Searcharxiv⌕ Search

arXiv subjects

Peter Fritschel

Publications and source records attributed to Peter Fritschel.

At least 19 recordsLinked to original sources
arXiv2026

Loss-tolerant hybrid metasurface mirror for reducing coating Brownian noise in precision optical cavities

We propose a hybrid mirror design that places an embedded metasurface beneath a Bragg reflector, combining the low coating Brownian noise of metasurface mirrors with the low optical loss of conventional multilayer coatings. Unlike previous hybrid designs, which place the metasurface at the input surface, our design positions it below the Bragg stack, reducing the optical field incident on the loss-prone resonant layer. For a design operating at 1064 nm, we show that this reduces absorption from 24 ppm for a bare metasurface to 7 ppm for the hybrid. We introduce a general method for calculating the coating Brownian noise of hybrid metasurface-multilayer mirrors at arbitrary coupling strength, extending prior methods to coherently combine a beam-scale mean-field contribution with the periodic, sub-wavelength-scale response of the metasurface. Applying this to our design, we find a reduction in Brownian noise amplitude spectral density relative to an equivalent-reflectance Bragg mirror by a factor of 1.6. Finally, we show that this design has higher angular tolerance than a bare metasurface mirror, maintaining higher reflectance over an angular range of 1 degree. This work provides a practical path towards incorporating low-noise metasurface mirrors into precision optical cavities, while minimizing optical loss and angular sensitivity.

physics.optics↗
arXiv2026

Coating-free monolithic fused silica resonator via total internal reflection for precision laser stabilization

Brownian noise in the thin-film mirror coatings of optical reference cavities is a fundamental limitation in precision metrology, including gravitational-wave detectors and optical atomic clocks. We demonstrate a monolithic fused silica resonator that eliminates the use of thin-film coatings by operating via total internal reflection (TIR), achieving a finesse of 1225 and an optical mode volume of \qty{50}{mm^3}. To our knowledge, this is the largest mode volume reported for any coating-free monolithic resonator, comparable to state-of-the-art reference cavities. We use the cavity to frequency-stabilize an Nd:YAG laser, and demonstrate its application to precision metrology by operating it in a passive ring gyroscope configuration. This platform circumvents the dominant noise source of conventional reference cavities and provides a pathway toward cryogenic silicon TIR resonators that could surpass current frequency stabilization limits.

physics.optics↗
arXiv2026

Extending Ground-Based Gravitational-Wave Sensitivity to 5 Hz

Extending the sensitivity of terrestrial gravitational-wave detectors below 20 Hz is a long-standing challenge, limited by ground motion and inertial sensing noise. In this letter, we demonstrate ultra-high-vacuum compatible inertial isolation and position sensing technologies that achieve active platform stabilization down to 10 mHz. Our laser position sensors reach a sub-pm/$\sqrt{\rm Hz}$ sensitivity above 10 mHz, independent of the input light polarization, representing a 100-fold improvement over the current LIGO position sensors. In addition, our inertial sensors provide at least a factor of 5 improvement in low-frequency sensitivity compared to state-of-the-art commercial seismometers. We integrate these technologies into a LIGO-like interferometer model and predict a low-frequency sensitivity improvement of up to an order of magnitude at 10 Hz, with enhanced linearity and calibration stability. This extension increases the detection horizon for intermediate-mass black hole binaries of mass $10^3 M_\odot$ by a factor of 3. Our results provide the first experimental demonstration of a practical pathway to sub-10 Hz operation of terrestrial gravitational-wave detectors and establish key technologies for next-generation observatories such as Cosmic Explorer and Einstein Telescope.

astro-ph.IM↗
arXiv2024

Squeezing the quantum noise of a gravitational-wave detector below the standard quantum limit

Precision measurements of space and time, like those made by the detectors of the Laser Interferometer Gravitational-wave Observatory (LIGO), are often confronted with fundamental limitations imposed by quantum mechanics. The Heisenberg uncertainty principle dictates that the position and momentum of an object cannot both be precisely measured, giving rise to an apparent limitation called the Standard Quantum Limit (SQL). Reducing quantum noise below the SQL in gravitational-wave detectors, where photons are used to continuously measure the positions of freely falling mirrors, has been an active area of research for decades. Here we show how the LIGO A+ upgrade reduced the detectors' quantum noise below the SQL by up to 3 dB while achieving a broadband sensitivity improvement, more than two decades after this possibility was first presented.

