arXiv subjects

Pierre Martin-Cocher

Publications and source records attributed to Pierre Martin-Cocher.

At least 19 recordsLinked to original sources

arXiv2026

First Very Long Baseline Interferometry Fringe Detection at 690GHz

We report the first very long baseline interferometry (VLBI) experiment conducted in the 690 GHz atmospheric window. On 2024 November 21, observations with the Atacama Large Millimeter/submillimeter Array, the Atacama Pathfinder EXperiment (APEX), and the James Clerk Maxwell Telescope (JCMT) were carried out using ALMA's newly developed Band 9 phasing capability. Fringes were detected on the ALMA-APEX baseline during a scan of the quasar J0423-0120, with a signal-to-noise ratio of ~12 and useful fringe recovery over solution intervals of order tens of seconds, representing the highest-frequency ground-based VLBI fringe detection reported to date. No fringes were found on the ALMA-JCMT baseline, despite excellent weather conditions, consistent with sensitivity predictions and supporting baseline performance models. The ALMA Phasing System maintained stable phasing at Band 9 for ~1-2 minutes before gradually degrading, indicating limitations under these observing conditions. Our analysis shows that, under excellent weather conditions, 690 GHz VLBI can still support fringe recovery over short solution intervals, despite rapid atmospheric phase fluctuations at these frequencies. This work validated key elements of near-terahertz VLBI operation and establishes a technical foundation for routine observations in the 690 GHz atmospheric window.

astro-ph.IM↗

arXiv2023

The Greenland Telescope: Construction, Commissioning, and Operations in Pituffik

In 2018, the Greenland Telescope (GLT) started scientific observation in Greenland. Since then, we have completed several significant improvements and added new capabilities to the telescope system. This paper presents a full review of the GLT system, a summary of our observation activities since 2018, the lessons learned from the operations in the Arctic regions, and the prospect of the telescope.

astro-ph.IM↗

arXiv2023

A ring-like accretion structure in M87 connecting its black hole and jet

The nearby radio galaxy M87 is a prime target for studying black hole accretion and jet formation^{1,2}. Event Horizon Telescope observations of M87 in 2017, at a wavelength of 1.3 mm, revealed a ring-like structure, which was interpreted as gravitationally lensed emission around a central black hole^3. Here we report images of M87 obtained in 2018, at a wavelength of 3.5 mm, showing that the compact radio core is spatially resolved. High-resolution imaging shows a ring-like structure of 8.4_{-1.1}^{+0.5} Schwarzschild radii in diameter, approximately 50% larger than that seen at 1.3 mm. The outer edge at 3.5 mm is also larger than that at 1.3 mm. This larger and thicker ring indicates a substantial contribution from the accretion flow with absorption effects in addition to the gravitationally lensed ring-like emission. The images show that the edge-brightened jet connects to the accretion flow of the black hole. Close to the black hole, the emission profile of the jet-launching region is wider than the expected profile of a black-hole-driven jet, suggesting the possible presence of a wind associated with the accretion flow.

astro-ph.HE↗

arXiv2018

Electronics Instrumentation for the Greenland Telescope

The Greenland Telescope project has recently participated in an experiment to image the supermassive black hole shadow at the center of M87 using Very Long Baseline Interferometry technique in April of 2018. The antenna consists of the 12-m ALMA North American prototype antenna that was modified to support two auxiliary side containers and to withstand an extremely cold environment. The telescope is currently at Thule Air Base in Greenland with the long-term goal to move the telescope over the Greenland ice sheet to Summit Station. The GLT currently has a single cryostat which houses three dual polarization receivers that cover 84-96 GHz, 213-243 GHz and 271-377 GHz bands. A hydrogen maser frequency source in conjunction with high frequency synthesizers are used to generate the local oscillator references for the receivers. The intermediate frequency outputs of each receiver cover 4-8 GHz and are heterodyned to baseband for digitization within a set of ROACH-2 units then formatted for recording onto Mark-6 data recorders. A separate set of ROACH-2 units operating in parallel provides the function of auto-correlation for real-time spectral analysis. Due to the stringent instrumental stability requirements for interferometry a diagnostic test system was incorporated into the design. Tying all of the above equipment together is the fiber optic system designed to operate in a low temperature environment and scalable to accommodate a larger distance between the control module and telescope for Summit Station. A report on the progress of the above electronics instrumentation system will be provided.

astro-ph.IM↗

arXiv2016

The Greenland Telescope: Antenna Retrofit Status and Future Plans

Since the ALMA North America Prototype Antenna was awarded to the Smithsonian Astrophysical Observatory (SAO), SAO and the Academia Sinica Institute of Astronomy & Astrophysics (ASIAA) are working jointly to relocate the antenna to Greenland. This paper shows the status of the antenna retrofit and the work carried out after the recommissioning and subsequent disassembly of the antenna at the VLA has taken place. The next coming months will see the start of the antenna reassembly at Thule Air Base. These activities are expected to last until the fall of 2017 when commissioning should take place. In parallel, design, fabrication and testing of the last components are taking place in Taiwan.

