arXiv subjects

R. M. Jones

Publications and source records attributed to R. M. Jones.

At least 37 records · Page 2Linked to original sources

arXiv2010

First Beam Spectra of SC Third Harmonic Cavity at FLASH

Third harmonic superconducting cavities have been designed and fabricated by FNAL to minimise the energy spread along bunches in the FLASH facility at DESY. A module, consisting of four nine-cell 3.9 GHz cavities, has been installed in FLASH. The first measurement with beam excitation is presented, and the comparisons to transmission measurement without beam and simulations are made. Higher order modes (HOMs) are able to propagate to adjacent cavities through attached beam tubes. Modes from 1.3 GHz cavities in the module nearby also propagate into this module.

physics.acc-ph↗

arXiv2010

Higher Order Modes in Third Harmonic Cavities for XFEL/FLASH

We analyse higher order modes in the 3.9 GHz bunch shaping cavities recently installed in the FLASH facility at DESY. We report on recent experimental results on the frequency spectrum from probe based measurements made at CMTB at DESY. These are compared to those predicted by finite difference and finite element computer codes. This study is focused mainly on the dipole component of the multi-pole expansion of the wakefield.. The modes are readily identifiable as single-cavity modes provided the frequencies of these modes are below the cut-off of the inter-connecting beam pipes. The modes above cut-off are coupled to the 4 cavities and are distinct from single cavity modes

physics.acc-ph↗

arXiv2010

High Gradient Superconducting Cavity with Low Surface EM Fields and Well-Suppressed HOMS for the ILC

We present an optimized geometry for a 1.3 GHz superconducting cavity in which the surface electromagnetic fields have been minimized and the bandwidth of the fundamental mode has been maximized. We refer to this design as the New Low Surface Field (NLSF) cavity. Earlier work focused on properties of the fundamental mode. Here we additionally study higher order modes (HOMs), means of damping them, and short range wake fields. A two-band circuit model is employed in order to facilitate rapid characterization of cavity HOMs.

physics.acc-ph↗

arXiv2010

Recent Progress on a Manifold Damped and Detuned Structure for CLIC

A damped detuned structure for the main X-band linacs of CLIC is being investigated as an alternative design to the present baseline heavily damped structure. In our earlier designs we studied detuned structures, operating at 11.994 GHz, with a range of dipole bandwidths in order to ensure the structure satisfies beam dynamics and rf breakdown constraints. Here we report on the development of a damped and detuned structure which satisfies both constraints. Preparations for high power testing of the structure are also discussed

physics.acc-ph↗

arXiv2010

Status of COLDDIAG: A Cold Vacuum Chamber for Diagnostics

One of the still open issues for the development of superconducting insertion devices is the understanding of the beam heat load. With the aim of measuring the beam heat load to a cold bore and the hope to gain a deeper understanding in the beam heat load mechanisms, a cold vacuum chamber for diagnostics is under construction. The following diagnostics will be implemented: i) retarding field analyzers to measure the electron energy and flux, ii) temperature sensors to measure the total heat load, iii) pressure gauges, iv) and mass spectrometers to measure the gas content. The inner vacuum chamber will be removable in order to test different geometries and materials. This will allow the installation of the cryostat in different synchrotron light sources. COLDDIAG will be built to fit in a short straight section at ANKA. A first installation at the synchrotron light source Diamond is foreseen in June 2011. Here we describe the technical design report of this device and the planned measurements with beam.

physics.acc-ph↗

arXiv2010

Gallium Arsenide preparation and QE Lifetime Studies using the ALICE Photocathode Preparation Facility

In recent years, Gallium Arsenide (GaAs) type photocathodes have become widely used as electron sources in modern Energy Recovery Linac based light sources such as the Accelerators and Lasers in Combined Experiments (ALICE) at Daresbury Laboratory and as polarised electron source for the proposed International Linear Collider (ILC). Once activated to a Low Electron Affinity (LEA) state and illuminated by a laser, these materials can be used as a high-brightness source of both polarised and un-polarised electrons. This paper presents an effective multi-stage preparation procedure including heat cleaning, atomic hydrogen cleaning and the activation process for a GaAs photocathode. The stability of quantum efficiency (QE) and lifetime of activated to LEA state GaAs photocathode have been studied in the ALICE load-lock photocathode preparation facility which has a base pressure in the order of 10^-11 mbar. These studies are supported by further experimental evidence from surface science techniques such as X-ray Photoelectron Spectroscopy (XPS) to demonstrate the processes at the atomic level.

