arXiv subjects

Paraskevas Kontis

Publications and source records attributed to Paraskevas Kontis.

14 recordsLinked to original sources

arXiv2025

Atomic-scale insights on grain boundary segregation in a cathode battery material

The grain boundary segregation of the Co-free pristine spinel LiNi0.5Mn1.5O4 cathode material has been studied by transmission electron microscopy and atom probe tomography. The segregation of Mn and the depletion of Ni at grain boundaries was observed by electron energy loss spectroscopy. These observations were also confirmed by atom probe tomography at other grain boundaries, which also revealed segregation of O and depletion of Li at grain boundaries. In addition, both methods revealed the occurrence of grain boundary segregation of Na, which is an impurity. Finally, segregation of O and Mn and a depletion of Li are also observed at dislocations. This observation has the potential to provide further support for the segregation behavior at the grain boundaries of this cathode material. These near-atomic-scale observations provide new insights that can be used to improve the synthesis and efficiency of Li-ion battery materials.

cond-mat.mtrl-sci↗

arXiv2024

Towards establishing best practice in the analysis of hydrogen and deuterium by atom probe tomography

As hydrogen is touted as a key player in the decarbonization of modern society, it is critical to enable quantitative H analysis at high spatial resolution, if possible at the atomic scale. Indeed, H has a known deleterious impact on the mechanical properties (strength, ductility, toughness) of most materials that can hinder their use as part of the infrastructure of a hydrogen-based economy. Enabling H mapping, including local hydrogen concentration analyses at specific microstructural features, is essential for understanding the multiple ways that H affect the properties of materials, including for instance embrittlement mechanisms and their synergies, but also spatial mapping and quantification of hydrogen isotopes is essential to accurately predict tritium inventory of future fusion power plants, ensuring their safe and efficient operation for example. Atom probe tomography (APT) has the intrinsic capabilities for detecting hydrogen (H), and deuterium (D), and in principle the capacity for performing quantitative mapping of H within a material's microstructure. Yet the accuracy and precision of H analysis by APT remain affected by the influence of residual hydrogen from the ultra-high vacuum chamber that can obscure the signal of H from within the material, along with a complex field evaporation behavior. The present article reports the essence of discussions at a focused workshop held at the Max-Planck Institute for Sustainable Materials in April 2024. The workshop was organized to pave the way to establishing best practices in reporting APT data for the analysis of H. We first summarize the key aspects of the intricacies of H analysis by APT and propose a path for better reporting of the relevant data to support interpretation of APT-based H analysis in materials.

cond-mat.mtrl-sci↗

arXiv2021

A cracking oxygen story: a new view of stress corrosion cracking in titanium alloys

Titanium alloys can suffer from halide-associated stress corrosion cracking at elevated temperatures e.g., in jet engines, where chlorides and Ti-oxide promote the cracking of water vapour in the gas stream, depositing embrittling species at the crack tip. Here we report, using isotopically-labelled experiments, that crack tips in an industrial Ti-6Al-2Sn-4Zr-6Mo alloy are strongly enriched (>5 at.%) in oxygen from the water vapour, far greater than the amounts (0.25 at.%) required to embrittle the material. Surprisingly, relatively little hydrogen (deuterium) is measured, despite careful preparation and analysis. Therefore, we suggest that a combined effect of O and H leads to cracking, with O playing a vital role, since it is well-known to cause embrittlement of the alloy. In contrast it appears that in alpha+beta Ti alloys, it may be that H may drain away into the bulk owing to its high solubility in beta-Ti, rather than being retained in the stress field of the crack tip. Therefore, whilst hydrides may form on the fracture surface, hydrogen ingress might not be the only plausible mechanism of embrittlement of the underlying matrix. This possibility challenges decades of understanding of stress-corrosion cracking as being related solely to the hydrogen enhanced localised plasticity (HELP) mechanism, which explains why H-doped Ti alloys are embrittled. This would change the perspective on stress corrosion embrittlement away from a focus purely on hydrogen to also consider the ingress of O originating from the water vapour, insights critical for designing corrosion resistant materials.

cond-mat.mtrl-sci↗

arXiv2021

Nanoscale characterisation of hydrides and secondary phase particles in Zircaloy-4

