arXiv subjects

Riccardo DeSalvo

Publications and source records attributed to Riccardo DeSalvo.

16 recordsLinked to original sources

arXiv2026

A dual tunnel structure for the Einstein Telescope

We present a novel tunnel architecture for the Einstein Telescope that departs from the traditional large-cavern approach and reduces the excavated volume by an order of magnitude. In the proposed design, all seismic isolation systems are housed in raise-bore wells drilled upward from the main tunnel toward an upper service tunnel. The pre-isolators for the most sensitive optics are located in the service tunnel, seating directly on strong and compact rock, while the other filters are distributed along the wells within compact, side-access vacuum chambers. Shorter, separate wells accommodate the seismic isolation systems for less demanding optics. This configuration provides substantial advantages: easier lock acquisition and improved robustness of the interferometers, lower-frequency pendulum stages, reduced congestion around the test masses, simplified installation and maintenance, improved vacuum partitioning, strong physical decoupling between the high- and low-frequency interferometers, and enhanced compatibility with future advances of Newtonian-noise cancellation. A novel technique for real-time, precision monitoring of rock motion and tilt provides a new signal for Newtonian noise cancellation and enables correction of seismic disturbances even during earthquakes, offering unique geophysical measurement capabilities.

astro-ph.IM↗

arXiv2025

A cryogenic test-mass suspension with flexures operating in compression for third-generation gravitational-wave detectors

This paper presents an analysis of the conceptual design of a novel silicon suspension for the cryogenic test-mass mirrors of the low-frequency detector of the Einstein Telescope gravitational-wave observatory. In traditional suspensions, tensional stress is a severe limitation for achieving low thermal noise, safer mechanical margins and high thermal conductance simultaneously. In order to keep the tensional stress sufficiently low, we propose the use of rigid beams with large cross sections, combined with short flexures under compressional load. This configuration takes advantage of the many times higher strength of silicon in compression to respect to its strength in tension. The flexures are mechanically robust and at the same time soft in the working direction, thus producing low suspension thermal noise and, by being short, provide high thermal conductance for cryogenic cooling. The rigid beams, located between the test mass and an intermediate mass, allow the elimination of the recoil mass used conventionally for applying control forces for interferometer lock, and the use of optical anti-springs to reduce the pendulum resonant frequency to further improve the vibration isolation of the test mass. The configuration has the capability to reach a lower mirror operational temperature, which is expected to produce a substantial reduction of the thermal noise in the mirrors of the interferometer.

gr-qc↗

arXiv2022

Tunnel configurations and seismic isolation optimization in underground gravitational wave detectors

Gravitational wave detectors like the Einstein Telescope will be built a few hundred meters under Earth's surface to reduce both direct seismic and Newtonian noise. Underground facilities must be designed to take full advantage of the shielding properties of the rock mass to maximize the detector's performance. A major issue with the Einstein Telescope design are the corner points, where caverns need to be excavated in stable, low permeability rock to host the sensitive measurement infrastructure. This paper proposes a new topology that moves the top stages of the seismic attenuation chains and Michelson beam re-combination in separate excavations far from the beam-line and equipment induced noise while the test mass mirrors remain in the main tunnels. Distributing the seismic attenuation chain components over multiple tunnel levels allows the use of arbitrarily long seismic attenuation chains that relegate the seismic noise at frequencies completely outside the low-frequency noise budget, thus keeping the door open for future Newtonian noise suppression methods. Separating the input-output and recombination optics of different detectors into separate caverns drastically improves the observatory detection efficiency and allows staged commissioning. The proposed scheme eliminates structural and instrumentation crowding while the reduced sizes of excavations require fewer support measures.

astro-ph.IM↗

arXiv2020

Site-selection criteria for the Einstein Telescope

The Einstein Telescope (ET) is a proposed next-generation, underground gravitational-wave (GW) detector to be based in Europe. It will provide about an order of magnitude sensitivity increase with respect to currently operating detectors, and furthermore, extend the observation band towards lower frequencies, i.e., down to about 3Hz. One of the first decisions that needs to be made is about the future ET site following an in-depth site characterization. Site evaluation and selection is a complicated process, which takes into account science, financial, political, and socio-economic criteria. In this paper, we provide an overview of the site-selection criteria for ET, provide a formalism to evaluate the direct impact of environmental noise on ET sensitivity, and outline the necessary elements of a site-characterization campaign.