physics.acc-ph↗

arXiv2010

Beam Dynamics Investigation of the 101.28 MHz IH Structure as Injector for the HIE-ISOLDE SC Linac

The first phase of the HIE-ISOLDE project at CERN consists of a superconducting (SC) linac upgrade in order to increase the energy of post-accelerated radioactive ion beams from 2.8 MeV/u to over 10 MeV/u (for A/q = 4.5). In preparation for the upgrade, we present beam dynamics studies of the booster section of the normal conducting (NC) REX-ISOLDE linac, focused on the longitudinal development of the beam in the 101.28 MHz Interdigital H-mode Structure (IHS), employing a Combined Zero Degree Structure (KONUS), pulsing at a high gradient of over 3 MV/m. The evolution of the transverse emittance in the SC linac depends critically on the injected longitudinal phase space distribution of particles from the existing linac and, with a better understanding of the beam dynamics upstream, the performance of the upgrade can be optimised. Data taken during the commissioning phase of the REX-ISOLDE linac is analysed to understand the properties of the beam in the booster and combined with beam dynamics simulations which include the realistic fields of the IHS, determined from both simulation and perturbation measurement.

physics.acc-ph↗

arXiv2009

Third Harmonic Cavity Modal Analysis

Third harmonic cavities have been designed and fabricated by FNAL to be used at the FLASH/XFEL facility at DESY to minimise the energy spread along the bunches. Modes in these cavities are analysed and the sensitivity to frequency errors are assessed. A circuit model is employed to model the monopole bands. The monopole circuit model is enhanced to include successive cell coupling, in addition to the usual nearest neighbour coupling. A mode matching code is used to facilitate rapid simulations, incorporating fabrication errors. Curves surfaces are approximated by a series of abrupt transitions and the validity of this approach is examined

physics.acc-ph↗

arXiv2009

High-gradient SRF Cavity with Minimized Surface E.M. Fields and Superior Bandwidth for the ILC

Results are presented on an alternative cavity to the ILC baseline design of TESLA-style SRF main accelerating linacs. This re-optimised shape enhances the bandwidth of the accelerating mode and has reduced surface electric and magnetic fields, compared to the baseline design and some current high gradient designs. Detailed simulations on the e.m. fields for the New Low Surface Field (NLSF) cavity, including end-cell and coupler designs, are reported. The re-distributed dipole modes are also discussed.

physics.acc-ph↗

arXiv2009

Hie-Isolde High Beta Cavity Study and Measurements

The upgrade of the ISOLDE machine at CERN foresees a superconducting linac based on two gap independently phased Nb sputtered Quarter Wave Resonators (QWRs) working at 101.28MHz and producing an accelerating field of 6MV/m on axis. A careful study of the fields in the cavity has been carried out in order to pin down the crucial e-m parameters of the structure such as peak fields, quality factor and e-m power dissipated on the cavity wall. A tuning system with about 200kHz frequency range has been developed in order to cope with fabrication tolerances. In this paper we will report on the cavity simulations. The tuning plate design will be described. Finally the frequency measurements on a cavity prototype at room temperature will be presented.

physics.acc-ph↗

arXiv2009

Compensation of Transverse Field Asymmetry in the High-beta Quarter-wave Resonator of the HIE-ISOLDE Linac at CERN

The superconducting upgrade of the REX-ISOLDE radioactive ion beam (RIB) post-accelerator at CERN will utilise a compact lattice comprising quarter-wave resonators (QWRs) and solenoids, accelerating beams in the mass range 2.5 < A/q < 4.5 to over 10 MeV/u. The short and independently phased quarter-wave structures allow for the acceleration of RIBs over a variable velocity profile and provide an unrivalled longitudinal acceptance when coupled with solenoid focusing. The incorporation of the solenoids into the cryomodule shortens the linac, whilst maximising the acceptance, but the application of solenoid focusing in the presence of asymmetric QWR fields can have consequences for the beam quality. The rotation of an asymmetric beam produces an effective emittance growth in the laboratory reference system. We present modifications of the cavity geometry to optimise the symmetry of the transverse fields in the high-beta QWR. A racetrack shaped beam port is analysed and a modification made to the inner conductor with a geometry that will enable a niobium film to be effectively sputtered onto the cavity surface.

