Searcharxiv⌕ Search

arXiv subjects

Qingqing Wu

Publications and source records attributed to Qingqing Wu.

At least 235 records · Page 13Linked to original sources
arXiv2023

Hybrid Active-Passive IRS Assisted Energy-Efficient Wireless Communication

Deploying active reflecting elements at the intelligent reflecting surface (IRS) increases signal amplification capability but incurs higher power consumption. Therefore, it remains a challenging and open problem to determine the optimal number of active/passive elements for maximizing energy efficiency (EE). To answer this question, we consider a hybrid active-passive IRS (H-IRS) assisted wireless communication system, where the H-IRS consists of both active and passive reflecting elements.Specifically, we study the optimization of the number of active/passive elements at the H-IRS to maximize EE. To this end, we first derive the closed-form expression for a near-optimal solution under the line-of-sight (LoS) channel case and obtain its optimal solution under the Rayleigh fading channel case. Then, an efficient algorithm is employed to obtain a high-quality sub-optimal solution for the EE maximization under the general Rician channel case. Simulation results demonstrate the effectiveness of the H-IRS for maximizing EE under different Rician factors and IRS locations.

cs.IT↗
arXiv2023

Delay-aware Multiple Access Design for Intelligent Reflecting Surface Aided Uplink Transmission

In this paper, we develop a hybrid multiple access (MA) protocol for an intelligent reflecting surface (IRS) aided uplink transmission network by incorporating the IRS-aided time-division MA (I-TDMA) protocol and the IRS-aided non-orthogonal MA (I-NOMA) protocol as special cases. Two typical communication scenarios, namely the transmit power limited case and the transmit energy limited case are considered, where the device's rearranged order, time and power allocation, as well as dynamic IRS beamforming patterns over time are jointly optimized to minimize the sum transmission delay. To shed light on the superiority of the proposed IRS-aided hybrid MA (I-HMA) protocol over conventional protocols, the conditions under which I-HMA outperforms I-TDMA and I-NOMA are revealed by characterizing their corresponding optimal solution. Then, a computationally efficient algorithm is proposed to obtain the high-quality solution to the corresponding optimization problems. Simulation results validate our theoretical findings, demonstrate the superiority of the proposed design, and draw some useful insights. Specifically, it is found that the proposed protocol can significantly reduce the sum transmission delay by combining the additional gain of dynamic IRS beamforming with the high spectral efficiency of NOMA, which thus reveals that integrating IRS into the proposed HMA protocol is an effective solution for delay-aware optimization. Furthermore, it reveals that the proposed design reduces the time consumption not only from the system-centric view, but also from the device-centric view.

cs.IT↗
arXiv2023

Intelligent Reflecting Surface Empowered Self-Interference Cancellation in Full-Duplex Systems

Compared with traditional half-duplex wireless systems, the application of emerging full-duplex (FD) technology can potentially double the system capacity theoretically. However, conventional techniques for suppressing self-interference (SI) adopted in FD systems require exceedingly high power consumption and expensive hardware. In this paper, we consider employing an intelligent reflecting surface (IRS) in the proximity of an FD base station (BS) to mitigate SI for simultaneously receiving data from uplink users and transmitting information to downlink users. The objective considered is to maximize the weighted sum-rate of the system by jointly optimizing the IRS phase shifts, the BS transmit beamformers, and the transmit power of the uplink users. To visualize the role of the IRS in SI cancellation by isolating other interference, we first study a simple scenario with one downlink user and one uplink user. To address the formulated non-convex problem, a low-complexity algorithm based on successive convex approximation is proposed. For the more general case considering multiple downlink and uplink users, an efficient alternating optimization algorithm based on element-wise optimization is proposed. Numerical results demonstrate that the FD system with the proposed schemes can achieve a larger gain over the half-duplex system, and the IRS is able to achieve a balance between suppressing SI and providing beamforming gain.

cs.IT↗
arXiv2023

Performance-Oriented Design for Intelligent Reflecting Surface Assisted Federated Learning

