation on ENOB in purely electrical ADCs lies in the relatively high jitter of oscillators, in the order of a few tens of fs for state-of-the-art components. When compared to the extremely low jitter obtained with best-in-class Ti:sapphire mode-locked lasers (MLL), in the attosecond range, it is apparent that a mixed electrical-optical architecture could significantly improve the converters' ENOB. We model and analyze the ENOB limitations arising from optical sources in optically enabled, spectrally sliced ADCs, after discussing the system architecture and implementation details. The phase noise of the optical carrier, serving for electro-optic signal transduction, is shown not to propagate to the reconstructed digitized signal and therefore not to represent a fundamental limit. The optical phase noise of the MLL used to generate reference tones for individual slices also does not fundamentally impact the converted signal, so long as it remains correlated among all the comb lines. On the other hand, the timing jitter of the MLL, as also reflected in its RF linewidth, is fundamentally limiting the ADC performance, since it is directly mapped as jitter to the converted signal. The hybrid nature of a photonically enabled, spectrally sliced ADC implies the utilization of a number of reduced bandwidth electrical ADCs to convert parallel slices, resulting in the propagation of jitter from the electrical oscillator supplying their clock. Due to the reduced sampling rate of the electrical ADCs, as compared to the overall system, the overall noise performance of the presented architecture is substantially improved with respect to a fully electrical ADC.

eess.SP↗

arXiv2019

Coherent WDM transmission using quantum-dash mode-locked laser diodes as multi-wavelength source and local oscillator

Quantum-dash (QD) mode-locked laser diodes (MLLD) lend themselves as chip-scale frequency comb generators for highly scalable wavelength-division multiplexing (WDM) links in future data-center, campus-area, or metropolitan networks. Driven by a simple DC current, the devices generate flat broadband frequency combs, containing tens of equidistant optical tones with line spacings of tens of GHz. Here we show that QD-MLLDs can not only be used as multi-wavelength light sources at a WDM transmitter, but also as multi-wavelength local oscillators (LO) for parallel coherent reception. In our experiments, we demonstrate transmission of an aggregate data rate of 4.1 Tbit/s (23x45 GBd PDM-QPSK) over 75 km standard single-mode fiber (SSMF). To the best of our knowledge, this represents the first demonstration of a coherent WDM link that relies on QD-MLLD both at the transmitter and the receiver.

physics.app-ph↗

arXiv2019

OSNR limitations of chip-based optical frequency comb sources for WDM coherent communications

Optical frequency combs have the potential to become key building blocks of optical communication subsystems. The strictly equidistant, narrow-band spectral lines of a frequency comb can serve both as carriers for massively parallel data transmission and as local oscillator for coherent reception. Recent experiments have demonstrated the viability of various chip-based comb generator concepts for communication applications, offering transmission capacities of tens of Tbit/s. Here, we investigate the influence of the comb line power and of the carrier-to-noise power ratio on the performance of a frequency comb in a WDM system. We distinguish two regimes of operation depending on whether the comb source or the transmission link limits the performance of the system, i.e., defines the link reach, restricts the choice of modulation format and sets the maximum symbol rate. Finally, we investigate the achievable OSNR and channel capacity when using the tones of a soliton Kerr frequency comb as multi-wavelength carriers for WDM systems.

eess.SP↗

arXiv2019

Comb-based WDM transmission at 10 Tbit/s using a DC-driven quantum-dash mode-locked laser diode

Chip-scale frequency comb generators have the potential to become key building blocks of compact wavelength-division multiplexing (WDM) transceivers in future metropolitan or campus-area networks. Among the various comb generator concepts, quantum-dash (QD) mode-locked laser diodes (MLLD) stand out as a particularly promising option, combining small footprint with simple operation by a DC current and offering flat broadband comb spectra. However, the data transmission performance achieved with QD-MLLD was so far limited by strong phase noise of the individual comb tones, restricting experiments to rather simple modulation formats such as quadrature phase shift keying (QPSK) or requiring hard-ware-based compensation schemes. Here we demonstrate that these limitations can be over-come by digital symbol-wise phase tracking algorithms, avoiding any hardware-based phase-noise compensation. We demonstrate 16QAM dual-polarization WDM transmission on 38 channels at an aggregate net data rate of 10.68 Tbit/s over 75 km of standard single-mode fiber. To the best of our knowledge, this corresponds to the highest data rate achieved through a DC-driven chip-scale comb generator without any hardware-based phase-noise reduction schemes.