physics.acc-ph↗

arXiv2009

Beam Dynamics Studies for the HIE-ISOLDE Linac at CERN

The upgrade of the normal conducting (NC) Radioactive Ion Beam EXperiment (REX)-ISOLDE heavy ion accelerator at CERN, under the High Intensity and Energy (HIE)-ISOLDE framework, proposes the use of superconducting (SC) quarter-wave resonators (QWRs) to increase the energy capability of the facility from 3 MeV/u to beyond 10 MeV/u. A beam dynamics study of a lattice design comprising SC QWRs and SC solenoids has confirmed the design's ability to accelerate ions, with a mass-to-charge ratio in the range 2.5 < A/q < 4.5, to the target energy with a minimal emittance increase. We report on the development of this study to include the implementation of realistic fields within the QWRs and solenoids. A preliminary error study is presented in order to constrain tolerances on the manufacturing and alignment of the linac.

physics.acc-ph↗

arXiv2009

Investigation of an alternate means of wakefield suppression in the main linacs of CLIC

We report on suppression of long-range wakefields in CLIC accelerating structures. Strong detuning and moderate damping is employed. In these initial design studies we focus on the CLIC_G structure and enforce a moderate Q of 300 and 500. We maintain a dipole bandwidth of approximately 1 GHz as specified from breakdown constraints in a modified structure, CLIC_DDS. The circuit model, which facilitates a rapid design of manifolds slot-coupled to the main accelerating cells, is described.

physics.acc-ph↗

arXiv2009

SRF cavity geometry optimization for the ILC with minimized surface e.m. fields and superior bandwidth

The main linacs of the ILC consist of nine-cell cavities based on the TESLA design. In order to facilitate reaching higher gradients we have re-designed the cavity shape. This leads to a reduction, comparable to several current designs, in both the ratio of the surface electric field to the accelerating field (Es/Ea) and the magnetic field to the accelerating field (Bs/Ea). The bandwidth of the accelerating mode is also optimized. This new shape, which we refer to as the New Low Surface Field (NLSF) design, bears comparison with the Ichiro, Re-entrant and LSF designs.

physics.acc-ph↗

arXiv2009

Wakefield damping for the CLIC crab cavity

A crab cavity is required in the CLIC to allow effective head-on collision of bunches at the IP. A high operating frequency is preferred as the deflection voltage required for a given rotation angle and the RF phase tolerance for a crab cavity are inversely proportional to the operating frequency. The short bunch spacing of the CLIC scheme and the high sensitivity of the crab cavity to dipole kicks demand very high damping of the inter-bunch wakes, the major contributor to the luminosity loss of colliding bunches. This paper investigates the nature of the wakefields in the CLIC crab cavity and the possibility of using various damping schemes to suppress them effectively.

physics.acc-ph↗

arXiv2009

X-band crab cavities for the CLIC beam delivery system

The CLIC machine incorporates a 20 mrad crossing angle at the IP to aid the extraction of spent beams. In order to recover the luminosity lost through the crossing angle a crab cavity is proposed to rotate the bunches prior to collision. The crab cavity is chosen to have the same frequency as the main linac (11.9942 GHz) as a compromise between size, phase stability requirements and beam loading. It is proposed to use a HE11 mode travelling wave structure as the CLIC crab cavity in order to minimise beam loading and mode separation. The position of the crab cavity close to the final focus enhances the effect of transverse wake-fields so effective wake-field damping is required. A damped detuned structure is proposed to suppress and de-cohere the wake-field hence reducing their effect. Design considerations for the CLIC crab cavity will be discussed as well as the proposed high power testing of these structures at SLAC.

physics.acc-ph↗

arXiv2009

An alternate design for CLIC main linac wakefield suppression

The present design of the main accelerating structure for CLIC is based on heavy damping (WDS) with a Q of ~10. The wakefield suppression in this case entails locating the damping materials in relatively close proximity to the accelerating cells. Herein we present an alternate design for the main accelerating structures. We detune the lowest dipole band by prescribing a Gaussian distribution to the cell parameters and consider moderate damping Q~500 to prevent the recoherence of the modes; in this case the damping materials can be located at an extended distance from the accelerating structure. The procedure to achieve a well-damped wakefield is described. Results are presented elucidating the various designs including the current one which is being developed to incorporate r.f. breakdown, pulse surface heating and beam dynamics constraints.

physics.acc-ph↗

arXiv2009

Rapid cavity prototyping using mode matching and globalised scattering matrix

Cavity design using traditional mesh based numerical means (such as the finite element or finite difference methods) require large mesh calculations in order to obtain accurate values and cavity optimisation is often not achieved. Here we present a mode matching scheme which utilises a globalised scattering matrix approach that allows cavities with curved surfaces (i.e. cavities with elliptical irises and or equators) to be accurately simulated allowing rapid cavity prototyping and optimisation to be achieved. Results on structures in the CLIC main

physics.acc-ph↗