arXiv subjects

Rasmus Bjørk

Publications and source records attributed to Rasmus Bjørk.

15 recordsLinked to original sources

arXiv2026

Magnetic contacts on freestanding superconducting LaAlO$_3$/SrTiO$_3$ micromembranes

The superconducting two-dimensional electron gas (2DEG) at the LaAlO$_3$/SrTiO$_3$ (LAO-STO) interface is a promising platform for superconducting spintronics, however, integrating ferromagnetic contacts with the superconducting 2DEG remains challenging. Here, we realize superconducting LAO-STO micromembrane devices contacted by ferromagnetic nickel contacts through a side-contact geometry. Low-temperature transport measurements demonstrate that superconductivity is preserved in the presence of the ferromagnetic contacts. We show that the superconducting state is strongly influenced by the magnetic history of the nickel contacts, which generates a tunable effective magnetic field in the 2DEG. Through an effective field model, the magnetization of the contacts can be inferred from the maximum superconducting response. Our results establish ferromagnetically contacted LAO-STO as a platform for future investigations of spin injection into oxide superconductors and provide a route towards superconducting spintronic devices based on complex oxide interfaces.

cond-mat.supr-con↗

arXiv2026

Coils in thermomagnetic harvesters -- a comparative study

Thermomagnetic generators (TMGs) are devices that convert waste heat to electricity through a change in magnetization of a solid material. This causes a changing flux through a coil, which induces an electromotive force per Faraday's law. However, the influence of the coil on the performance of the TMG has not been investigated and existing TMG prototypes merely utilize some coil, not the optimal coil for a given device. In this work we present an analytical and numerical model of a TMG that calculates power by explicitly coupling the TMGs magnetic and electric circuits and use this to analyze the influence of the coil on the TMG performance. We show that analytically TMG power has a linear dependence on coil volume, independent of the specific combination of wire radius and coil turns. The model is validated with experimental data, and finally used to study prototype TMGs presented in literature, where we show that the power of these literature TMGs can be increased by a factor of 10-400 times, had larger coils been used in the prototypes.

physics.app-ph↗

arXiv2026

Exact demagnetisation field for periodic one-dimensional array of rectangular prisms

The magnetic field from a uniformly magnetised, rectangular prism is known exactly, which is the basis for a large number of micromagnetic simulations. Here we derive an analytical solution for the field from a periodically repeating infinite array of prisms aligned end-to-end, which becomes exact on the center axis in the limit of infinitesimally thin prisms. Using the same method we derive the on-axis field for a one-dimensional array of point dipoles. We validate the obtained results numerically and furthermore compare with the common macrogeometry approach and more recent uniform magnetisation method, demonstrating an excellent convergence rate for the novel method.

cond-mat.mtrl-sci↗

arXiv2026

Including sample shape in micromagnetics with 3D periodic boundary conditions

Periodic boundary conditions (PBCs) for computing magnetic fields in repeating magnetic structures, e.g. in micromagnetic simulations, are typically imposed using the quasi periodic macrogeometry approach, where many copies of the simulated domain are introduced. This can be computationally problematic, especially if the simulated domain is incommensurate with the desired sample shape. In this work, we present a formal proof that for sufficiently large magnetic samples, only the average magnetisation gives non-negligible shape effects. Using this insight, we develop a simple, computationally efficient modification of existing implementations which incorporates shape effects in PBC methods.

cond-mat.mtrl-sci↗

arXiv2026

Scalable physical source-to-field inference with hypernetworks

We present a generative model that amortises computation for the field and potential around e.g.~gravitational or electromagnetic sources. Exact numerical calculation has either computational complexity $\mathcal{O}(M\times{}N)$ in the number of sources $M$ and evaluation points $N$, or requires a fixed evaluation grid to exploit fast Fourier transforms. Using an architecture where a hypernetwork produces an implicit representation of the field or potential around a source collection, our model instead performs as $\mathcal{O}(M + N)$, achieves relative error of $\sim\!4\%-6\%$, and allows evaluation at arbitrary locations for arbitrary numbers of sources, greatly increasing the speed of e.g.~physics simulations. We compare with existing models and develop two-dimensional examples, including cases where sources overlap or have more complex geometries, to demonstrate its application.