astro-ph.IM↗

arXiv2016

AMiBA: Cluster Sunyaev-Zel'dovich Effect Observations with the Expanded 13-Element Array

The Yuan-Tseh Lee Array for Microwave Background Anisotropy (AMiBA) is a co-planar interferometer array operating at a wavelength of 3mm to measure the Sunyaev-Zeldovich effect (SZE) of galaxy clusters. In the first phase of operation -- with a compact 7-element array with 0.6m antennas (AMiBA-7) -- we observed six clusters at angular scales from 5\arcmin to 23\arcmin. Here, we describe the expansion of AMiBA to a 13-element array with 1.2m antennas (AMiBA-13), its subsequent commissioning, and our cluster SZE observing program. The most important changes compared to AMiBA-7 are (1) array re-configuration with baselines ranging from 1.4m to 4.8m covering angular scales from 2\arcmin to 11.5\arcmin, (2) thirteen new lightweight carbon-fiber-reinforced plastic (CFRP) 1.2m reflectors, and (3) additional correlators and six new receivers. From the AMiBA-13 SZE observing program, we present here maps of a subset of twelve clusters. In highlights, we combine AMiBA-7 and AMiBA-13 observations of Abell 1689 and perform a joint fitting assuming a generalized NFW pressure profile. Our cylindrically integrated Compton-y values for this cluster are consistent with the BIMA/OVRA, SZA, and Planck results. We report the first targeted SZE detection towards the optically selected galaxy cluster RCS J1447+0828, and we demonstrate the ability of AMiBA SZE data to serve as a proxy for the total cluster mass. Finally, we show that our AMiBA-SZE derived cluster masses are consistent with recent lensing mass measurements in the literature.

astro-ph.CO↗

arXiv2015

First-generation Science Cases for Ground-based Terahertz Telescopes

Ground-based observations at terahertz (THz) frequencies are a newly explorable area of astronomy for the next ten years. We discuss science cases for a first-generation 10-m class THz telescope, focusing on the Greenland Telescope as an example of such a facility. We propose science cases and provide quantitative estimates for each case. The largest advantage of ground-based THz telescopes is their higher angular resolution (~ 4 arcsec for a 10-m dish), as compared to space or airborne THz telescopes. Thus, high-resolution mapping is an important scientific argument. In particular, we can isolate zones of interest for Galactic and extragalactic star-forming regions. The THz windows are suitable for observations of high-excitation CO lines and [N II] 205 um lines, which are scientifically relevant tracers of star formation and stellar feedback. Those lines are the brightest lines in the THz windows, so that they are suitable for the initiation of ground-based THz observations. THz polarization of star-forming regions can also be explored since it traces the dust population contributing to the THz spectral peak. For survey-type observations, we focus on ``sub-THz'' extragalactic surveys, whose uniqueness is to detect galaxies at redshifts z ~ 1--2, where the dust emission per comoving volume is the largest in the history of the Universe. Finally we explore possibilities of flexible time scheduling, which enables us to monitor active galactic nuclei, and to target gamma-ray burst afterglows. For these objects, THz and submillimeter wavelength ranges have not yet been explored.

astro-ph.GA↗

arXiv2014

The Greenland Telescope (GLT): Antenna status and future plans

The ALMA North America Prototype Antenna was awarded to the Smithsonian Astrophysical Observatory (SAO) in 2011. SAO and the Academia Sinica Institute of Astronomy & Astrophysics (ASIAA), SAO's main partner for this project, are working jointly to relocate the antenna to Greenland to carry out millimeter and submillimeter VLBI observations. This paper presents the work carried out on upgrading the antenna to enable operation in the Arctic climate by the GLT Team to make this challenging project possible, with an emphasis on the unexpected telescope components that had to be either redesigned or changed. Five-years of inactivity, with the antenna laying idle in the desert of New Mexico, coupled with the extreme weather conditions of the selected site in Greenland have it necessary to significantly refurbish the antenna. We found that many components did need to be replaced, such as the antenna support cone, the azimuth bearing, the carbon fiber quadrupod, the hexapod, the HVAC, the tiltmeters, the antenna electronic enclosures housing servo and other drive components, and the cables. We selected Vertex, the original antenna manufacturer, for the main design work, which is in progress. The next coming months will see the major antenna components and subsystems shipped to a site of the US East Coast for test-fitting the major antenna components, which have been retrofitted. The following step will be to ship the components to Greenland to carry out VLBI and single dish observations. Antenna reassembly at Summit Station should take place during the summer of 2018.

