arXiv subjects

R. Gago

Publications and source records attributed to R. Gago.

4 recordsLinked to original sources

arXiv2024

Photoluminescence enhancement in quaternary III-nitrides alloys grown by molecular beam epitaxy with increasing Al content

Room temperature photoluminescence and optical absorption spectra have been measured in wurtzite In$_{x}$Al$_{y}$Ga$_{1-x-y}$N (x $\approx$ 0.06, 0.02 < y < 0.27) layers grown by molecular beam epitaxy. Photoluminescence spectra show both an enhancement of the integrated intensity and an increasing Stokes shift with the Al content. Both effects arise from an Al-enhanced exciton localization revealed by the S- and W-shaped temperature dependences of the photoluminescence emission energy and bandwidth respectively. Present results point to these materials as a promising choice for the active region in efficient light emitters. An In-related bowing parameter of 1.6 eV was derived from optical absorption data.

cond-mat.mtrl-sci↗

arXiv2024

Effect of the growth temperature and the AlN mole fraction on In incorporation and properties of quaternary III-nitride layers grown by molecular beam epitaxy

Indium incorporation into wurtzite (0001)-oriented In$_{x}$Al$_{y}$Ga$_{1-x-y}$N layers grown by plasma-assisted molecular beam epitaxy was studied as a function of the growth temperature (565-635 $^{\circ}$C) and the AlN mole fraction (0.01 < y < 0.27). The layer stoichiometry was determined by Rutherford backscattering spectrometry (RBS). RBS shows that Indium incorporation decreased continuously with increasing growth temperature due to thermally enhanced dissociation of In-N bonds and for increasing AlN mole fractions. High resolution x-ray diffraction and transmission electron microscopy (TEM) measurements did not show evidence of phase separation. The mosaicity of the quaternary layers was found to be mainly determined by the growth temperature and independent on alloy composition within the range studied. However, depending on the AlN mole fraction, nanometer-sized composition fluctuations were detected by TEM. Photoluminescence spectra showed a single broad emission at room temperature, with energy and bandwidth S- and W-shaped temperature dependences typical of exciton localization by alloy inhomogeneities. Cathodo-luminescence measurements demonstrated that the alloy inhomogeneities, responsible of exciton localization, occur on a lateral length scale below 150 nm, which is corroborated by TEM.

cond-mat.mtrl-sci↗

arXiv2012

Solid flow drives surface nanopatterning by ion-beam irradiation

Ion Beam Sputtering (IBS) is known to produce surface nanopatterns over macroscopic areas on a wide range of materials. However, in spite of the technological potential of this route to nanostructuring, the physical process by which these surfaces self-organize remains poorly under- stood. We have performed detailed experiments of IBS on Si substrates that validate dynamical and morphological predictions from a hydrodynamic description of the phenomenon. Our results elucidate flow of a nanoscopically thin and highly viscous surface layer, driven by the stress created by the ion-beam, as a description of the system. This type of slow relaxation is akin to flow of macroscopic solids like glaciers or lead pipes, that is driven by defect dynamics.

cond-mat.mtrl-sci↗

arXiv2007

Growth mechanisms and structure of fullerene-like carbon-based thin films: superelastic materials for tribological applications

In this chapter we review our findings on the bonding structure and growth mechanisms of carbon-based thin solid films with fullerene-like (FL) microstructure. The so-called FL arrangements arise from the curvature and cross-linking of basal planes in graphitic-like structures, partially resembling that of molecular fullerenes. This three-dimensional superstructure takes advantage of the strength of planar pi bonds in sp2 hybrids and confers the material interesting mechanical properties, such as high hardness, high elastic recovery, low-friction and wear-resistance. These properties can be tailored by controlling the curvature, size and connectivity of the FL arrangements, making these materials promising coatings for tribological applications. We have focused our interest mostly on carbon nitride (CNx) since nitrogen promotes the formation of FL arrangements at low substrate temperatures and they are emerging over pure carbon coatings in tribological applications such as protective overcoats in magnetic hard disks. We address structural issues such as origin of plane curvature, nature of the cross-linking sites and sp2 clustering, together with growth mechanisms based on the role of film-forming precursors, chemical re-sputtering or concurrent ion assistance during growth.

cond-mat.mtrl-sci↗