cs.LG↗

arXiv2026

Instability-driven mechanically locked states in functional oxide membranes

Mechanical instabilities in thin solids offer a powerful route to engineer nonlinear responses, yet their controlled use in functional crystalline oxides has remained largely unexplored. Notably, by changing the aspect ratio of solids, the energy landscape around equilibrium can be modified to induce non-linearities under lateral stresses through non-lateral deformations. These nonlinear systems can develop multiple local energy minima where the system can settle and switch between states through the application of a driving force. Crucially, recent advances in oxide thin film growth have enabled the fabrication of freestanding oxide membranes, paving a viable path for their use in bistable architecture, particularly at the nanoscale. Here, we demonstrate that freestanding oxide membranes, such as SrTiO3 (STO) and BaTiO3 (BTO), relax into well-defined metastable buckling states when transferred onto lithographically defined cavities. The membrane deformation is determined by the interplay between built-in residual strain, bending stiffness, and cavity geometry, resulting in reproducible bistable states with distinct strain distributions. Using a combination of atomic force microscopy, in-contact Kelvin probe measurements, and finite-element modelling, we reveal that these mechanically locked states directly shape the electromechanical potential landscape of ferroelectric BaTiO3. We further demonstrate reversible snapthrough transitions between mechanically degenerate states, establishing complex oxides as deterministic, geometry-tunable building blocks for nonlinear nanoelectromechanical architectures. Our results illustrate a general strategy for exploiting mechanical instabilities to encode and manipulate functional responses in ultrathin crystalline membranes.

cond-mat.mtrl-sci↗

arXiv2026

The magnetic scalar potential for a rectangular prism

We analytically solve Poisson's equation for the magnetic scalar potential generated by a uniformly magnetized rectangular prism and determine a closed-form solution for the magnetic scalar potential given only in terms of arctan and natural logarithmic functions. We show that the magnetic scalar potential can be written as a demagnetization vector, containing all the geometric information, multiplied with the magnetization, analogous to demagnetization tensors. We validate the derived analytical expression for the magnetic scalar potential by comparing with a finite element simulation and show that these agree perfectly. We finally extend the concept of the demagnetization vector and tensor, which contains the geometric information for the source generating the potential, to gravitational objects.

physics.class-ph↗

arXiv2025

The magnetic scalar potential and demagnetization vector for a cylinder tile

A closed-form solution for the magnetic scalar potential generated by a uniformly magnetized cylindrical slice and a full cylinder is determined by solving Poisson's equation analytically. The solution is given in terms of elliptic integrals of the first, second and third kind. We show that the magnetic scalar potential can be written as the dot product of a demagnetization vector, containing all the geometric information of the generating cylinder, and the magnetization. We validate the derived analytical expressions for the magnetic scalar potential by comparing with a finite element simulation and show that these agree perfectly for both the cylindrical slice and the full cylinder.

physics.class-ph↗

arXiv2025

Magnetic levitation at low rotation frequencies using an on-axis magnetic field

The Ucar effect is a simple yet astonishing phenomenon where a permanent magnet can be levitated by placing it in the vicinity of another permanent magnet that rotates sufficiently fast. The few previous works on this type of magnetic levitation all required magnets rotating on the order of 200 Hz. Here we investigate the influence of applying a static magnetic field on the rotation axis and show that this can lower the needed rotation frequency to below 50 Hz. We explain this by a detailed analysis of the force producing levitation, which is a superposition of a repelling force caused by the off-axis (rotating) magnetic field and an attractive force due to the on-axis field. We study this force and resulting levitation experimentally, analytically and numerically for three different rotor magnet configurations, showing that trends in the levitation distance and frequency range can be accurately predicted from both the numerical and analytical models.

physics.class-ph↗

arXiv2024

Improving Electrical Contact Quality and Extraordinary Magnetoresistance in High Mobility III-V Semiconductors

Magnetometers based on the extraordinary magnetoresistance (EMR) effect are promising for applications which demand high sensitivity combined with room temperature operation but their application for magnetic field sensing requires further optimization. A key challenge is to obtain Ohmic metal/semiconductor contacts with low contact resistances in EMR devices comprising semiconductors with low carrier densities and high electron mobilities, yet, this topic remains scarcely investigated experimentally. By annealing high-mobility InSb in argon with systematically increasing temperatures, we experimentally demonstrate how the contact resistance to InSb films can be improved by two orders of magnitude by annealing to the micro-Ohm cm2 range without degrading the high mobility. We further show that lowering the contact resistance monotonously increases the room temperature magnetoresistance at 2 T from 700% to 65,000%. Lastly, we explore the origin of intrinsic magnetoresistance in high-mobility InSb thin films and suggest that it can best be explained by multiple band conduction.