gr-qc↗
arXiv2024

Characterizing Gravitational Wave Detector Networks: From A$^\sharp$ to Cosmic Explorer

Gravitational-wave observations by the Laser Interferometer Gravitational-Wave Observatory (LIGO) and Virgo have provided us a new tool to explore the Universe on all scales from nuclear physics to the cosmos and have the massive potential to further impact fundamental physics, astrophysics, and cosmology for decades to come. In this paper we have studied the science capabilities of a network of LIGO detectors when they reach their best possible sensitivity, called A#, given the infrastructure in which they exist and a new generation of observatories that are factor of 10 to 100 times more sensitive (depending on the frequency), in particular a pair of L-shaped Cosmic Explorer observatories (one 40 km and one 20 km arm length) in the US and the triangular Einstein Telescope with 10 km arms in Europe. The presence of one or two A# observatories in a network containing two or one next generation observatories, respectively, will provide good localization capabilities for facilitating multimessenger astronomy and precision measurement of the Hubble parameter. Two Cosmic Explorer observatories are indispensable for achieving precise localization of binary neutron star events, facilitating detection of electromagnetic counterparts and transforming multimessenger astronomy. Their combined operation is even more important in the detection and localization of high-redshift sources, such as binary neutron stars, beyond the star-formation peak, and primordial black hole mergers, which may occur roughly 100 million years after the Big Bang. The addition of the Einstein Telescope to a network of two Cosmic Explorer observatories is critical for accomplishing all the identified science metrics. For most metrics the triple network of next generation terrestrial observatories are a factor 100 better than what can be accomplished by a network of three A# observatories.

gr-qc↗
arXiv2023

Cosmic Explorer: A Submission to the NSF MPSAC ngGW Subcommittee

Gravitational-wave astronomy has revolutionized humanity's view of the universe, a revolution driven by observations that no other field can make. This white paper describes an observatory that builds on decades of investment by the National Science Foundation and that will drive discovery for decades to come: Cosmic Explorer. Major discoveries in astronomy are driven by three related improvements: better sensitivity, higher precision, and opening new observational windows. Cosmic Explorer promises all three and will deliver an order-of-magnitude greater sensitivity than LIGO. Cosmic Explorer will push the gravitational-wave frontier to almost the edge of the observable universe using technologies that have been proven by LIGO during its development. With the unprecedented sensitivity that only a new facility can deliver, Cosmic Explorer will make discoveries that cannot yet be anticipated, especially since gravitational waves are both synergistic with electromagnetic observations and can reach into regions of the universe that electromagnetic observations cannot explore. With Cosmic Explorer, scientists can use the universe as a laboratory to test the laws of physics and study the nature of matter. Cosmic Explorer allows the United States to continue its leading role in gravitational-wave science and the international network of next-generation observatories. With its extraordinary discovery potential, Cosmic Explorer will deliver revolutionary observations across astronomy, physics, and cosmology including: Black Holes and Neutron Stars Throughout Cosmic Time, Multi-Messenger Astrophysics and Dynamics of Dense Matter, New Probes of Extreme Astrophysics, Fundamental Physics and Precision Cosmology, Dark Matter and the Early Universe.

astro-ph.IM↗
arXiv2022

Snowmass2021 Cosmic Frontier White Paper: Future Gravitational-Wave Detector Facilities

The next generation of gravitational-wave observatories can explore a wide range of fundamental physics phenomena throughout the history of the universe. These phenomena include access to the universe's binary black hole population throughout cosmic time, to the universe's expansion history independent of the cosmic distance ladders, to stochastic gravitational-waves from early-universe phase transitions, to warped space-time in the strong-field and high-velocity limit, to the equation of state of nuclear matter at neutron star and post-merger densities, and to dark matter candidates through their interaction in extreme astrophysical environments or their interaction with the detector itself. We present the gravitational-wave detector concepts than can drive the future of gravitational-wave astrophysics. We summarize the status of the necessary technology, and the research needed to be able to build these observatories in the 2030s.

gr-qc↗
arXiv2022

Next Generation Observatories -- Report from the Dawn VI Workshop; October 5-7 2021

