arXiv subjects

Philippe Wenger

Publications and source records attributed to Philippe Wenger.

At least 55 records · Page 3Linked to original sources

arXiv2008

Singularity Analysis of Limited-dof Parallel Manipulators using Grassmann-Cayley Algebra

This paper characterizes geometrically the singularities of limited DOF parallel manipulators. The geometric conditions associated with the dependency of six Plücker vector of lines (finite and infinite) constituting the rows of the inverse Jacobian matrix are formulated using Grassmann-Cayley algebra. Manipulators under consideration do not need to have a passive spherical joint somewhere in each leg. This study is illustrated with three example robots

cs.RO↗

arXiv2008

SINGULAB - A Graphical user Interface for the Singularity Analysis of Parallel Robots based on Grassmann-Cayley Algebra

This paper presents SinguLab, a graphical user interface for the singularity analysis of parallel robots. The algorithm is based on Grassmann-Cayley algebra. The proposed tool is interactive and introduces the designer to the singularity analysis performed by this method, showing all the stages along the procedure and eventually showing the solution algebraically and graphically, allowing as well the singularity verification of different robot poses.

cs.RO↗

arXiv2008

Self-Motions of General 3-RPR Planar Parallel Robots

This paper studies the kinematic geometry of general 3-RPR planar parallel robots with actuated base joints. These robots, while largely overlooked, have simple direct kinematics and large singularity-free workspace. Furthermore, their kinematic geometry is the same as that of a newly developed parallel robot with SCARA-type motions. Starting from the direct and inverse kinematic model, the expressions for the singularity loci of 3-RPR planar parallel robots are determined. Then, the global behaviour at all singularities is geometrically described by studying the degeneracy of the direct kinematic model. Special cases of self-motions are then examined and the degree of freedom gained in such special configurations is kinematically interpreted. Finally, a practical example is discussed and experimental validations performed on an actual robot prototype are presented.

cs.RO↗

arXiv2008

Non-Singular Assembly-mode Changing Motions for 3-RPR Parallel Manipulators

When moving from one arbitrary location at another, a parallel manipulator may change its assembly-mode without crossing a singularity. Because the non-singular change of assembly-mode cannot be simply detected, the actual assembly-mode during motion is difficult to track. This paper proposes a global explanatory approach to help better understand non-singular assembly-mode changing motions for 3-RPR planar parallel manipulators. The approach consists in fixing one of the actuated joints and analyzing the configuration-space as a surface in a 3-dimensional space. Such a global description makes it possible to display all possible non-singular assembly-mode changing trajectories.

cs.RO↗

arXiv2008

Stiffness Analysis of 3-d.o.f. Overconstrained Translational Parallel Manipulators

The paper presents a new stiffness modelling method for overconstrained parallel manipulators, which is applied to 3-d.o.f. translational mechanisms. It is based on a multidimensional lumped-parameter model that replaces the link flexibility by localized 6-d.o.f. virtual springs. In contrast to other works, the method includes a FEA-based link stiffness evaluation and employs a new solution strategy of the kinetostatic equations, which allows computing the stiffness matrix for the overconstrained architectures and for the singular manipulator postures. The advantages of the developed technique are confirmed by application examples, which deal with comparative stiffness analysis of two translational parallel manipulators.

cs.RO↗

arXiv2007

Kinematic calibration of orthoglide-type mechanisms

The paper proposes a novel calibration approach for the Orthoglide-type mechanisms based on observations of the manipulator leg parallelism during mo-tions between the prespecified test postures. It employs a low-cost measuring system composed of standard comparator indicators attached to the universal magnetic stands. They are sequentially used for measuring the deviation of the relevant leg location while the manipulator moves the TCP along the Cartesian axes. Using the measured differences, the developed algorithm estimates the joint offsets that are treated as the most essential parameters to be adjusted. The sensitivity of the meas-urement methods and the calibration accuracy are also studied. Experimental re-sults are presented that demonstrate validity of the proposed calibration technique

cs.RO↗

arXiv2007

Singular Curves in the Joint Space and Cusp Points of 3-RPR parallel manipulators