To efficiently exploit the massive amounts of raw data that are increasingly being generated in mobile edge networks, federated learning (FL) has emerged as a promising distributed learning technique. By collaboratively training a shared learning model on edge devices, raw data transmission and storage are replaced by the exchange of the local computed parameters/gradients in FL, which thus helps address latency and privacy issues. However, the number of resource blocks when using traditional orthogonal transmission strategies for FL linearly scales with the number of participating devices, which conflicts with the scarcity of communication resources. To tackle this issue, over-the-air computation (AirComp) has emerged recently which leverages the inherent superposition property of wireless channels to perform one-shot model aggregation. However, the aggregation accuracy in AirComp suffers from the unfavorable wireless propagation environment. In this paper, we consider the use of intelligent reflecting surfaces (IRSs) to mitigate this problem and improve FL performance with AirComp. Specifically, a performance-oriented design scheme that directly minimizes the optimality gap of the loss function is proposed to accelerate the convergence of AirComp-based FL. We first analyze the convergence behavior of the FL procedure with the absence of channel fading and noise. Based on the obtained optimality gap which characterizes the impact of channel fading and noise in different communication rounds on the ultimate performance of FL, we propose both online and offline approaches to tackle the resulting design problem. Simulation results demonstrate that such a performance-oriented design strategy can achieve higher test accuracy than the conventional isolated mean square error (MSE) minimization approach in FL.

cs.IT↗
arXiv2023

Intelligent Surface Empowered Sensing and Communication: A Novel Mutual Assistance Design

Integrated sensing and communication (ISAC) is a promising paradigm to provide both sensing and communication (S&C) services in vehicular networks. However, the power of echo signals reflected from vehicles may be too weak to be used for future precise positioning, due to the practically small radar cross section of vehicles with random reflection/scattering coefficient. To tackle this issue, we propose a novel mutual assistance scheme for intelligent surface-mounted vehicles, where S&C are innovatively designed to assist each other for achieving an efficient win-win integration, i.e., sensing-assisted phase shift design and communication-assisted high-precision sensing. Specifically, we first derive closed-form expressions of the echo power and achievable rate under uncertain angle information. Then, the communication rate is maximized while satisfying sensing requirements, which is proved to be a monotonic optimization problem on time allocation. Furthermore, we unveil the feasible condition of the problem and propose a polyblock-based optimal algorithm. Simulation results validate that the performance trade-off bound of S&C is significantly enlarged by the novel design exploiting mutual assistance in intelligent surface-aided vehicular networks.

cs.IT↗
arXiv2023

UAV-Enabled Integrated Sensing and Communication: Opportunities and Challenges

Unmanned aerial vehicle (UAV)-enabled integrated sensing and communication (ISAC) has attracted growing research interests in the context of sixth-generation (6G) wireless networks, in which UAVs will be exploited as aerial wireless platforms to provide better coverage and enhanced sensing and communication (S&C) services. However, due to the UAVs' size, weight, and power (SWAP) constraints, controllable mobility, and line-of-sight (LoS) air-ground channels, UAV-enabled ISAC introduces both new opportunities and challenges. This article provides an overview of UAV-enabled ISAC, and proposes various solutions for optimizing the S&C performance. In particular, we first introduce UAV-enabled joint S&C, and discuss UAV motion control, wireless resource allocation, and interference management for the cases of single and multiple UAVs. Then, we present two application scenarios for exploiting the synergy between S&C, namely sensing-assisted UAV communication and communication-assisted UAV sensing. Finally, we highlight several interesting research directions to guide and motivate future work.

cs.IT↗
arXiv2023

Transmissive Reconfigurable Intelligent Surface Transmitter Empowered Cognitive RSMA Networks

In this paper, we investigated the downlink transmission problem of a cognitive radio network (CRN) equipped with a novel transmissive reconfigurable intelligent surface (TRIS) transmitter. In order to achieve low power consumption and high-rate multi-streams communication, time-modulated arrays (TMA) is implemented and users access the network using rate splitting multiple access (RSMA). With such a network framework, a multi-objective optimization problem with joint design of the precoding matrix and the common stream rate is constructed to achieve higher energy efficiency (EE) and spectral efficiency (SE). Since the objective function is a non-convex fractional function, we proposed a joint optimization algorithm based on difference-of-convex (DC) programming and successive convex approximation (SCA). Numerical results show that under this framework the proposed algorithm can considerably improve and balance the EE and SE.

eess.SP↗
arXiv2023

Fundamental Limits of Intelligent Reflecting Surface Aided Multiuser Broadcast Channel