physics.app-ph↗

arXiv2023

Magnetic levitation by rotation

A permanent magnet can be levitated simply by placing it in the vicinity of another permanent magnet that rotates in the order of 200 Hz. This surprising effect can be easily reproduced in the lab with off-the-shelf components. Here we investigate this novel type of magnetic levitation experimentally and clarify the underlying physics. Using a 19 mm diameter spherical NdFeB magnet as rotor magnet, we capture the detailed motion of levitating, spherical NdFeB magnets, denoted floater magnets. We find that as levitation occurs, the floater magnet frequency-locks with the rotor magnet, and, noticeably, that the magnetization of the floater is oriented close to the axis of rotation and towards the like pole of the rotor magnet. This is in contrast to what might be expected by the laws of magnetostatics as the floater is observed to align its magnetization essentially perpendicular to the magnetic field of the rotor. Moreover, we find that the size of the floater has a clear influence on the levitation: the smaller the floater, the higher the rotor speed necessary to achieve levitation, and the further away the levitation point shifts. We verify that magnetostatic interactions between the rotating magnets are responsible for creating the equilibrium position of the floater. Hence, this type of magnetic levitation does not rely on gravity as a balancing force to achieve an equilibrium position. Based on theoretical arguments and a numerical model, we show that a constant, vertical field and eddy-current enhanced damping is sufficient to produce levitation from rest. This enables a gyroscopically stabilised counter-intuitive steady-state moment orientation, and the resulting magnetostatically stable, mid-air equilibrium point. The numerical model display the same trends with respect to rotation speed and the floater magnet size as seen in the experiments.

physics.app-ph↗

arXiv2022

Extraordinary magnetometry -- a review on extraordinary magnetoresistance

Extraordinary magnetoresistance (EMR) is a geometric magnetoresistance effect occurring in hybrid devices consisting of a high-mobility material joined by a metal. The change in resistance can exceed 107% at room temperature when a magnetic field of 5 T is applied. Magnetic field sensors based on EMR hold the potential formeasuring weak magnetic fields with an unprecedented sensitivity, yet, to date this potential is largely unmet. In this work, we provide an extensive review of the current state-of-the-art in EMR sensors with a focus on the hybrid device geometries, the constituent material properties and applications of EMR. We present a direct comparison of the best devices in literature across magnetoresistance, sensitivity and noise equivalent field for different materials and geometric designs. The compilation of studies collected in this review illustrates the extremely rich possibilities for tuning the magnetoresistive behavior varying the device geometry and material properties. In addition, we aim to improve the understanding of the EMR effect and its interplay with geometry and material properties. Finally, we discuss recent trends in the field and future perspectives for EMR.

cond-mat.mtrl-sci↗

arXiv2022

Magnetic Field Prediction Using Generative Adversarial Networks

Plenty of scientific and real-world applications are built on magnetic fields and their characteristics. To retrieve the valuable magnetic field information in high resolution, extensive field measurements are required, which are either time-consuming to conduct or even not feasible due to physical constraints. To alleviate this problem, we predict magnetic field values at a random point in space from a few point measurements by using a generative adversarial network (GAN) structure. The deep learning (DL) architecture consists of two neural networks: a generator, which predicts missing field values of a given magnetic field, and a critic, which is trained to calculate the statistical distance between real and generated magnetic field distributions. By minimizing this statistical distance, a reconstruction loss as well as physical losses, our trained generator has learned to predict the missing field values with a median reconstruction test error of 5.14%, when a single coherent region of field points is missing, and 5.86%, when only a few point measurements in space are available and the field measurements around are predicted. We verify the results on an experimentally validated field.

cs.LG↗

arXiv2020

The stray- and demagnetizing field from a homogeneously magnetized tetrahedron

The stray- and demagnetization tensor field for a homogeneously magnetized tetrahedron is found analytically. The tetrahedron is a special case of four triangular faces with constant magnetization-charge surface density, for which we also determine the tensor field. The tensor field is implemented in the open source micromagnetic and magnetostatic simulation framework MagTense and compared with the obtained magnetic field from an FEM solution, showing excellent agreement. This result is important for modeling magnetostatics in general and for micromagnetism in particular as the demagnetizing field of an arbitrary body discretized using conventional meshing techniques is significantly simplified with this approach.

cs.CE↗

arXiv2017

The maximum theoretical performance of unconcentrated solar photovoltaic and thermoelectric generator systems

The maximum efficiency for photovoltaic (PV) and thermoelectric generator (TEG) systems without concentration is investigated. Both a combined system where the TEG is mounted directly on the back of the PV and a tandem system where the incoming sunlight is split, and the short wavelength radiation is sent to the PV and the long wavelength to the TEG, are considered. An analytical model based on the Shockley-Queisser efficiency limit for PVs and the TEG figure of merit parameter $zT$ is presented. It is shown that for non-concentrated sunlight, even if the TEG operates at the Carnot efficiency and the PV performance is assumed independent of temperature, the maximum increase in efficiency is 4.5 percentage points (pp.) for the combined case and 1.8 pp. for the tandem case compared to a stand alone PV. For a more realistic case with a temperature dependent PV and a realistic TEG, the gain in performance is much lower. For the combined PV and TEG system it is shown that a minimum $zT$ value is needed in order for the system to be more efficient than a stand alone PV system.

physics.app-ph↗