astro-ph.IM↗

arXiv2013

ALMA Nutator Design and Preliminary Performance

We report the past two years of collaboration between the different actors on the ALMA nutator. Building on previous developments, the nutator has seen changes in much of the design. A high-modulus carbon fiber structure has been added on the back of the mirror in order to transfer the voice coils forces with less deformation, thus reducing delay problems due to flexing. The controller is now an off-the-shelf National Instrument NI-cRIO, and the amplifier a class D servo drive from Advanced Motion Controls, with high peak power able to drive the coils at 300 Volts DC. The stow mechanism has been totally redesigned to improve on the repeatability and precision of the stow position, which is also the reference for the 26 bits Heidenhain encoders. This also improves on the accuracy of the stow position with wind loading. Finally, the software, written largely with National Instrument's LabView, has been developed. We will discuss these changes and the preliminary performances achieved to date. Keywords: ALMA, nutator, class D, high-modulus carbon fiber.

astro-ph.IM↗

arXiv2013

Platform Deformation Phase Correction for the AMiBA-13 Co-planar Interferometer

We present a new way to solve the platform deformation problem of co-planar interferometers. The platform of a co-planar interferometer can be deformed due to driving forces and gravity. A deformed platform will induce extra components into the geometric delay of each baseline, and change the phases of observed visibilities. The reconstructed images will also be diluted due to the errors of the phases. The platform deformations of The Yuan-Tseh Lee Array for Microwave Background Anisotropy (AMiBA) were modelled based on photogrammetry data with about 20 mount pointing positions. We then used the differential optical pointing error between two optical telescopes to fit the model parameters in the entire horizontal coordinate space. With the platform deformation model, we can predict the errors of the geometric phase delays due to platform deformation with given azimuth and elevation of the targets and calibrators. After correcting the phases of the radio point sources in the AMiBA interferometric data, we recover 50% - 70% flux loss due to phase errors. This allows us to restore more than 90% of a source flux. The method outlined in this work is not only applicable to the correction of deformation for other co-planar telescopes but also to single dish telescopes with deformation problems. This work also forms the basis of the upcoming science results of AMiBA-13.

astro-ph.IM↗

arXiv2010

Contamination of the Central Sunyaev--Zel'dovich Decrements in AMiBA Galaxy Cluster Observations

We investigate the contamination of the Sunyaev--Zel'dovich (SZ) effect for six galaxy clusters, A1689, A1995, A2142, A2163, A2261, and A2390, observed by the Y. T. Lee Array for Microwave Background Anisotropy during 2007. With the range of baselines used, we find that the largest effect (of order 13%-50% of the central SZ flux density) comes from primary anisotropies in the cosmic microwave background and exceeds the thermal noise in all six cases. Contamination from discrete radio sources is estimated to be at a level of (3%-60%) of the central SZ flux density. We use the statistics of these contaminating sources to estimate and correct the errors in the measured SZ effects of these clusters.

astro-ph.CO↗

arXiv2010

AMiBA Wideband Analog Correlator

A wideband analog correlator has been constructed for the Yuan-Tseh Lee Array for Microwave Background Anisotropy. Lag correlators using analog multipliers provide large bandwidth and moderate frequency resolution. Broadband IF distribution, backend signal processing and control are described. Operating conditions for optimum sensitivity and linearity are discussed. From observations, a large effective bandwidth of around 10 GHz has been shown to provide sufficient sensitivity for detecting cosmic microwave background variations.

astro-ph.CO↗

arXiv2010

AMiBA: Sunyaev-Zel'dovich effect derived properties and scaling relations of massive galaxy clusters

The Sunyaev-Zel'dovich Effect (SZE) has been observed toward six massive galaxy clusters, at redshifts 0.091 \leq z \leq 0.322 in the 86-102 GHz band with the Y. T. Lee Array for Microwave Background Anisotropy (AMiBA). We modify an iterative method, based on the isothermal β-models, to derive the electron temperature T_e, total mass M_t, gas mass M_g, and integrated Compton Y within r_2500, from the AMiBA SZE data. Non-isothermal universal temperature profile (UTP) βmodels are also considered in this paper. These results are in good agreement with those deduced from other observations. We also investigate the embedded scaling relations, due to the assumptions that have been made in the method we adopted, between these purely SZE-deduced T_e, M_t, M_g and Y. Our results suggest that cluster properties may be measurable with SZE observations alone. However, the assumptions built into the pure-SZE method bias the results of scaling relation estimations and need further study.

astro-ph.CO↗

arXiv2009

AMiBA: scaling relations between the integrated Compton-y and X-ray derived temperature, mass, and luminosity