This paper investigates the singular curves in the joint space of a family of planar parallel manipulators. It focuses on special points, referred to as cusp points, which may appear on these curves. Cusp points play an important role in the kinematic behavior of parallel manipulators since they make possible a nonsingular change of assembly mode. The purpose of this study is twofold. First, it exposes a method to compute joint space singular curves of 3-RPR planar parallel manipulators. Second, it presents an algorithm for detecting and computing all cusp points in the joint space of these same manipulators.

cs.RO↗

arXiv2007

A DH-parameter based condition for 3R orthogonal manipulators to have 4 distinct inverse kinematic solutions

Positioning 3R manipulators may have two or four inverse kinematic solutions (IKS). This paper derives a necessary and sufficient condition for 3R positioning manipulators with orthogonal joint axes to have four distinct IKS. We show that the transition between manipulators with 2 and 4 IKS is defined by the set of manipulators with a quadruple root of their inverse kinematics. The resulting condition is explicit and states that the last link length of the manipulator must be greater than a quantity that depends on three of its remaining DH-parameters. This result is of interest for the design of new manipulators.

cs.RO↗

arXiv2007

The Isoconditioning Loci of Planar Three-DOF Parallel Manipulators

The subject of this paper is a special class of three-degree-of-freedom parallel manipulators. The singular configurations of the two Jacobian matrices are first studied. The isotropic configurations are then found based on the characteristic length of this manipulator. The isoconditioning loci for the Jacobian matrices are plotted to define a global performance index allowing the comparison of the different working modes. The index thus resulting is compared with the Cartesian workspace surface and the average of the condition number.

cs.RO↗

arXiv2007

Kinematic analysis of the 3-RPR parallel manipulator

The aim of this paper is the kinematic study of a 3-RPR planar parallel manipulator where the three fixed revolute joints are actuated. The direct and inverse kinematic problem as well as the singular configuration is characterized. On parallel singular configurations, the motion produce by the mobile platform can be compared to the Reuleaux straight-line mechanism.

cs.RO↗

arXiv2007

Working and Assembly Modes of the Agile Eye

This paper deals with the in-depth kinematic analysis of a special spherical parallel wrist, called the Agile Eye. The Agile Eye is a three-legged spherical parallel robot with revolute joints in which all pairs of adjacent joint axes are orthogonal. Its most peculiar feature, demonstrated in this paper for the first time, is that its (orientation) workspace is unlimited and flawed only by six singularity curves (rather than surfaces). Furthermore, these curves correspond to self-motions of the mobile platform. This paper also demonstrates that, unlike for any other such complex spatial robots, the four solutions to the direct kinematics of the Agile Eye (assembly modes) have a simple geometric relationship with the eight solutions to the inverse kinematics (working modes).

cs.RO↗

arXiv2007

Parametric Stiffness Analysis of the Orthoglide

This paper presents a parametric stiffness analysis of the Orthoglide, a 3-DOF translational Parallel Kinematic Machine. First, a compliant modeling of the Orthoglide is conducted based on an existing method. Then stiffness matrix is symbolically computed. This allows one to easily study the influence of the geometric design parameters on the matrix elements. Critical links are displayed. Cutting forces are then modeled so that static displacements of the Orthoglide tool during slot milling are symbolically computed. Influence of the geometric design parameters on the static displacements is checked as well. Other machining operations can be modeled. This parametric stiffness analysis can be applied to any parallel manipulator for which stiffness is a critical issue.

cs.RO↗

arXiv2007

Design Strategies for the Geometric Synthesis of Orthoglide-type Mechanisms

The paper addresses the geometric synthesis of Orthoglide-type mechanism, a family of 3-DOF parallel manipulators for rapid machining applications, which combine advantages of both serial mechanisms and parallel kinematic architectures. These manipulators possess quasi-isotropic kinematic performances and are made up of three actuated fixed prismatic joints, which are mutually orthogonal and connected to a mobile platform via three parallelogram chains. The platform moves in the Cartesian space with fixed orientation, similar to conventional XYZ-machine. Three strategies have been proposed to define the Orthoglide geometric parameters (manipulator link lengths and actuated joint limits) as functions of a cubic workspace size and dextrous properties expressed by bounds on the velocity transmission factors, manipulability or the Jacobian condition number. Low inertia and intrinsic stiffness have been set as additional design goals expressed by the minimal link length requirement. For each design strategy, analytical expressions for computing the Orthoglide parameters are proposed. It is showed that the proposed strategies yield Pareto-optimal solutions, which differ by the kinematic performances outside the prescribed Cartesian cube (but within the workspace bounded by the actuated joint limits). The proposed technique is illustrated with numerical examples for the Orthoglide prototype design.