physics.ins-det↗

arXiv2015

Unaccounted source of systematic errors in measurements of the Newtonian gravitational constant G

Many precision measurements of G have produced a spread of results incompatible with measurement errors. Clearly an unknown source of systematic errors is at work. It is proposed here that most of the discrepancies derive from subtle deviations from Hooke's law, caused by avalanches of entangled dislocations. The idea is supported by deviations from linearity reported by experimenters measuring G, similar to what observed, on a larger scale, in low-frequency spring oscillators. Some mitigating experimental apparatus modifications are suggested.

cond-mat.mtrl-sci↗

arXiv2015

Material loss angles from direct measurements of broadband thermal noise

We estimate the loss angles of the materials currently used in the highly reflective test-mass coatings of interferometric detectors of gravitational waves, namely Silica, Tantala, and Ti-dop ed Tantala, from direct measurement of coating thermal noise in an optical interferometer testbench, the Caltech TNI. We also present a simple predictive theory for the material properties of amorphous glassy oxide mixtures, which gives results in good agreement with our measurements on Ti-doped Tantala. Alternative measure ment methods and results are reviewed, and some critical issues are discussed.

physics.optics↗

arXiv2014

Time dependences of atmospheric Carbon dioxide fluxes

Understanding the lifetime of CO2 in the atmosphere is critical for predictions regarding future climate changes. A simple mass conservation analysis presented here generates tight estimations for the atmosphere's retention time constant. The analysis uses a leaky integrator model that combines the observed deficit (only less than 40% of CO2 produced from combustion of fossil fuels is actually retained in the atmosphere, while more than 60% is continuously shed) with the exponential growth of fossil fuel burning. It reveals a maximum characteristic time of less than 23 year for the transfer of atmospheric CO2 to a segregation sink. This time constant is further constrained by the rapid disappearance of 14C after the ban of atmospheric atomic bomb tests, which provides a lower limit of 18 years for this transfer. The study also generates evaluations of other CO2 fluxes, exchange time constants and volumes exchanged. Analysis of large harmonic oscillations of atmospheric CO2 concentration, often neglected in the literature, indicate a strong. fast, time varying flux in and out of the atmosphere, with an exchange time constant of little more than one month. The correlation of oscillation amplitude with landmass distribution indicates that this oscillation may have a predominantly terrestrial origin. It is predicted that if the increase of anthropogenic CO2 production is halted, the CO2 concentration will stabilize within a quarter century.

physics.ao-ph↗

arXiv2014

Wiener filtering with a seismic underground array at the Sanford Underground Research Facility

A seismic array has been deployed at the Sanford Underground Research Facility in the former Homestake mine, South Dakota, to study the underground seismic environment. This includes exploring the advantages of constructing a third-generation gravitational-wave detector underground. A major noise source for these detectors would be Newtonian noise, which is induced by fluctuations in the local gravitational field. The hope is that a combination of a low-noise seismic environment and coherent noise subtraction using seismometers in the vicinity of the detector could suppress the Newtonian noise to below the projected noise floor for future gravitational-wave detectors. In this paper, we use Wiener filtering techniques to subtract coherent noise in a seismic array in the frequency band 0.05 -- 1\,Hz. This achieves more than an order of magnitude noise cancellation over a majority of this band. We show how this subtraction would benefit proposed future low-frequency gravitational wave detectors. The variation in the Wiener filter coefficients over the course of the day, including how local activities impact the filter, is analyzed. We also study the variation in coefficients over the course of a month, showing the stability of the filter with time. How varying the filter order affects the subtraction performance is also explored. It is shown that optimizing filter order can significantly improve subtraction of seismic noise, which gives hope for future gravitational-wave detectors to address Newtonian noise.