We investigate the scaling relations between the X-ray and the thermal Sunyaev-Zel'dovich Effect (SZE) properties of clusters of galaxies, using data taken during 2007 by the Y.T. Lee Array for Microwave Background Anisotropy (AMiBA) at 94 GHz for the six clusters A1689, A1995, A2142, A2163, A2261, and A2390. The scaling relations relate the integrated Compton-y parameter Y_{2500} to the X-ray derived gas temperature T_{e}, total mass M_{2500}, and bolometric luminosity L_X within r_{2500}. Our results for the power-law index and normalization are both consistent with the self-similar model and other studies in the literature except for the Y_{2500}-L_X relation, for which a physical explanation is given though further investigation may be still needed. Our results not only provide confidence for the AMiBA project but also support our understanding of galaxy clusters.

astro-ph.CO↗

arXiv2009

Platform Deformation Refined Pointing and Phase Correction for the AMiBA Hexapod Telescope

The Array for Microwave Background Anisotropy (AMiBA) is a radio interferometer for research in cosmology, currently operating 7 0.6m diameter antennas co-mounted on a 6m diameter platform driven by a hexapod mount. AMiBA is currently the largest hexapod telescope. We briefly summarize the hexapod operation with the current pointing error model. We then focus on the upcoming 13-element expansion with its potential difficulties and solutions. Photogrammetry measurements of the platform reveal deformations at a level which can affect the optical pointing and the receiver radio phase. In order to prepare for the 13-element upgrade, two optical telescopes are installed on the platform to correlate optical pointing tests. Being mounted on different locations, the residuals of the two sets of pointing errors show a characteristic phase and amplitude difference as a function of the platform deformation pattern. These results depend on the telescope's azimuth, elevation and polarization position. An analytical model for the deformation is derived in order to separate the local deformation induced error from the real hexapod pointing error. Similarly, we demonstrate that the deformation induced radio phase error can be reliably modeled and calibrated, which allows us to recover the ideal synthesized beam in amplitude and shape of up to 90% or more. The resulting array efficiency and its limits are discussed based on the derived errors.

astro-ph.IM↗

arXiv2009

AMiBA: Broadband Heterodyne CMB Interferometry

The Y. T. Lee Array for Microwave Background (AMiBA) has reported the first science results on the detection of galaxy clusters via the Sunyaev Zel'dovich effect. The science objectives required small reflectors in order to sample large scale structures (20') while interferometry provided modest resolutions (2'). With these constraints, we designed for the best sensitivity by utilizing the maximum possible continuum bandwidth matched to the atmospheric window at 86-102GHz, with dual polarizations. A novel wide-band analog correlator was designed that is easily expandable for more interferometer elements. MMIC technology was used throughout as much as possible in order to miniaturize the components and to enhance mass production. These designs will find application in other upcoming astronomy projects. AMiBA is now in operations since 2006, and we are in the process to expand the array from 7 to 13 elements.

astro-ph.CO↗

arXiv2009

AMiBA: System Performance

The Y.T. Lee Array for Microwave Background Anisotropy (AMiBA) started scientific operation in early 2007. This work describes the optimization of the system performance for the measurements of the Sunyaev-Zel'dovich effect for six massive galaxy clusters at redshifts $0.09 - 0.32$. We achieved a point source sensitivity of $63\pm 7$ mJy with the seven 0.6m dishes in 1 hour of on-source integration in 2-patch differencing observations. We measured and compensated for the delays between the antennas of our platform-mounted interferometer. Beam switching was used to cancel instrumental instabilities and ground pick up. Total power and phase stability were good on time scales of hours, and the system was shown to integrate down on equivalent timescales of 300 hours per baseline/correlation, or about 10 hours for the entire array. While the broadband correlator leads to good sensitivity, the small number of lags in the correlator resulted in poorly measured bandpass response. We corrected for this by using external calibrators (Jupiter and Saturn). Using Jupiter as the flux standard, we measured the disk brightness temperature of Saturn to be $149^{+5}_{-12}$ K.

astro-ph.IM↗

arXiv2009

The AMiBA Hexapod Telescope Mount

AMiBA is the largest hexapod astronomical telescope in current operation. We present a description of this novel hexapod mount with its main mechanical components -- the support cone, universal joints, jack screws, and platform -- and outline the control system with the pointing model and the operating modes that are supported. The AMiBA hexapod mount performance is verified based on optical pointing tests and platform photogrammetry measurements. The photogrammetry results show that the deformations in the inner part of the platform are less than 120 micron rms. This is negligible for optical pointing corrections, radio alignment and radio phase errors for the currently operational 7-element compact configuration. The optical pointing error in azimuth and elevation is successively reduced by a series of corrections to about 0.4 arcmin rms which meets our goal for the 7-element target specifications.

astro-ph.CO↗