eess.SP↗

arXiv2018

Hybrid integration of silicon photonics circuits and InP lasers by photonic wire bonding

Efficient coupling of III-V light sources to silicon photonic circuits is one of the key challenges of integrated optics. Important requirements are low coupling losses, as well as small footprint and high yield of the overall assembly, along with the ability to use automated processes for large-scale production. In this paper, we demonstrate that photonic wire bonding addresses these challenges by exploiting direct-write two-photon lithography for in-situ fabrication of three-dimensional freeform waveguides between optical chips. In a series proof-of-concept experiments, we connect InP-based horizontal-cavity surface emitting lasers (HCSEL) to passive silicon photonic circuits with insertion losses down to 0.4 dB. To the best of our knowledge, this is the most efficient interface between an InP light source and a silicon photonic chip that has so far been demonstrated. Our experiments represent a key step in advancing photonic wire bonding to a universal integration platform for hybrid photonic multi-chip assemblies that combine known-good dies of different materials to high-performance hybrid multi-chip modules.

physics.app-ph↗

arXiv2017

Ultrafast optical ranging using microresonator soliton frequency combs

Light detection and ranging (LIDAR) is critical to many fields in science and industry. Over the last decade, optical frequency combs were shown to offer unique advantages in optical ranging, in particular when it comes to fast distance acquisition with high accuracy. However, current comb-based concepts are not suited for emerging high-volume applications such as drone navigation or autonomous driving. These applications critically rely on LIDAR systems that are not only accurate and fast, but also compact, robust, and amenable to cost-efficient mass-production. Here we show that integrated dissipative Kerr-soliton (DKS) comb sources provide a route to chip-scale LIDAR systems that combine sub-wavelength accuracy and unprecedented acquisition speed with the opportunity to exploit advanced photonic integration concepts for wafer-scale mass production. In our experiments, we use a pair of free-running DKS combs, each providing more than 100 carriers for massively parallel synthetic-wavelength interferometry. We demonstrate dual-comb distance measurements with record-low Allan deviations down to 12 nm at averaging times of 14 $μ$s as well as ultrafast ranging at unprecedented measurement rates of up to 100 MHz. We prove the viability of our technique by sampling the naturally scattering surface of air-gun projectiles flying at 150 m/s (Mach 0.47). Combining integrated dual-comb LIDAR engines with chip-scale nanophotonic phased arrays, the approach could allow widespread use of compact ultrafast ranging systems in emerging mass applications.

physics.optics↗

arXiv2017

Microresonator solitons for massively parallel coherent optical communications

Optical solitons are waveforms that preserve their shape while propagating, relying on a balance of dispersion and nonlinearity. Soliton-based data transmission schemes were investigated in the 1980s, promising to overcome the limitations imposed by dispersion of optical fibers. These approaches, however, were eventually abandoned in favor of wavelength-division multiplexing (WDM) schemes that are easier to implement and offer improved scalability to higher data rates. Here, we show that solitons may experience a comeback in optical communications, this time not as a competitor, but as a key element of massively parallel WDM. Instead of encoding data on the soliton itself, we exploit continuously circulating dissipative Kerr solitons (DKS) in a microresonator. DKS are generated in an integrated silicon nitride microresonator by four-photon interactions mediated by Kerr nonlinearity, leading to low-noise, spectrally smooth and broadband optical frequency combs. In our experiments, we use two interleaved soliton Kerr combs to transmit a data stream of more than 50Tbit/s on a total of 179 individual optical carriers that span the entire telecommunication C and L bands. Equally important, we demonstrate coherent detection of a WDM data stream by using a pair of microresonator Kerr soliton combs - one as a multi-wavelength light source at the transmitter, and another one as a corresponding local oscillator (LO) at the receiver. This approach exploits the scalability advantages of microresonator soliton comb sources for massively parallel optical communications both at the transmitter and receiver side. Taken together, the results prove the significant potential of these sources to replace arrays of continuous-wave lasers in high-speed communications.

nlin.PS↗