arXiv subjects

Q. Y. Tang

Publications and source records attributed to Q. Y. Tang.

6 recordsLinked to original sources

arXiv2020

Reducing the susceptibility of lumped-element KIDs to two-level system effects

Arrays of lumped-element kinetic inductance detectors (LEKIDs) optically coupled through an antenna-coupled transmission line are a promising candidate for future cosmic microwave background (CMB) experiments. However, the dielectric materials used for the microstrip architecture are known to degrade the performance of superconducting resonators. In this paper, we investigate the feasibility of microstrip coupling to a LEKID, focusing on a systematic study of the effect of depositing amorphous silicon-nitride on a LEKID. The discrete and spatially-separated inductive and capacitive regions of the LEKID allow us to vary the degree of dielectric coverage and determine the limitations of the microstrip coupling architecture. We show that by careful removal of dielectric from regions of high electric field in the capacitor, there is minimal degradation in dielectric loss tangent of a partially covered lumped-element resonator. We present the effects on the resonant frequency and noise power spectral density and, using the dark responsivity, provide an estimate for the resulting detector sensitivity.

astro-ph.IM↗

arXiv2020

LEKID sensitivity for space applications between 80 and 600 GHz

We report the design, fabrication and testing of Lumped Element Kinetic Inductance Detectors (LEKID) showing performance in line with the requirements of the next generation space telescopes operating in the spectral range from 80 to 600 GHz. This range is of particular interest for Cosmic Microwave Background (CMB) studies. For this purpose we have designed and fabricated 100-pixel arrays covering five distinct bands. These wafers have been measured via multiplexing, where a full array is read out using a single pair of lines. We adopted a custom cold black-body installed in front of the detectors and regulated at temperatures between 1 K and 20 K. We will describe in the present paper the main design considerations, the fabrication processes, the testing and the data analysis.

astro-ph.IM↗

arXiv2019

Design and Bolometer Characterization of the SPT-3G First-year Focal Plane

During the austral summer of 2016-17, the third-generation camera, SPT-3G, was installed on the South Pole Telescope, increasing the detector count in the focal plane by an order of magnitude relative to the previous generation. Designed to map the polarization of the cosmic microwave background, SPT-3G contains ten 6-in-hexagonal modules of detectors, each with 269 trichroic and dual-polarization pixels, read out using 68x frequency-domain multiplexing. Here we discuss design, assembly, and layout of the modules, as well as early performance characterization of the first-year array, including yield and detector properties.

astro-ph.IM↗

arXiv2018

Design and performance of the antenna coupled lumped-element kinetic inductance detector

Focal plane arrays consisting of low-noise, polarisation-sensitive detectors have made possible the pioneering advances in the study of the cosmic microwave background (CMB). To make further progress, the next generation of CMB experiments (e.g. CMB-S4) will require a substantial increase in the number of detectors compared to the current stage 3 instruments. Arrays of kinetic inductance detectors (KIDs) provide a possible path to realising such large format arrays owing to their intrinsic multiplexing advantage and relative cryogenic simplicity. In this proceedings, we report on the design of a novel variant of the traditional KID design; the antenna-coupled lumped-element KID. A polarisation sensitive twin-slot antenna placed behind an optimised hemispherical lens couples power onto a thin-film superconducting microstrip line. The power is then guided into the inductive section of an aluminium KID where it is absorbed and modifies both the resonant frequency and quality factor of the KID. We present the various aspects of the design and preliminary results from the first set of seven-element prototype arrays and compare to the expected modelled performance.

astro-ph.IM↗

arXiv2017

Fabrication of antenna-coupled KID array for Cosmic Microwave Background detection

Kinetic Inductance Detectors (KIDs) have become an attractive alternative to traditional bolometers in the sub-mm and mm observing community due to their innate frequency multiplexing capabilities and simple lithographic processes. These advantages make KIDs a viable option for the $O(500,000)$ detectors needed for the upcoming Cosmic Microwave Background - Stage 4 (CMB-S4) experiment. We have fabricated antenna-coupled MKID array in the 150GHz band optimized for CMB detection. Our design uses a twin slot antenna coupled to inverted microstrip made from a superconducting Nb/Al bilayer and SiN$_x$, which is then coupled to an Al KID grown on high resistivity Si. We present the fabrication process and measurements of SiN$_x$ microstrip resonators.

astro-ph.IM↗

arXiv2016

ICE: a scalable, low-cost FPGA-based telescope signal processing and networking system

We present an overview of the 'ICE' hardware and software framework that implements large arrays of interconnected FPGA-based data acquisition, signal processing and networking nodes economically. The system was conceived for application to radio, millimeter and sub-millimeter telescope readout systems that have requirements beyond typical off-the-shelf processing systems, such as careful control of interference signals produced by the digital electronics, and clocking of all elements in the system from a single precise observatory-derived oscillator. A new generation of telescopes operating at these frequency bands and designed with a vastly increased emphasis on digital signal processing to support their detector multiplexing technology or high-bandwidth correlators---data rates exceeding a terabyte per second---are becoming common. The ICE system is built around a custom FPGA motherboard that makes use of an Xilinx Kintex-7 FPGA and ARM-based co-processor. The system is specialized for specific applications through software, firmware, and custom mezzanine daughter boards that interface to the FPGA through the industry-standard FMC specifications. For high density applications, the motherboards are packaged in 16-slot crates with ICE backplanes that implement a low-cost passive full-mesh network between the motherboards in a crate, allow high bandwidth interconnection between crates, and enable data offload to a computer cluster. A Python-based control software library automatically detects and operates the hardware in the array. Examples of specific telescope applications of the ICE framework are presented, namely the frequency-multiplexed bolometer readout systems used for the SPT and Simons Array and the digitizer, F-engine, and networking engine for the CHIME and HIRAX radio interferometers.

astro-ph.IM↗