arXiv subjects

Peter Stephan

Publications and source records attributed to Peter Stephan.

6 recordsLinked to original sources

arXiv2026

Derivation of the Thermal Conductivity in a Latent Thermal Energy Storage Unit for Use in Simplified System Models

Latent Thermal Energy Storages (LTES) can store thermal energy in a narrow temperature range. Therefore, they are favorable for integration into Rankine-based Carnot Batteries. For the design of such systems, simulations based on accurate models are desirable. However, physical phenomena such as natural convection in LTES units cannot be modeled directly in transient system models. Simplified models are required. Therefore, the objective of this work is to derive simplified LTES unit models for use in system models. In transient simulations the state of charge of the LTES influences its temperature profile. The temperature profile depends on the geometry of the LTES unit. Therefore, the geometry must be considered to model the transient behavior of an LTES unit. The LTES unit under investigation has a shell and tube heat exchanger structure. The phase change material (PCM) is located between the hexagonal fins and in the space between the finned tubes. Aluminum fins are used. They have a high thermal conductivity and thus compensate for the low thermal conductivity of the sodium nitrate used as PCM. The interaction between fins and PCM is complex. Therefore, a numerical approach can be used to gain insight into the behavior of the LTES unit. To transfer the results of a complex model to a simplified model where fins and PCM are not considered individually, the effective thermal conductivity of a single finned tube can be used to approximate the performance of the LTES unit. In this study, a model of a section with a single finned tube is developed using the COMSOL software. The effective thermal conductivity of the system is determined by varying the effective thermal conductivity in a simplified model and comparing the results with reference cases based on a complex modeling approach. The results can serve as model input for simplified system models of Carnot Batteries, among others.

eess.SY↗

arXiv2023

Heat transport during drop impact onto a heated wall covered with an electrospun nanofiber mat: The influence of wall superheat, impact velocity, and mat thickness

Nanofiber surface coating is a promising method for the enhancement of heat transfer during spray cooling. In the present work, the drop dynamics as well as local and overall heat transfer during single drop impact onto a heated wall covered with a nanofiber mat are investigated to obtain insight into the mechanisms governing the heat transport enhancement. The influence of wall superheat, drop impact velocity, and mat thickness on the hydrodynamics and heat transfer from the heated wall to the fluid is studied. Polyacrylonitrile (PAN) was electrospun on a heater surface to manufacture the nanofiber mat coatings. The experiments were conducted inside a temperature-controlled test cell with a pure vapor atmosphere maintained with refrigerant FC-72. The temperature field at the solid-fluid interface was observed with a high-speed infrared camera, and the heat flux field was derived by solving a three-dimensional transient heat conduction equation within the substrate. The presence of the nanofiber mat on the heater surface suppresses the drop receding phase due to the pinning of the contact line at the end of the spreading phase. Two different scenarios are observed depending on the wall superheat and drop impact velocity: scenario (I), in which the liquid drop penetrated the porous nanofiber mat and touches the heater surface; and scenario (II) in which the vapor produced inside the pores of the nanofiber mat prevented the liquid drop from touching the heater surface. At a certain point in time after impact, the energy transferred from the nanofiber-coated surface to the liquid exceeds that of the uncovered heater owing to the larger drop footprint. If scenario (I) occurs, then the total transported heat increases significantly compared with the drop impact on a bare substrate.

physics.flu-dyn↗

arXiv2023

Experimental Study of Condensation of Water on Polydimethylsiloxane-Coated Copper Surfaces

Modification of surfaces to enable dropwise condensation is a promising approach for achieving high condensation rates. In this work, we present an experimental study on condensation of water on copper surfaces coated with an ultrathin, 5 nm - 10 nm thick polydimethylsiloxane (PDMS) layer. This hydrophobic coating possesses a very low thermal resistance, which in combination with copper substrate enables achieving high condensation rates in heat transfer applications. The PDMS-coated copper substrates have been fabricated with a newly developed method, which involves turning, sanding, polishing, oxidation, and polymer coating steps. The measured static contact angle was 110{\deg}, and a the contact angle hysteresis was 2{\deg}. The achieved very low hysteresis is advantageous for promoting dropwise condensation. The surface showed no ageing effects during 100 repetitions of advancing and receding contact angle (ARCA) measurements. Condensation heat transfer on uncoated and PDMS-coated copper surfaces surfaces has been studied experimentally in a saturated water vapor atmosphere at 60{\deg}C. An enhancement factor for heat flux and heat transfer coefficient of up to 1.6 was found on PDMS-coated copper surfaces compared to uncoated surfaces, which decreased to 1.1 on second and third day of condensation operation. Images of the condensation surface were recorded while conducting condensation experiments and post processed to evaluate drop departure diameter and frequency of drop sweeping events. It has been shown that the behavior of the heat transfer coefficient correlates with the frequency of the sweeping events.

