SearcharxivSearch

arXiv subjects

Paolo Ruggi

Publications and source records attributed to Paolo Ruggi.

11 recordsLinked to original sources

Mechanical Long Baseline Differential Gradiometers as Low Frequency Gravitational Wave Detectors

We present a new differential mechanical gradiometer for the detection of low-frequency Gravitational Waves. The frequency range is 0.05 to 1 Hz, a frequency gap not covered either by future space-based detectors such as LISA or by ground-based observatories such as Einstein Telescope or Cosmic Explorer. The proposed detection principle is similar to antennas based on torsion pendulums but solves the problem of physical confinement of these antennas by operating vertically and by having a counterweight at one end of each bar and a mass suspended from a long wire at the other. With this configuration, we enlarge the gravitational force acting on the system \textit{without} changing the moment of inertia of the system, so that we move from a signal $\Delta \theta$ of the order of $\Delta \theta = h$, where h is the amplitude of the gravitational wave, to a signal of the order $\Delta \theta = h\frac{L}{D}$, where D is the length of the arm and L is the length of the wire suspending the test mass. This configuration is a further evolution of the recent development of tiltmeters and balances with double suspended arms and interferometric read-out, where the main working principles are already tested. The expected sensitivity will be discussed with respect to the proposed parameters and the present technology.

gr-qc

Adaptive algorithms for low-latency cancellation of seismic Newtonian-noise at the Virgo gravitational-wave detector

A system was recently implemented in the Virgo detector to cancel noise in its data produced by seismic waves directly coupling with the suspended test masses through gravitational interaction. The data from seismometers are being filtered to produce a coherent estimate of the associated gravitational noise also known as Newtonian noise. The first implementation of the system uses a time-invariant (static) Wiener filter, which is the optimal filter for Newtonian-noise cancellation assuming that the noise is stationary. However, time variations in the form of transients and slow changes in correlations between sensors are possible and while time-variant filters are expected to cope with these variations better than a static Wiener filter, the question is what the limitations are of time-variant noise cancellation. In this study, we present a framework to study the performance limitations of time-variant noise cancellation filters and carry out a proof-of-concept with adaptive filters on seismic data at the Virgo site. We demonstrate that the adaptive filters, at least those with superior architecture, indeed significantly outperform the static Wiener filter with the residual noise remaining above the statistical error bound.

gr-qc

Angular control noise in Advanced Virgo and implications for the Einstein Telescope

With significantly improved sensitivity, the Einstein Telescope (ET), along with other upcoming gravitational wave detectors, will mark the beginning of precision gravitational wave astronomy. However, the pursuit of surpassing current detector capabilities requires careful consideration of technical constraints inherent in existing designs. The significant improvement of ET lies in the low-frequency range, where it anticipates a one million-fold increase in sensitivity compared to current detectors. Angular control noise is a primary limitation for LIGO detectors in this frequency range, originating from the need to maintain optical alignment. Given the expected improvements in ET's low-frequency range, precise assessment of angular control noise becomes crucial for achieving target sensitivity. To address this, we developed a model of the angular control system of Advanced Virgo, closely matching experimental data and providing a robust foundation for modeling future-generation detectors. Our model, for the first time, enables replication of the measured coupling level between angle and length. Additionally, our findings confirm that Virgo, unlike LIGO, is not constrained by alignment control noise, even if the detector were operating at full power.

astro-ph.IM

Design and implementation of a seismic Newtonian-noise cancellation system for the Virgo gravitational-wave detector

Terrestrial gravity perturbations caused by seismic fields produce the so-called Newtonian noise in gravitational-wave detectors, which is predicted to limit their sensitivity in the upcoming observing runs. In the past, this noise was seen as an infrastructural limitation, i.e., something that cannot be overcome without major investments to improve a detector's infrastructure. However, it is possible to have at least an indirect estimate of this noise by using the data from a large number of seismometers deployed around a detector's suspended test masses. The noise estimate can be subtracted from the gravitational-wave data; a process called Newtonian-noise cancellation (NNC). In this article, we present the design and implementation of the first NNC system at the Virgo detector as part of its AdV+ upgrade. It uses data from 110 vertical geophones deployed inside the Virgo buildings in optimized array configurations. We use a separate tiltmeter channel to test the pipeline in a proof-of-principle. The system has been running with good performance over months.

gr-qc

Cryogenic payloads for the Einstein Telescope -- Baseline design with heat extraction, suspension thermal noise modelling and sensitivity analyses

The Einstein Telescope (ET) is a third generation gravitational wave detector that includes a room-temperature high-frequency (ET-HF) and a cryogenic low-frequency laser interferometer (ET-LF). The cryogenic ET-LF is crucial for exploiting the full scientific potential of ET. We present a new baseline design for the cryogenic payload that is thermally and mechanically consistent and compatible with the design sensitivity curve of ET. The design includes two options for the heat extraction from the marionette, based on a monocrystalline high-conductivity marionette suspension fiber and a thin-wall titanium tube filled with static He-II, respectively. Following a detailed description of the design options and the suspension thermal noise (STN) modelling, we present the sensitivity curves of the two baseline designs, discuss the influence of various design parameters on the sensitivity of ET-LF and conclude with an outlook to future R&D activities.