The workshop Dawn VI: Next Generation Observatories took place online over three days, 5-7 October, 2021. More than 200 physicists and astronomers attended to contribute to, and learn from, a discussion of next-generation ground-based gravitational-wave detectors. The program was centered on the next generation of ground-based gravitational-wave observatories and their synergy with the greater landscape of scientific observatories of the 2030s. Cosmic Explorer (CE), a concept developed with US National Science Foundation support, was a particular focus; Einstein Telescope (ET), the European next generation concept, is an important complement and partner in forming a network. The concluding summary of the meeting expressed the sentiment that the observational science accessible to CE and ET, also in combination with data from other non-GW observatories, will stimulate a very broad community of analysts and yield insights which are exciting given the access to GWs from the entire universe. The need, and desire, for closer collaboration between ET and CE was expressed; a three-detector network is optimal for delivering much of the science. The science opportunities afforded by CE and ET are broad and compelling, impacting a wide range of disciplines in physics and high energy astrophysics. There was a consensus that CE is a concept that can deliver the promised science. A strong endorsement of Cosmic Explorer, as described in the CE Horizon Study, is a primary outcome of DAWN VI.

astro-ph.IM↗
arXiv2022

Piezo-deformable Mirrors for Active Mode Matching in Advanced LIGO

The detectors of the laser interferometer gravitational-wave observatory (LIGO) are broadly limited by the quantum noise and rely on the injection of squeezed states of light to achieve their full sensitivity. Squeezing improvement is limited by mode mismatch between the elements of the squeezer and the interferometer. In the current LIGO detectors, there is no way to actively mitigate this mode mismatch. This paper presents a new deformable mirror for wavefront control that meets the active mode matching requirements of advanced LIGO. The active element is a piezo-electric transducer, which actuates on the radius of curvature of a 5 mm thick mirror via an axisymmetric flexure. The operating range of the deformable mirror is 120+-8 mD in vacuum, with an additional 200 mD adjustment range accessible out of vacuum. The scattering into higher-order modes is measured to be <0.2% over the nominal beam radius. These piezo-deformable mirrors meet the stringent noise and vacuum requirements of advanced LIGO and will be used for the next observing run (O4) to control the mode-matching between the squeezer and the interferometer.

astro-ph.IM↗
arXiv2021

Gravitational-wave physics with Cosmic Explorer: limits to low-frequency sensitivity

Cosmic Explorer (CE) is a next-generation ground-based gravitational-wave observatory concept, envisioned to begin operation in the 2030s, and expected to be capable of observing binary neutron star and black hole mergers back to the time of the first stars. Cosmic Explorer's sensitive band will extend below 10 Hz, where the design is predominantly limited by geophysical, thermal, and quantum noises. In this work, thermal, seismic, gravity-gradient, quantum, residual gas, scattered-light, and servo-control noises are analyzed in order to motivate facility and vacuum system design requirements, potential test mass suspensions, Newtonian noise reduction strategies, improved inertial sensors, and cryogenic control requirements. Our analysis shows that with improved technologies, Cosmic Explorer can deliver a strain sensitivity better than $10^{-23}/\mathrm{Hz}^{1/2}$ down to 5 Hz. Our work refines and extends previous analysis of the Cosmic Explorer concept and outlines the key research areas needed to make this observatory a reality.

gr-qc↗
arXiv2021

Point absorbers in Advanced LIGO

Small, highly absorbing points are randomly present on the surfaces of the main interferometer optics in Advanced LIGO. The resulting nano-meter scale thermo-elastic deformations and substrate lenses from these micron-scale absorbers significantly reduces the sensitivity of the interferometer directly though a reduction in the power-recycling gain and indirect interactions with the feedback control system. We review the expected surface deformation from point absorbers and provide a pedagogical description of the impact on power build-up in second generation gravitational wave detectors (dual-recycled Fabry-Perot Michelson interferometers). This analysis predicts that the power-dependent reduction in interferometer performance will significantly degrade maximum stored power by up to 50% and hence, limit GW sensitivity, but suggests system wide corrections that can be implemented in current and future GW detectors. This is particularly pressing given that future GW detectors call for an order of magnitude more stored power than currently used in Advanced LIGO in Observing Run 3. We briefly review strategies to mitigate the effects of point absorbers in current and future GW wave detectors to maximize the success of these enterprises.

physics.ins-det↗
arXiv2019

The US Program in Ground-Based Gravitational Wave Science: Contribution from the LIGO Laboratory