physics.flu-dyn↗

arXiv2023

Studying Macro- and Mesoscopic Wetting Dynamics of a Spreading Oil Droplet Using Multiple Wavelength Interferometry

In this study we present an interferometric technique based on multiple wavelengths to capture the transient free surface contour of nanoliter drops spreading on a wettable surface, in particular close to the three-phase contact line. Various data analysis procedures are evaluated in terms of error and noise sensitivity. The technique allows an unambiguous determination of the local liquid film thickness for optical path differences up to $\Delta s \approx 3.19\,\mathrm{\mu m}$ without the need of a known reference height. Film thicknesses as low as $0.1\,\mathrm{\mu m}$ can be measured with the present optical configuration. The entire three-dimensional droplet shape is investigated for different capillary numbers, allowing also reliable measurements of the time-resolved contact angle.

physics.flu-dyn↗

arXiv2023

Techno-economic assessment of long-distance supply chains of energy carriers: Comparing hydrogen and iron for carbon-free electricity generation

Effective usage of renewable energy requires ways of storage and delivery to balance energy demand and availability divergences. Carbon-free chemical energy carriers are proposed solutions, converting clean electricity into stable media for storage and long-distance energy trade. Hydrogen (H$_2$) is the subject of significant investment and research. Metal fuels, such as iron (Fe), are promising solutions for a clean energy supply, but establishing an interconnected ecosystem still requires considerable research and development. A model is proposed to assess the supply chain of hydrogen and iron as clean, carbon-free energy carriers and then examines case studies of possible trade routes between the potential energy exporters Morocco, Saudi Arabia, and Australia and importers Germany and Japan. The work comprehends the assessment of economic (levelized cost of electricity - LCOE), energetic (thermodynamic efficiency) and environmental (CO$_2$ emissions) aspects, quantified by the comprehensive model accounting for the most critical processes in the supply chain. Sensitivity and uncertainty analyses identify the main drivers for energy costs. Iron is shown to be lower-cost and more efficient to transport in longer routes and for long-term storage, but potentially more expensive and less efficient than H$_2$ to produce and convert. Uncertainties related to the supply chain specifications and the sensitivity to the used variables indicate that the path to viable energy carriers fundamentally depends on efficient synthesis, conversion, storage, and transport. A break-even analysis demonstrated that clean energy carriers could be competitive with conventional energy carriers at low renewable energy prices, while carbon taxes might be needed to level the playing field. Thereby, green iron is an important potential energy carrier for long-distance trade in a globalized clean energy market.

physics.soc-ph↗

arXiv2019

Numerical simulation of liquid film formation and its heat transfer through vapor bubble expansion in a microchannel

The evaporation of vapor bubbles inside a microchannel is important to realize a device with high cooling performance. The liquid film formed on the solid surface is essential for evaporative heat transfer from solid to fluid; its formation process and heat transfer characteristics need to be investigated. The expansion process of a single vapor bubble via evaporative heat transfer in microchannels was evaluated via a numerical simulation in this study. In the calculation model, the working fluid used was saturated FC-72 at 0.1013 MPa and the channel diameter was 200 $\mu$m. The superheat of the initial temperature field and wall were considered as parameters. To evaluate the heat transfer characteristics, the time variation of liquid film thickness was evaluated. The averaged liquid film thickness had a correlation with the capillary number. Additionally, the dominant heat transfer mode was estimated by decomposing the heat transfer rate into the heat-transfer rate through the liquid film, rear edge, and wake. When the superheat was low, the heat transfer mostly occurred via liquid film evaporation; the heat flux through the liquid film could be predicted using the liquid film thickness. On the other hand, in cases of higher superheat, owing to rapid expansion of the vapor bubble, no evaporative heat transfer occurred through the liquid film around the bubble head. It could be inferred from this study that the relationship between the thickness of the thermal boundary layer of the bubble and liquid film thickness is important for predicting the cooling effect of this phenomena. When the vapor bubble grows in the high superheat liquid, the rapid growth makes the liquid film thick, and the thick liquid film prevents the heat transfer between the liquid-vapor interface and heated wall.

physics.flu-dyn↗