Intelligent reflecting surface (IRS) has recently received significant attention in wireless networks owing to its ability to smartly control the wireless propagation through passive reflection. Although prior works have employed the IRS to enhance the system performance under various setups, the fundamental capacity limits of an IRS aided multi-antenna multi-user system have not yet been characterized. Motivated by this, we investigate an IRS aided multiple-input single-output (MISO) broadcast channel by considering the capacity-achieving dirty paper coding (DPC) scheme and dynamic beamforming configurations. We first propose a bisection based framework to characterize its capacity region by optimally solving the sum-rate maximization problem under a set of rate constraints, which is also applicable to characterize the achievable rate region with the zero-forcing (ZF) scheme. Interestingly, it is rigorously proved that dynamic beamforming is able to enlarge the achievable rate region of ZF if the IRS phase-shifts cannot achieve fully orthogonal channels, whereas the attained gains become marginal due to the reduction of the channel correlations induced by smartly adjusting the IRS phase-shifts. The result implies that employing the IRS is able to reduce the demand for implementing dynamic beamforming. Finally, we analytically prove that the sum-rate achieved by the IRS aided ZF is capable of approaching that of the IRS aided DPC with a sufficiently large IRS in practice. Simulation results shed light on the impact of the IRS on transceiver designs and validate our theoretical findings, which provide useful guidelines to practical systems by indicating that replacing sophisticated schemes with easy-implementation schemes would only result in slight performance loss.

cs.IT↗
arXiv2023

Resource Allocation and Passive Beamforming for IRS-assisted URLLC Systems

In this correspondence, we investigate an intelligent reflective surface (IRS) assisted downlink ultra-reliable and low-latency communication (URLLC) system, where an access point (AP) sends short packets to multiple devices with the help of an IRS. Specifically, a performance comparison between the frequency division multiple access (FDMA) and time division multiple access (TDMA) is conducted for the considered system, from the perspective of average age of information (AoI). Aiming to minimize the maximum average AoI among all devices by jointly optimizing the resource allocation and passive beamforming. However, the formulated problem is difficult to solve due to the non-convex objective function and coupled variables. Thus, we propose an alternating optimization based algorithm by dividing the original problem into two sub-problems which can be efficiently solved. Simulation results show that TDMA can achieve lower AoI by exploiting the time-selective passive beamforming of IRS for maximizing the signal to noise ratio (SNR) of each device consecutively. Moreover, it also shows that as the length of information bits becomes sufficiently large as compared to the available bandwidth, the proposed FDMA transmission scheme becomes more favorable instead, due to the more effective utilization of bandwidth.

cs.IT↗
arXiv2023

How Practical Phase-shift Errors Affect Beamforming of Reconfigurable Intelligent Surface?

Reconfigurable intelligent surface (RIS) is a new technique that is able to manipulate the wireless environment smartly and has been exploited for assisting the wireless communications, especially at high frequency band. However, it suffers from hardware impairments (HWIs) in practical designs, which inevitably degrades its performance and thus limits its full potential. To address this practical issue, we first propose a new RIS reflection model involving phase-shift errors, which is then verified by the measurement results from field trials. With this beamforming model, various phase-shift errors caused by different HWIs can be analyzed. The phase-shift errors are classified into three categories: (1) globally independent and identically distributed errors, (2) grouped independent and identically distributed errors and (3) grouped fixed errors. The impact of typical HWIs, including frequency mismatch, PIN diode failures and panel deformation, on RIS beamforming ability are studied with the theoretical model and are compared with numerical results. The impact of frequency mismatch are discussed separately for narrow-band and wide-band beamforming. Finally, useful insights and guidelines on the RIS design and its deployment are highlighted for practical wireless systems.

cs.IT↗
arXiv2023

Design and Optimization for Transmissive RIS Transceiver Enabled Uplink Communication Systems

In this paper, a novel transmissive reconfigurable intelligent surface (RIS) enabled uplink communication system with orthogonal frequency division multiple access (OFDMA) is investigated. Specifically, a non-conventional receiver architecture equipped with a single receiving horn antenna and a transmissive RIS is first proposed, and a far-near field channel model based on planar waves and spherical waves is also given. Then, in order to maximize the system sum-rate of uplink communications, we formulate a joint optimization problem over subcarrier allocation, power allocation and RIS transmissive coefficient design while taking account of user quality-of-service (QoS) constraint. Due to the coupling of optimization variables, the optimization problem is non-convex, so it is challenging to solve it directly. In order to tackle this problem, the alternating optimization (AO) algorithm is utilized to decouple the optimization variables and divide the problem into two sub-problems to solve. First, the problem of joint subcarrier allocation and power allocation is solved via the Lagrangian dual decomposition method. Then, the RIS transmissive coefficient design scheme can be obtained by applying difference-of-convex (DC) programming, successive convex approximation (SCA) and penalty function methods. Finally, the two sub-problems are iterated alternately until convergence is achieved. Numerical results verify that the proposed algorithm has good convergence performance and can improve sum-rate of the proposed system compared with other benchmark algorithms.