Recent gravitational-wave observations from the LIGO and Virgo observatories have brought a sense of great excitement to scientists and citizens the world over. Since September 2015,10 binary black hole coalescences and one binary neutron star coalescence have been observed. They have provided remarkable, revolutionary insight into the "gravitational Universe" and have greatly extended the field of multi-messenger astronomy. At present, Advanced LIGO can see binary black hole coalescences out to redshift 0.6 and binary neutron star coalescences to redshift 0.05. This probes only a very small fraction of the volume of the observable Universe. However, current technologies can be extended to construct "$3^\mathrm{rd}$ Generation" (3G) gravitational-wave observatories that would extend our reach to the very edge of the observable Universe. The event rates over such a large volume would be in the hundreds of thousands per year (i.e.tens per hour). Such 3G detectors would have a 10-fold improvement in strain sensitivity over the current generation of instruments, yielding signal-to-noise ratios of 1000 for events like those already seen. Several concepts are being studied for which engineering studies and reliable cost estimates will be developed in the next 5 years.

astro-ph.IM↗
arXiv2019

A compact actively damped vibration isolation platform for optical experiments in ultra-high vacuum

We present a tabletop six-axis vibration isolation system, compatible with Ultra-High Vacuum (UHV), which is actively damped and provides 25 dB of isolation at 10 Hz and 65 dB at 100 Hz. While this isolation platform has been primarily designed to support optics in the Laser Interferometer Gravitational-Wave Observatory (LIGO) detectors, it is suitable for a variety of applications. The system has been engineered to facilitate the construction and assembly process, while minimizing cost. The platform provides passive isolation for six degrees of freedom using a combination of vertical springs and horizontal pendula. It is instrumented with voice-coil actuators and optical shadow sensors to damp the resonances. All materials are compatible with stringent vacuum requirements. Thanks to its architecture, the system's footprint can be adapted to meet spatial requirements, while maximizing the dimensions of the optical table. Three units are currently operating for LIGO. We present the design of the system, controls principle, and experimental results.

physics.ins-det↗
arXiv2018

Relativistic coupling of phase and amplitude noise in optical interferometry

Extraneous motion of optical elements in an interferometer lead to excess noise. Typically, fluctuations in the effective path length lead to phase noise, while beam-pointing leads to apparent amplitude noise. For a transmissive optic moving along the optical axis, neither effect should exist. However, relativity of motion suggests that even in this case, small corrections of order $v/c$ ($v$ the velocity of the optic), give rise to phase and amplitude noise on the light. Here we calculate the effect of this relativistic mechanism of noise coupling, and discuss when such an effect would limit the sensitivity of optical interferometers.

physics.ins-det↗
arXiv2017

Damping parametric instabilities in future gravitational wave detectors by means of electrostatic actuators

It has been suggested that the next generation of interferometric gravitational wave detectors may observe spontaneously excited parametric oscillatory instabilities. We present a method of actively suppressing any such instability through application of electrostatic forces to the interferometers' test masses. Using numerical methods we quantify the actuation force required to damp candidate instabilities and find that such forces are readily achievable. Our predictions are subsequently verified experimentally using prototype Advanced LIGO hardware, conclusively demonstrating the effectiveness of our approach.

physics.ins-det↗
arXiv2016

First Demonstration of Electrostatic Damping of Parametric Instability at Advanced LIGO

Interferometric gravitational wave detectors operate with high optical power in their arms in order to achieve high shot-noise limited strain sensitivity. A significant limitation to increasing the optical power is the phenomenon of three-mode parametric instabilities, in which the laser field in the arm cavities is scattered into higher order optical modes by acoustic modes of the cavity mirrors. The optical modes can further drive the acoustic modes via radiation pressure, potentially producing an exponential buildup. One proposed technique to stabilize parametric instability is active damping of acoustic modes. We report here the first demonstration of damping a parametrically unstable mode using active feedback forces on the cavity mirror. A 15,538 Hz mode that grew exponentially with a time constant of 182 sec was damped using electro-static actuation, with a resulting decay time constant of 23 sec. An average control force of 0.03 nNrms was required to maintain the acoustic mode at its minimum amplitude.

physics.ins-det↗
arXiv2015

Observation of Parametric Instability in Advanced LIGO

Parametric instabilities have long been studied as a potentially limiting effect in high-power interferometric gravitational wave detectors. Until now, however, these instabilities have never been observed in a kilometer-scale interferometer. In this work we describe the first observation of parametric instability in an Advanced LIGO detector, and the means by which it has been removed as a barrier to progress.

astro-ph.IM↗