gr-qc↗

arXiv2010

Characterization of the seismic environment at the Sanford Underground Laboratory, South Dakota

An array of seismometers is being developed at the Sanford Underground Laboratory, the former Homestake mine, in South Dakota to study the properties of underground seismic fields and Newtonian noise, and to investigate the possible advantages of constructing a third-generation gravitational-wave detector underground. Seismic data were analyzed to characterize seismic noise and disturbances. External databases were used to identify sources of seismic waves: ocean-wave data to identify sources of oceanic microseisms, and surface wind-speed data to investigate correlations with seismic motion as a function of depth. In addition, sources of events contributing to the spectrum at higher frequencies are characterized by studying the variation of event rates over the course of a day. Long-term observations of spectral variations provide further insight into the nature of seismic sources. Seismic spectra at three different depths are compared, establishing the 4100-ft level as a world-class low seismic-noise environment.

gr-qc↗

arXiv2010

Measurement of Thermal Noise in Multilayer Coatings with Optimized Layer Thickness

A standard quarter-wavelength multilayer optical coating will produce the highest reflectivity for a given number of coating layers, but in general it will not yield the lowest thermal noise for a prescribed reflectivity. Coatings with the layer thicknesses optimized to minimize thermal noise could be useful in future generation interferometric gravitational wave detectors where coating thermal noise is expected to limit the sensitivity of the instrument. We present the results of direct measurements of the thermal noise of a standard quarter-wavelength coating and a low noise optimized coating. The measurements indicate a reduction in thermal noise in line with modeling predictions.

gr-qc↗

arXiv2009

Gravity-Gradient Subtraction in 3rd Generation Underground Gravitational-Wave Detectors in Homogeneous Media

In this paper, we develop a new approach to gravity-gradient noise subtraction for underground gravitational-wave detectors in homogeneous rock. The method is based on spatial harmonic expansions of seismic fields. It is shown that gravity-gradient noise produced by seismic fields from distant sources, stationary or non-stationary, can be calculated from seismic data measured locally at the test mass. Furthermore, the formula is applied to seismic fields from stationary local sources. It is found that gravity gradients from these fields can be subtracted using local seismic measurements. The results are confirmed numerically with a finite-element simulation. A new seismic-array design is proposed that provides the additional information about the seismic field required to ensure applicability of the approach to realistic scenarios even with inhomogeneous rock and non-stationary local sources.

gr-qc↗

arXiv2009

Simulation of underground gravity gradients from stochastic seismic fields

We present results obtained from a finite-element simulation of seismic displacement fields and of gravity gradients generated by those fields. The displacement field is constructed by a plane wave model with a 3D isotropic stochastic field and a 2D fundamental Rayleigh field. The plane wave model provides an accurate representation of stationary fields from distant sources. Underground gravity gradients are calculated as acceleration of a free test mass inside a cavity. The results are discussed in the context of gravity-gradient noise subtraction in third generation gravitational-wave detectors. Error analysis with respect to the density of the simulated grid leads to a derivation of an improved seismometer placement inside a 3D array which would be used in practice to monitor the seismic field.

gr-qc↗

arXiv2009

A Xylophone Configuration for a third Generation Gravitational Wave Detector

Achieving the demanding sensitivity and bandwidth, envisaged for third generation gravitational wave (GW) observatories, is extremely challenging with a single broadband interferometer. Very high optical powers (Megawatts) are required to reduce the quantum noise contribution at high frequencies, while the interferometer mirrors have to be cooled to cryogenic temperatures in order to reduce thermal noise sources at low frequencies. To resolve this potential conflict of cryogenic test masses with high thermal load, we present a conceptual design for a 2-band xylophone configuration for a third generation GW observatory, composed of a high-power, high-frequency interferometer and a cryogenic low-power, low-frequency instrument. Featuring inspiral ranges of 3200Mpc and 38000Mpc for binary neutron stars and binary black holes coalesences, respectively, we find that the potential sensitivity of xylophone configurations can be significantly wider and better than what is possible in a single broadband interferometer.