cs.IT↗
arXiv2023

Quadrature Spatial Scattering Modulation for mmWave Transmission

In this letter, we investigate a novel quadrature spatial scattering modulation (QSSM) transmission technique based on millimeter wave (mmWave) systems, in which the transmitter generates two orthogonal beams targeting candidate scatterers in the channel to carry the real and imaginary parts of the conventional signal, respectively. Meanwhile, the maximum likelihood (ML) detector is adopted at the receiver to recover the received beams and signals. Based on the ML detector, we derive the closed-form average bit error probability (ABEP) expression of the QSSM scheme. Furthermore, we evaluate the asymptotic ABEP expression of the proposed scheme. Monte Carlo simulations verify the exactness and tightness of the derivation results. It is shown that the ABEP performance of QSSM is better than that of traditional spatial scattering modulation.

cs.IT↗
arXiv2023

RIS-Aided MIMO Systems with Hardware Impairments: Robust Beamforming Design and Analysis

Reconfigurable intelligent surface (RIS) has been anticipated to be a novel cost-effective technology to improve the performance of future wireless systems. In this paper, we investigate a practical RIS-aided multiple-input-multiple-output (MIMO) system in the presence of transceiver hardware impairments, RIS phase noise and imperfect channel state information (CSI). Joint design of the MIMO transceiver and RIS reflection matrix to minimize the total average mean-square-error (MSE) of all data streams is particularly considered. This joint design problem is non-convex and challenging to solve due to the newly considered practical imperfections. To tackle the issue, we first analyze the total average MSE by incorporating the impacts of the above system imperfections. Then, in order to handle the tightly coupled optimization variables and non-convex NP-hard constraints, an efficient iterative algorithm based on alternating optimization (AO) framework is proposed with guaranteed convergence, where each subproblem admits a closed-form optimal solution by leveraging the majorization-minimization (MM) technique. Moreover, via exploiting the special structure of the unit-modulus constraints, we propose a modified Riemannian gradient ascent (RGA) algorithm for the discrete RIS phase shift optimization. Furthermore, the optimality of the proposed algorithm is validated under line-of-sight (LoS) channel conditions, and the irreducible MSE floor effect induced by imperfections of both hardware and CSI is also revealed in the high signal-to-noise ratio (SNR) regime. Numerical results show the superior MSE performance of our proposed algorithm over the adopted benchmark schemes, and demonstrate that increasing the number of RIS elements is not always beneficial under the above system imperfections.

cs.IT↗
arXiv2022

Intelligent Surface Enabled Sensing-Assisted Communication

Vehicle-to-everything (V2X) communication is expected to support many promising applications in next-generation wireless networks. The recent development of integrated sensing and communications (ISAC) technology offers new opportunities to meet the stringent sensing and communication (S&C) requirements in V2X networks. However, considering the relatively small radar cross section (RCS) of the vehicles and the limited transmit power of the road site units (RSUs), the power of echoes may be too weak to achieve effective target detection and tracking. To handle this issue, we propose a novel sensing-assisted communication scheme by employing an intelligent Omni-surface (IOS) on the surface of the vehicle. First, a two-phase ISAC protocol, including the S&C phase and the communication-only phase, was presented to maximize the throughput by jointly optimizing the IOS phase shifts and the sensing duration. Then, we derive a closed-form expression of the achievable rate which achieves a good approximation. Furthermore, a sufficient and necessary condition for the existence of the S&C phase is derived to provide useful insights for practical system design. Simulation results demonstrate the effectiveness of the proposed sensing-assisted communication scheme in achieving high throughput with low transmit power requirements.

cs.IT↗
arXiv2022

Robust Sum-Rate Maximization in Transmissive RMS Transceiver-Enabled SWIPT Networks