The interaction of hydrogen and metals continues to be industrially relevant and is a critical part of creating and supporting a safety case for nuclear reactor operation. In the present work, we explore hydrogen storage and hydride formation in a zirconium alloy. We characterise the structure and interfaces of fine scale hydrides using scanning transmission electron microscopy (STEM) including energy dispersive spectroscopy (EDS/EDX), electron energy loss spectroscopy (EELS), and high-resolution STEM. Chemical characterisation is supported further with atom probe tomography (APT). Samples were prepared with cryo-focussed ion beam machining (cryo-FIB) and contain hydrides in α-Zr matrix and hydrides associated with one FeCrZr secondary phase particle (SPP). Major findings include characterisation of different interface planes based upon the size of the hydrides and chemical redistribution of solute ahead of the hydride-metal interface. We also find significant (up to 6 at%) hydrogen retained in solution within the zirconium matrix and show a hydride with only 17 at% hydrogen, which is well below that of a ξ-phase stoichiometry suggesting it is an embryonic hydride. These findings help us understand the distribution of hydrogen and the nanoscale morphology of hydrides, which may influence the lifetime of zirconium-based nuclear fuel cladding.

cond-mat.mtrl-sci↗

arXiv2021

On the role of boron, carbon and zirconium on hot cracking and creep resistance of additively manufactured polycrystalline superalloys

We investigate the hot cracking susceptibility and creep resistance of three versions of a nickel-based superalloy with different contents of boron, carbon and zirconium fabricated by laser powder bed fusion. Crack-free and creep resistant components are achieved for alloys with boron, carbon and no zirconium. We then rationalize this result by evaluating how boron, carbon and zirconium are distributed at grain boundaries in the as-built and heat-treated microstructures of an alloy containing all these elements. Observations are conducted by scanning and transmission electron microscopy, and atom probe tomography. In the as-built microstructure, boron, carbon and zirconium segregate at high-angle grain boundaries as a result of solute partitioning to the liquid and limited solid-state diffusion during solidification and cooling. After heat-treatment, the amount of boron and carbon segregating at grain boundaries increases significantly. In contrast, zirconium is not found at grain boundaries but it partitions at the gamma' precipitates formed during the heat treatment. The presence of zirconium at grain boundaries in the as-built condition is known to be susceptible to enhance hot cracking, while its absence in the heat-treated microstructure strongly suggests that this element has no major effect on the creep resistance. Based on our observations, we propose alloy design guidelines to at the same time avoid hot cracking during fabrication and achieve the required creep performance after heat-treatment.

cond-mat.mtrl-sci↗

arXiv2021

Mechanisms of Ti3Al precipitation in hcp alpha-Ti

Nucleation and growth of Ti$_3$Al \textalpha{}$_2$ ordered domains in \textalpha{}-Ti--Al--X alloys were characterised using a combination of transmission electron microscopy, atom probe tomography and small angle X-ray scattering. Model alloys based on Ti--7Al~(wt.\%) and containing O, V and Mo were aged at \SI{550}{\celsius} for times up to \SI{120}{\day} and the resulting precipitate dispersions were observed at intermediate points. Precipitates grew to around \SI{30}{\nano\metre} in size, with a volume fraction of 6--10\% depending on tertiary solutes. Interstitial O was found to increase the equilibrium volume fraction of \textalpha{}$_2$, while V and Mo showed relatively little influence. Addition of any of the solutes in this study, but most prominently Mo, was found to increase nucleation density and decrease precipitate size and possibly coarsening rate. Coarsening can be described by the Lifshitz-Slyozov-Wagner model, suggesting a matrix diffusion-controlled coarsening mechanism (rather than control by interfacial coherency). Solutionising temperature was found to affect nucleation number density with an activation energy of $E_{\mathrm{f}} = 1.5\pm{}0.4$~eV, supporting the hypothesis that vacancy concentration affects \textalpha{}$_2$ nucleation. The observation that all solutes increase nucleation number density is also consistent with a vacancy-controlled nucleation mechanism.

cond-mat.mtrl-sci↗

arXiv2020

Enhanced creep performance in a polycrystalline superalloy driven by atomic-scale phase transformation along planar faults