gr-qc↗

arXiv2007

Perspectives on Beam-Shaping Optimization for Thermal-Noise Reduction in Advanced Gravitational-Wave Interferometric Detectors: Bounds, Profiles, and Critical Parameters

Suitable shaping (in particular, flattening and broadening) of the laser beam has recently been proposed as an effective device to reduce internal (mirror) thermal noise in advanced gravitational wave interferometric detectors. Based on some recently published analytic approximations (valid in the infinite-test-mass limit) for the Brownian and thermoelastic mirror noises in the presence of arbitrary-shaped beams, this paper addresses certain preliminary issues related to the optimal beam-shaping problem. In particular, with specific reference to the Laser Interferometer Gravitational-wave Observatory (LIGO) experiment, absolute and realistic lower-bounds for the various thermal noise constituents are obtained and compared with the current status (Gaussian beams) and trends ("mesa" beams), indicating fairly ample margins for further reduction. In this framework, the effective dimension of the related optimization problem, and its relationship to the critical design parameters are identified, physical-feasibility and model-consistency issues are considered, and possible additional requirements and/or prior information exploitable to drive the subsequent optimization process are highlighted.

gr-qc↗

arXiv2007

Current status of Japanese detectors

Current status of TAMA and CLIO detectors in Japan is reported in this article. These two interferometric gravitational-wave detectors are being developed for the large cryogenic gravitational wave telescope (LCGT) which is a future plan for detecting gravitational wave signals at least once per year. TAMA300 is being upgraded to improve the sensitivity in low frequency region after the last observation experiment in 2004. To reduce the seismic noises, we are installing new seismic isolation system, which is called TAMA Seismic Attenuation System, for the four test masses. We confirmed stable mass locks of a cavity and improvements of length and angular fluctuations by using two SASs. We are currently optimizing the performance of the third and fourth SASs. We continue TAMA300 operation and R&D studies for LCGT. Next data taking in the summer of 2007 is planned. CLIO is a 100-m baseline length prototype detector for LCGT to investigate interferometer performance in cryogenic condition. The key features of CLIO are that it locates Kamioka underground site for low seismic noise level, and adopts cryogenic Sapphire mirrors for low thermal noise level. The first operation of the cryogenic interferometer was successfully demonstrated in February of 2006. Current sensitivity at room temperature is close to the target sensitivity within a factor of 4. Several observation experiments at room temperature have been done. Once the displacement noise reaches at thermal noise level of room temperature, its improvement by cooling test mass mirrors should be demonstrated.

gr-qc↗

arXiv2006

On the Analytic Structure of a Family of Hyperboloidal Beams of Potential Interest for Advanced LIGO

For the baseline design of the advanced Laser Interferometer Gravitational-wave Observatory (LIGO), use of optical cavities with non-spherical mirrors supporting flat-top ("mesa") beams, potentially capable of mitigating the thermal noise of the mirrors, has recently drawn a considerable attention. To reduce the severe tilt-instability problems affecting the originally conceived nearly-flat, "Mexican-hat-shaped" mirror configuration, K. S. Thorne proposed a nearly-concentric mirror configuration capable of producing the same mesa beam profile on the mirror surfaces. Subsequently, Bondarescu and Thorne introduced a generalized construction that leads to a one-parameter family of "hyperboloidal" beams which allows continuous spanning from the nearly-flat to the nearly-concentric mesa beam configurations. This paper is concerned with a study of the analytic structure of the above family of hyperboloidal beams. Capitalizing on certain results from the applied optics literature on flat-top beams, a physically-insightful and computationally-effective representation is derived in terms of rapidly-converging Gauss-Laguerre expansions. Moreover, the functional relation between two generic hyperboloidal beams is investigated. This leads to a generalization (involving fractional Fourier transform operators of complex order) of some recently discovered duality relations between the nearly-flat and nearly-concentric mesa configurations. Possible implications and perspectives for the advanced LIGO optical cavity design are discussed.

gr-qc↗