In this paper, we propose a state-of-the-art downlink communication transceiver design for transmissive reconfigurable metasurface (RMS)-enabled simultaneous wireless information and power transfer (SWIPT) networks. Specifically, a feed antenna is deployed in the transmissive RMS-based transceiver, which can be used to implement beamforming. According to the relationship between wavelength and propagation distance, the spatial propagation models of plane and spherical waves are built. Then, in the case of imperfect channel state information (CSI), we formulate a robust system sum-rate maximization problem that jointly optimizes RMS transmissive coefficient, transmit power allocation, and power splitting ratio design while taking account of the non-linear energy harvesting model and outage probability criterion. Since the coupling of optimization variables, the whole optimization problem is non-convex and cannot be solved directly. Therefore, the alternating optimization (AO) framework is implemented to decompose the non-convex original problem. In detail, the whole problem is divided into three sub-problems to solve. For the non-convexity of the objective function, successive convex approximation (SCA) is used to transform it, and penalty function method and difference-of-convex (DC) programming are applied to deal with the non-convex constraints. Finally, we alternately solve the three sub-problems until the entire optimization problem converges. Numerical results show that our proposed algorithm has convergence and better performance than other benchmark algorithms.

eess.SP↗
arXiv2022

Multi-UAV Collaborative Sensing and Communication: Joint Task Allocation and Power Optimization

Compared to a single UAV with limited sensing coverage and communication capability, multi-UAV cooperation is able to provide more effective sensing and transmission (S&T) services. Nevertheless, most existing works on multi-UAV sensing mainly focus on mutually exclusive task allocation and independent data transmission, which did not fully exploit the benefit of multi-UAV sensing and communication. Motivated by this, we propose a novel multi-UAV cooperative S&T scheme with replicated sensing task allocation. Although replicated task allocation may sound counter-intuitive, it can actually foster cooperative transmission among multiple UAVs and thus reduce the overall sensing mission completion time. To obtain the optimal task allocation and transmit power of the proposed scheme, a mission completion time minimization problem is formulated. To solve this problem, a necessary condition for replicated sensing task allocation is derived. For the cases of replicated sensing, the considered problem is transformed into a monotonic optimization and is solved by the generic Polyblock algorithm. To efficiently evaluate the mission completion time in each iteration of the Polyblock algorithm, new auxiliary variables are introduced to decouple the otherwise sophisticated joint optimization of transmission time and power. While for the degenerated case of non-replicated sensing, the closed-form expression of the optimal transmission time is derived

cs.IT↗
arXiv2022

Rate-Splitting Multiple Access for Intelligent Reflecting Surface-Aided Secure Transmission

In this letter, we study a rate-splitting multiple access (RSMA)-based intelligent reflecting surface (IRS)-aided multi-user multiple-input single-output (MISO) secure communication system with a potential eavesdropper (Eve). Aiming to maximize the minimum secrecy rate (SR) among all the legitimate users (LUs), a design problem for jointly optimizing the transmit beamforming with artificial noise (AN), the IRS beamforming, and the secrecy common rate allocation is formulated. Since the design problem is highly non-convex with coupled optimization variables, we develop a computationally efficient algorithm based on the alternating optimization (AO) technique to solve it suboptimally. Numerical results demonstrate that the proposed design can significantly improve the max-min SR over the benchmark schemes without IRS or adopting other multiple access techniques. In particular, employing the RSMA strategy can substantially reduce the required numbers of IRS elements for achieving a target level of secrecy performance compared with the benchmark schemes.

cs.IT↗
arXiv2022

Codebook-Based Solutions for Reconfigurable Intelligent Surfaces and Their Open Challenges

Reconfigurable intelligent surfaces (RIS) is a revolutionary technology to cost-effectively improve the performance of wireless networks. We first review the existing framework of channel estimation and passive beamforming (CE & PBF) in RIS-assisted communication systems. To reduce the excessive pilot signaling overhead and implementation complexity of the CE & PBF framework, we conceive a codebook-based framework to strike flexible tradeoffs between communication performance and signaling overhead. Moreover, we provide useful insights into the codebook design and learning mechanisms of the RIS reflection pattern. Finally, we analyze the scalability of the proposed framework by flexibly adapting the training overhead to the specified quality-of-service requirements and then elaborate on its appealing advantages over the existing CE & PBF approaches. It is shown that our novel codebook-based framework can be beneficially applied to all RIS-assisted scenarios and avoids the curse of model dependency faced by its existing counterparts, thus constituting a competitive solution for practical RIS-assisted communication systems.

cs.IT↗