Predicting the mechanical failure of parts in service requires understanding their deformation behavior, and associated dynamic microstructural evolution up to the near-atomic scale. Solutes are known to interact with defects generated by plastic deformation, thereby affecting their displacement throughout the microstructure and hence the material mechanical response to solicitation. This effect is studied here in a polycrystalline Ni-based superalloy with two different Nb contents that lead to a significant change in their creep lifetime. Creep testing at 750C and 600 MPa shows that the high-Nb alloy performs better in terms of creep strain rate. Considering the similar initial microstructures, the difference in mechanical behavior is attributed to a phase transformation that occurs along planar faults, controlled by the different types of stacking faults and alloy composition. Electron channeling contrast imaging reveals the presence of stacking faults in both alloys. Microtwinning is observed only in the low-Nb alloy, rationalizing in part the higher creep strain rate. In the high-Nb alloy, atom probe tomography evidences two different types of stacking faults based on their partitioning behavior. Superlattice intrinsic stacking faults (SISF) were found enriched in Nb, Co, Cr and Mo while only Nb and Co was segregated at superlattice extrinsic stacking faults. Based on their composition, a local phase transformation occurring along the faults is suggested, resulting in slower creep strain rate in the high-Nb alloy. In comparison, mainly SISF enriched in Co, Cr, Nb and Mo were found in the low-Nb alloy. Following the results presented here, and those available in the literature, an atomic-scale driven alloy design approach that controls and promotes local phase transformation along planar faults at 750C is proposed, aiming to design superalloys with enhanced creep resistance.

cond-mat.mtrl-sci↗

arXiv2020

Spinodal decomposition versus classical gamma-prime nucleation in a nickel-base superalloy powder: An in-situ neutron diffraction and atomic-scale analysis

Contemporary powder-based polycrystalline nickel-base superalloys inherit microstructures and properties that are heavily determined by the thermo-mechanical treatments during processing. Here, the influence of a thermal exposure alone to an alloy powder is studied to elucidate the controlling formation mechanisms of the strengthening precipitates using a combination of atom probe tomography and in-situ neutron diffraction. The initial powder comprised a single-phase supersaturated gamma only; from this, the evolution of gamma-prime volume fraction and lattice misfit was assessed. The initial powder notably possessed elemental segregation of Cr and Co and elemental repulsion between Ni, Al and Ti with Cr; here proposed to be a precursor for subsequent gamma to gamma-prime phase transformations. Subsolvus heat treatments yielded a unimodal gamma-prime distribution, formed during heating, with evidence supporting its formation to be via spinodal decomposition. A supersolvus heat treatment led to the formation of this same gamma-prime population during heating, but dissolves as the temperature increases further. The gamma-prime then reprecipitates as a multimodal population during cooling, here forming by classical nucleation and growth. Atom probe characterisation provided intriguing precipitate characteristics, including clear differences in chemistry and microstructure, depending on whether the gamma-prime formed during heating or cooling.

cond-mat.mtrl-sci↗

arXiv2020

On the coarsening mechanism and deformation of borides under annealing and creep in a polycrystalline superalloy

We have investigated the coarsening mechanism of intergranular Cr-rich M2B borides after creep and annealing at 850C for approximately 3000 hours in a polycrystalline nickel-based superalloy. Borides were found to be coarser after creep, with measured thicknesses in the range of 800-1100nm, compared to borides annealed in the absence of external applied load (400-600nm). The borides had a thickness of 100-200nm before exposure at 850C. Transmission electron microscopy revealed that coarsened borides have either the tetragonal I4/mcm structure, or the orthorhombic Fddd, with those two structures coexisting in a single particle. The presence of a very high density of planar faults is systematically observed within the coarsened borides. The faults were correlated with chemical fluctuations of B and Cr, revealed by atom probe tomography. Our results allow us to suggest that borides coarsen by an epitaxy-like mechanism. In addition, partitioning of Ni and Co was observed at dislocations within the borides after creep providing insights into the deformation of borides. Consequences of coarsened intergranular borides on the creep performance of polycrystalline superalloys are discussed.

cond-mat.mtrl-sci↗

arXiv2019

Atomic-scale grain boundary engineering to overcome hot-cracking in additively-manufactured superalloys

There are still debates regarding the mechanisms that lead to hot cracking in parts build by additive manufacturing (AM) of non-weldable Ni-based superalloys. This lack of in-depth understanding of the root causes of hot cracking is an impediment to designing engineering parts for safety-critical applications. Here, we deploy a near-atomic-scale approach to investigate the details of the compositional decoration of grain boundaries in the coarse-grained, columnar microstructure in parts built from a non-weldable Ni-based superalloy by selective electron-beam melting. The progressive enrichment in Cr, Mo and B at grain boundaries over the course of the AM-typical successive solidification and remelting events, accompanied by solid-state diffusion, causes grain boundary segregation induced liquation. This observation is consistent with thermodynamic calculations. We demonstrate that by adjusting build parameters to obtain a fine-grained equiaxed or a columnar microstructure with grain width smaller than 100 $μ$m enables to avoid cracking, despite strong grain boundary segregation. We find that the spread of critical solutes to a higher total interfacial area, combined with lower thermal stresses, helps to suppress interfacial liquation.