astro-ph.IM

Quantum zero point electromagnetic energy difference between the superconducting and the normal phase in a HTc superconducting metal bulk sample

We provide a novel methodological approach to the estimate of the change of the Quantum Vacuum electromagnetic energy density in a High critical Temperature superconducting metal bulk sample, when it undergoes the transition in temperature, from the superconducting to the normal phase. The various contributions to the Casimir energy in the two phases are highlighted and compared. While the TM polarization of the vacuum mode allows for a macroscopic description of the superconducting transition, the changes in the TE vacuum mode induced by the superconductive correlations are introduced within a microscopic model, which does not explicitly take into account the anisotropic structure of the material.

cond-mat.supr-con

Tunnel configurations and seismic isolation optimization in underground gravitational wave detectors

Gravitational wave detectors like the Einstein Telescope will be built a few hundred meters under Earth's surface to reduce both direct seismic and Newtonian noise. Underground facilities must be designed to take full advantage of the shielding properties of the rock mass to maximize the detector's performance. A major issue with the Einstein Telescope design are the corner points, where caverns need to be excavated in stable, low permeability rock to host the sensitive measurement infrastructure. This paper proposes a new topology that moves the top stages of the seismic attenuation chains and Michelson beam re-combination in separate excavations far from the beam-line and equipment induced noise while the test mass mirrors remain in the main tunnels. Distributing the seismic attenuation chain components over multiple tunnel levels allows the use of arbitrarily long seismic attenuation chains that relegate the seismic noise at frequencies completely outside the low-frequency noise budget, thus keeping the door open for future Newtonian noise suppression methods. Separating the input-output and recombination optics of different detectors into separate caverns drastically improves the observatory detection efficiency and allows staged commissioning. The proposed scheme eliminates structural and instrumentation crowding while the reduced sizes of excavations require fewer support measures.

astro-ph.IM

External environmental noise influences on Virgo during O3

Sources of geophysical noise, such as wind, sea waves and earthquakes, can have an impact on gravitational wave interferometers causing sensitivity worsening and gaps in data taking. During the 1-year long O3 run (April 1st 2019 to March 27th 2020), the Virgo Collaboration collected a statistically significant dataset to study the response of the detector to a variety of environmental conditions. We used these data to correlate environmental parameters to global detector performance, such as observation range, duty cycle and control losses. Where possible, we identified weaknesses in the detector and we elaborated strategies to improve Virgo robustness against external disturbances for the next run O4, planned to start in summer 2022. In this article we present preliminary results of this study.

gr-qc

Site-selection criteria for the Einstein Telescope

The Einstein Telescope (ET) is a proposed next-generation, underground gravitational-wave (GW) detector to be based in Europe. It will provide about an order of magnitude sensitivity increase with respect to currently operating detectors, and furthermore, extend the observation band towards lower frequencies, i.e., down to about 3Hz. One of the first decisions that needs to be made is about the future ET site following an in-depth site characterization. Site evaluation and selection is a complicated process, which takes into account science, financial, political, and socio-economic criteria. In this paper, we provide an overview of the site-selection criteria for ET, provide a formalism to evaluate the direct impact of environmental noise on ET sensitivity, and outline the necessary elements of a site-characterization campaign.

physics.ins-det

Towards weighing the condensation energy to ascertain the Archimedes force of vacuum

The force exerted by the gravitational field on a Casimir cavity in terms of Archimedes force of vacuum is discussed, the force that can be tested against observation is identified, and it is shown that the present technology makes it possible to perform the first experimental tests. The use of suitable high-Tc superconductors as modulators of Archimedes force is motivated. The possibility is analyzed of using gravitational wave interferometers as detectors of the force, transported through an optical spring from the Archimedes vacuum force apparatus to the gravitational interferometer test masses to maintain the two systems well separated. The use of balances to actuate and detect the force is also analyzed, the different solutions are compared, and the most important experimental issues are discussed.

gr-qc

A sub nrad beam pointing monitoring and stabilization system for controlling input beam jitter in GW interferometers

In this paper a simple and very effective control system to monitor and suppress the beam jitter noise at the input of an optical system, called Beam Pointing Control (BPC) system, will be described showing the theoretical principle and an experimental demonstration for the application of large scale gravitational wave interferometers, in particular for the Advanced Virgo detector. For this purpose the requirements for the control accuracy and the sensing noise will be computed by taking into account the Advanced Virgo optical configuration and the outcomes will be compared with the experimental measurement obtained in the laboratory. The system has shown unprecedented performance in terms of control accuracy and sensing noise. The BPC system has achieved a control accuracy of ~ $10^{-8}$ rad for the tilt and ~ $10^{-7}$ m for the shift and a sensing noise of less than 1 nrad/$\sqrt{Hz}$ resulting compliant with the Advance Virgo gravitational wave interferometer requirements.

physics.optics