cs.RO↗

arXiv2007

An Exhaustive Study of the Workspaces Tolopogies of all 3R Orthogonal Manipulators with Geometric Simplifications

This paper proposes a classification of three-revolute orthogonal manipulators that have at least one of their DH parameters equal to zero. This classification is based on the topology of their workspace. The workspace is characterized in a half-cross section by the singular curves. The workspace topology is defined by the number of cusps and nodes that appear on these singular curves. The manipulators are classified into different types with similar kinematic properties. Each type is evaluated according to interesting kinematic properties such as, whether the workspace is fully reachable with four inverse kinematic solutions or not, the existence of voids, and the feasibility of continuous trajectories in the workspace. It is found that several orthogonal manipulators have a "well-connected" workspace, that is, their workspace is fully accessible with four inverse kinematic solutions and any continuous trajectory is feasible. This result is of interest for the design of alternative manipulator geometries.

cs.RO↗

arXiv2007

Parametric stiffness analysis of the Orthoglide

This paper presents a parametric stiffness analysis of the Orthoglide. A compliant modeling and a symbolic expression of the stiffness matrix are conducted. This allows a simple systematic analysis of the influence of the geometric design parameters and to quickly identify the critical link parameters. Our symbolic model is used to display the stiffest areas of the workspace for a specific machining task. Our approach can be applied to any parallel manipulator for which stiffness is a critical issue.

cs.RO↗

arXiv2007

Kinematics and Workspace Analysis of a Three-Axis Parallel Manipulator: the Orthoglide

The paper addresses kinematic and geometrical aspects of the Orthoglide, a three-DOF parallel mechanism. This machine consists of three fixed linear joints, which are mounted orthogonally, three identical legs and a mobile platform, which moves in the Cartesian x-y-z space with fixed orientation. New solutions to solve inverse/direct kinematics are proposed and we perform a detailed workspace and singularity analysis, taking into account specific joint limit constraints.

cs.RO↗

arXiv2007

Architecture Optimization of a 3-DOF Translational Parallel Mechanism for Machining Applications, the Orthoglide

This paper addresses the architecture optimization of a 3-DOF translational parallel mechanism designed for machining applications. The design optimization is conducted on the basis of a prescribed Cartesian workspace with prescribed kinetostatic performances. The resulting machine, the Orthoglide, features three fixed parallel linear joints which are mounted orthogonally and a mobile platform which moves in the Cartesian x-y-z space with fixed orientation. The interesting features of the Orthoglide are a regular Cartesian workspace shape, uniform performances in all directions and good compactness. A small-scale prototype of the Orthoglide under development is presented at the end of this paper.

cs.RO↗

arXiv2007

An Interval Analysis Based Study for the Design and the Comparison of 3-DOF Parallel Kinematic Machines

This paper addresses an interval analysis based study that is applied to the design and the comparison of 3-DOF parallel kinematic machines. Two design criteria are used, (i) a regular workspace shape and, (ii) a kinetostatic performance index that needs to be as homogeneous as possible throughout the workspace. The interval analysis based method takes these two criteria into account: on the basis of prescribed kinetostatic performances, the workspace is analysed to find out the largest regular dextrous workspace enclosed in the Cartesian workspace. An algorithm describing this method is introduced. Two 3-DOF translational parallel mechanisms designed for machining applications are compared using this method. The first machine features three fixed linear joints which are mounted orthogonally and the second one features three linear joints which are mounted in parallel. In both cases, the mobile platform moves in the Cartesian x-y-z space with fixed orientation.

cs.RO↗