cond-mat.mtrl-sci↗

arXiv2019

Quantification challenges for atom probe tomography of hydrogen and deuterium in Zircaloy-4

Analysis and understanding of the role of hydrogen in metals is a significant challenge for the future of materials science, and this is a clear objective of recent work in the atom probe tomography (APT) community. Isotopic marking by deuteration has often been proposed as the preferred route to enable quantification of hydrogen by APT. Zircaloy-4 was charged electrochemically with hydrogen and deuterium under the same conditions to form large hydrides and deuterides. Our results from a Zr hydride and a Zr deuteride highlight challenges associated to accurate quantification of hydrogen and deuterium, in particular associated to the overlap of peaks at low mass-to-charge ratio and of hydrogen/deuterium containing molecular ions. We discuss possible ways to ensure that appropriate information is extracted from APT analysis of hydrogen in a zirconium alloy systems that is important for nuclear power.

cond-mat.mtrl-sci↗

arXiv2019

Influence of composition and precipitation evolution on damage at grain boundaries in a crept polycrystalline Ni-based superalloy

The microstructural and compositional evolution of intergranular carbides and borides prior to and after creep deformation at 850 $^\circ$C in a polycrystalline nickel-based superalloy was studied. Primary MC carbides, enveloped within intergranular $\rm γ'$ layers, decomposed resulting in the formation of layers of the undesirable $\rm η$ phase. These layers have a composition corresponding to Ni$_{3}$Ta as measured by atom probe tomography and their structure is consistent with the D0$_{24}$ hexagonal structure as revealed by transmission electron microscopy. Electron backscattered diffraction reveals that they assume various misorientations with regard to the adjacent grains. As a consequence, these layers act as brittle recrystallized zones and crack initiation sites. The composition of the MC carbides after creep was altered substantially, with the Ta content decreasing and the Hf and Zr contents increasing, suggesting a beneficial effect of Hf and Zr additions on the stability of MC carbides. By contrast, $\rm M_{5}B_3$ borides were found to be microstructurally stable after creep and without substantial compositional changes. Borides at 850 $^\circ$C were found to coarsen, resulting in some cases into $\rm γ'$-depleted zones, where, however, no cracks were observed. The major consequences of secondary phases on the microstructural stability of superalloys during the design of new polycrystalline superalloys are discussed.

cond-mat.mtrl-sci↗

arXiv2018

On the segregation of Re at dislocations in the γ' phase of Ni-based single crystal superalloys

We report evidence of Re and Mo segregation (up to 2.6 at.% and 1 at.%) along with Cr and Co to the dislocations inside of γ' precipitates in a second generation Ni-based single crystal superalloy, after creep deformation at 750°C under an applied stress of 800 MPa. The observed segregation effects can be rationalized through bridging the solute partitioning behavior across the γ/γ' interface and the pipe diffusion mechanism along the core of the dislocation line. This understanding can provide new insights enabling improved alloy design.

cond-mat.mtrl-sci↗

arXiv2018

The Laplace project: an integrated suite for correlative atom probe tomography and electron microscopy under cryogenic and UHV conditions

We present sample transfer instrumentation and integrated protocols for the preparation and correlative characterization of environmentally-sensitive materials by both atom probe tomography and electron microscopy. Ultra-high vacuum cryogenic suitcases allow specimen transfer between preparation, processing and several imaging platforms without exposure to atmospheric contamination. For expedient transfers, we installed a fast-docking station equipped with a cryogenic pump upon three systems; two atom probes, a scanning electron microscope / Xe-plasma focused ion beam and a N$_2$-atmosphere glovebox. We also installed a plasma FIB with a solid-state cooling stage to reduce beam damage and contamination, through reducing chemical activity and with the cryogenic components as passive cryogenic traps. We demonstrate the efficacy of the new laboratory protocols by the successful preparation and transfer of two highly contamination- and temperature-sensitive samples - water and ice. Analysing pure magnesium atom probe data, we show that surface oxidation can be effectively suppressed using an entirely cryogenic protocol (during specimen preparation and during transfer). Starting with the cryogenically-cooled plasma FIB, we also prepared and transferred frozen ice samples while avoiding significant melting or sublimation, suggesting that we may be able to measure the nanostructure of other normally-liquid or soft materials. Isolated cryogenic protocols within the N$_2$ glove box demonstrate the absence of ice condensation suggesting that environmental control can commence from fabrication until atom probe analysis.

cond-mat.mtrl-sci↗